Question about 1984 Jeep CJ7

1 Answer

1984 CJ7 stuck in reverse. Staight 6, 5 speed and will not shift out of reverse.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

You have a bent shift fork or shaft, you will need to remove the dust boot pull the shift snap ring it the shifter is in the floor and pull the shifter stick off then remove the transmisson top cover and replace the reverse first shift fork, this is the most common cause, if it has a columm shifter then disconnet the shifter lever and try shifting if it shifts then you have bent linkage and will need to figure out where it is located.

Posted on Jul 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can i find free wire diagrams


free, for free google all day... join a real jeep forum and beg>?
sure
if time is more important.

alldata.com

log in and read.
or
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

Aug 08, 2014 | 1984 Jeep CJ7

1 Answer

Why the rear end tires on my 84 cj7 not spinning even when i put on reverse or first gear?


Is the rear driveshaft turning? If it is, likely you either have a broken axle or a blown gear set inside the differential. If it isn't, then there is a problem inside the transfer case.

Sep 17, 2010 | 1984 Jeep CJ7

1 Answer

I have an 84 cj 7 6 cyl 4 speed jeep...how do i bolt the transmission to the crossmember?


it is attached by the transmission mount,it cannot be bolted without the rubber mount

Nov 22, 2009 | 1984 Jeep CJ7

1 Answer

1984 Jeep CJ7 heater core leaking. '93 inline 6 motor. Wrangler dash. How to I remove the core?


  1. Disconnect battery ground cable and drain cooling system.
  2. Disconnect heater core hoses.
  3. Disconnect damper door control cables.
  4. Disconnect blower motor electrical connector.
  5. Disconnect water drain hose and defroster hose.
  6. Remove nuts retaining heater housing assembly to instrument panel. Remove heater housing assembly by tilting heater downward to disengage it from air inlet duct and pulling toward rear of vehicle.
  7. Remove heater core from heater housing.
  8. Reverse procedure to install.

Nov 17, 2009 | 1984 Jeep CJ7

1 Answer

Need to know how to replace a water pump on 81 cj7


This is for an 82 Inline 6 Aldata doesnt go back that far, if you need further info Hit Me Back

  1. Disconnect battery ground cable.
  2. Drain cooling system.
  3. Disconnect radiator and heater hoses from water pump, Fig. 21.
  4. Remove drive belts.
  5. Remove fan shroud and fan.
  6. Remove water pump attaching bolts, then the water pump and gasket.
  7. Reverse procedure to install.

May 31, 2009 | 1984 Jeep CJ7

1 Answer

I have with a 84 jeep cj7 with a straight 6. what is HP?


243cid = 4.0L. That's what you have under the hood.

May 11, 2009 | 1984 Jeep CJ7

1 Answer

What trannies came stock on 1984 CJ7 258 CID 5-speed


T-5: The T-5 is a light duty 5 speed transmission used in CJs from 1982 until 1986

Apr 21, 2009 | 1984 Jeep CJ7

1 Answer

1984 Jeep CJ7, Gear shifting / Linkage problem


likely the shift rails are worn inside the trans. In changing shift, you have removed the wear on the end of the stick, but not the corresponding wear where the stick fits into. It will need to be taken apart to repair this. (would not hurt to have synchros replaced at the same time.) OR, replace transmission if you have an inexpensive one available.

Mar 10, 2009 | 1984 Jeep CJ7

1 Answer

1984 pup transmision


the shifter forks inside the trany is hung up take back out or slide back be sure in neutral when u get it to shift then put back in

Feb 10, 2009 | 1984 Isuzu Pickup

Not finding what you are looking for?
1984 Jeep CJ7 Logo

Related Topics:

270 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...