Question about 1998 Saturn SL

1 Answer

How to replace valve cover gasket - 1998 Saturn SL

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 86 Answers

Refer to here
http://wiki.answers.com/Q/How_do_you_replace_the_head_gasket_located_on_a_1998_Saturn_Sl2_automatic

Posted on Jul 15, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

freetek
  • 5568 Answers

SOURCE: 1994 Toyota Corolla - Valve COver Gasket Replacement

You need an aftermarket serviice manual from Haynes or Chilton. They will have that kind of info.
I know of no car (I don't know them all) where that is needed and depending on the cover material (sheet steel or cast), could lead to warping and new leaks. I always use a thin film of silicone whether it is specified or not and there are torque specs for ALL valve covers I have ever seen.  

Posted on Sep 13, 2008

  • 109 Answers

SOURCE: replace valve cover gaskets on subaru svx

I don't have experience with this engine but guess you won't have to remove it for valve cover gasket work but perhaps can lift it a bit [not by hand!] after loosening engine mounts.

Posted on Nov 18, 2008

  • 2 Answers

SOURCE: valve cover gasket replace on a subaru svx

ALL DATA time to R&R valve cover gaskets both sides is 2.1 hours. you will need to remove brackets and connectors on either side, It will also help to take the upper plenium bolts out but not completly pull the plenium. If you don't have a lot of mechanical experiance and some basic tools. you may want to consider to have a local a shop to perform this service for you after you get a estimate. RON.

Posted on Jan 18, 2009

leetamara
  • 702 Answers

SOURCE: valve cover gasket leaking

When you buy the valve cover set, it will include the spark plug well "O" rings. Simply remove the valve cover and on the underside of the valve cover, you'll see the "O" rings that need replaced and you'll see exactly how the valve cover gasket itself fits.

Posted on Feb 12, 2009

  • 61 Answers

SOURCE: how to replace valve cover gasket 1998 chevy malibu

The first step is to remove all the parts that are in the way of you being able to remove the valve covers. (Ex.: air intake, loose wires etc.) Then you will need to remove your valve covers (using basic tools) and be very careful to not let anything get on your lifters, which your valve covers protect. Once you have the valve covers off compare the new gaskets to make sure they are the right size. Then remove the old gasket and replace with the new one using a high temp gasket sealant (available at any auto parts store) to attach the gasket to the valve covers. Then tighten down snug and check for leaks after replaced. 

Posted on May 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace valve cover gasket


Remove wiper arms/ Remove wiper assembly/ Alternator/ Power Block/Remove intake manifold/ get new gaskets for that/ valve covers are now easily accesible . Great time to change the spark plugs and wires now. PCV valve/ Air Filter/The gaskets for my 3.3 '99 caravan were the thick rubber, and cost $120, For Valve cover gaskets, Get "THE RIGHT STUFF" and you can make your own set, black silicon gasket maker. Reassemble

Oct 12, 2014 | 1999 Chrysler Town & Country

Tip

Simple steps to replace the Valve Cover Gaskets on a Jaguar XJ8?


Replace the valve cover gasket if the valve cover gaskets are leaking or if they're worn. The procedure is as follows:--
1)First carefully remove the nuts holding the valve cover to the engine head.2
2)Then pull the valve cover off from the engine head .
3)You can use flat-tip screwdriver to remove the valve cover.
4)It will be very dirty inside so you will have to clean the mating surfaces on both the engine head and the valve cover.
5)Take your time and clean it completely.

6)You can use a bead of RTV sealant on both mating surfaces.

7)Then carefully seat the gasket to top of the engine head.
8)The gasket can only be fitted in one way. So fit it properely.
9)Then tightly Press the valve cover to the gasket
10)And tighten the valve cover nuts secure.

This will help.Good Luck.

on Mar 10, 2010 | Jaguar XJ8 Cars & Trucks

1 Answer

Valve cover leaks


Try replacing the valve cover gasket. If the valve cover gasket still leaks oil after replacement try adding standard 1/4 lock washers to the top of the valve cover bolts. I have a 2005 Suzuki Reno and had to replace the valve cover gasket several times. Adding the washers tightened the seal of the gasket and prevented any leaking,

Jan 13, 2014 | 2006 BMW 750Li

1 Answer

Valve cover won't come off


Follow the detailed procedure mentioned in the link below to remove replace VALVE cover:----
Click the link below:---
VALVE COVER GASKET REMOVAL GUIDE http://technoanswers.blogspot.in/2012/06/valve-cover-gasket-removal-guide.html

-----------
For more help on these issues,check the link below:---
Car oil leaks from valve cover gasket? http://schematicsdiagram.blogspot.com/2011/12/car-oil-leaks-from-valve-cover-gasket.html

--------
Lexus RX: Tapping noise under Valve Cover At Low RPM? http://technoanswers.blogspot.in/2012/04/lexus-rx-tapping-noise-under-valve.html
---------- How to replace Timing Belt,Water pump And Valve Guides on Mitsubishi Montero http://repairhelpcenter.blogspot.com/2012/10/how-to-replace-timing-beltwater-pump.html

----------
2000 Toyota Solara: Valve Cover Gasket Replacing? http://technoanswers.blogspot.in/2012/04/2000-toyota-solara-valve-cover-gasket.html

----------
Valve Cover Keeps Cracking? http://schematicsdiagram.blogspot.in/2012/04/valve-cover-keeps-cracking.html

----------
These details will help.
Thanks.

Nov 23, 2012 | 2006 Subaru Forester

2 Answers

How to replace valve cover gasket


Remove the valve cover, which is a simple bolt on component. Remove the old gasket and install the new one.

May 13, 2011 | 2004 Suzuki Forenza

1 Answer

I have a 95 honda accord with the non vetec motor. I recently replaced the spark plugs and valve cover gasket. After driving a couple of days, i noticed oil coming out from the back of the valve cover...


the valve cover gasket may not be seated right if you remove the valve cover check the gasket 4 damage if so replace with new one and make sure if there is a grove for the gasket to sit in that it is in all the way round , applying a little gasket glue on the valve cover befor fitting the gasket can help to keep the gasket in place when you refit to the engine

Sep 05, 2009 | Honda Accord Cars & Trucks

1 Answer

Trying to replace the valve cover gasket on the passenger of my 1987 ford bronco and cannot seem to get to it?


remove the valve cover bolts. remove the valve cover. scrape off the old gasket material off the cover and the engine. put the new gasket in place and replace the bolts and tighten...dont over tighten.

May 23, 2009 | 1987 Ford Bronco

1 Answer

How to replace valve cover gasket 1998 chevy malibu


The first step is to remove all the parts that are in the way of you being able to remove the valve covers. (Ex.: air intake, loose wires etc.) Then you will need to remove your valve covers (using basic tools) and be very careful to not let anything get on your lifters, which your valve covers protect. Once you have the valve covers off compare the new gaskets to make sure they are the right size. Then remove the old gasket and replace with the new one using a high temp gasket sealant (available at any auto parts store) to attach the gasket to the valve covers. Then tighten down snug and check for leaks after replaced. 

May 05, 2009 | Chevrolet Malibu Cars & Trucks

1 Answer

Valve cover gasket leaking


When you buy the valve cover set, it will include the spark plug well "O" rings. Simply remove the valve cover and on the underside of the valve cover, you'll see the "O" rings that need replaced and you'll see exactly how the valve cover gasket itself fits.

Feb 12, 2009 | 2001 Nissan Altima

2 Answers

I need to replace the valve cover gasket on my voltswagon jetta


you probably mean the valve head gasket.

In this case this is serious work and you should contact a local VW dealership or mechanic and have them do this work for you to insure a job well done. If you simply mean your Valve cover, then this is no big deal and can be done by taking out the 4 screws found at the corners of the valve cover and then simply lifting the cover free and replacing it with a new one/tightening the screws back down.

hope this helps :)

May 17, 2008 | 1992 Volkswagen Jetta

Not finding what you are looking for?
1998 Saturn SL Logo

Related Topics:

513 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...