Question about Jeep Liberty

1 Answer

Have a 2005 Jeep Liberty. After starting from a

Have a 2005 Jeep Liberty. After starting from a dead stop at bottom of hill, check engine light started flashing and couldn't accelerate past 30 mph. RPM didn't get much over 2. After reaching 'flat land' was able to increase speed and engine light stopped flashing.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,615 Answers

The flashing light indicates you have a big misfire that could damage the catalytic converter.. Being you were going uphill (under high load) this would indicate an ignition issue. You may have a bad coil or wires or a bad spark plug. The reason you could only go 30mph was because the computer was put in limp mode. This is a stratagy to prevent excessive damage to components. , Get it checked out ASAP

Posted on Jul 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Luz marcada con el numero cinco?


2003 Jeep Liberty- Reading Engine / Diagnostic Codes ...

? 1:13
https://www.youtube.com/watch?v=pGrPBBzp7wE
Jan 6, 2013 - Uploaded by DeathScouter
2003 Jeep Liberty- Reading Engine / Diagnostic Codes ..... error code will flash 2 times, brief pause, flash 1 time, pause, flash 5times, pause, ...

2005 Jeep Liberty possible cause of P0442 error. - YouTube

? 5:26
https://www.youtube.com/watch?v=2ba-gH0gadg
Dec 21, 2014 - Uploaded by TheBGravit
While replacing a bad fuel pump I believe I found the cause of a P0442 Error code. I was able to repair the ...

Jeep Liberty Questions - Cylinder Misfire code - CarGurus

www.cargurus.com > Questions > Jeep > Liberty

CarGurusMay 27, 2009 - My jeep Liberty 2009 does the same the Dashboard showed a code of cylinder .... i have a jeep liberty 2006 with the # 5 cylinder misfire. i replaced the sparks... I have a 2005 Jeep Liberty 6 cylinder, engine light came on scaned the ... 2002 jeep liberty camshaft posistion sensor error code p0340 5 answers.

Check Engine Light/Misfire Due to Intake Valve Locks ...

repairpal.com > Problems > Jeep > Liberty
Recently got a second hand 2005 Jeep Liberty Sport. Everything worked fine ... #5intake valve seat dropped and held open the intake valve. 2008 Jeep Liberty.

OBD-II Trouble Code: P0305 Cylinder 5 Five Misfire Detected

www.obd-codes.com/p0305


Dec 08, 2015 | 2005 Jeep Liberty

1 Answer

03jeep lbertyrandom missfire cyl 2 4 6check engine light flashing


Check Engine Light/Misfire Due to Intake Valve Locks ...

repairpal.com > Problems > Jeep > Liberty
Jeep Liberty Check Engine Light/Misfire Due to Intake Valve Locks/Valves. ...Misfire cyc 4 and random cyc misfires, changed coil packs and plugs... sounds as if rod ... Light came on again (misfire on cylinder 4) - switched coil from 4 to 2. Light ...

Jeep Liberty Questions - Cylinder Misfire code - CarGurus

www.cargurus.com > Questions > Jeep > Liberty

CarGurusMay 27, 2009 - #4 misfire new plugs and coil pack on #4 light came back on after 300 miles if ... How come it stopped misfiring for 2-3 months, and now is back? ... I have a 2005 Jeep Liberty 6 cylinder, engine light came on scaned the codes ...

Liberty Cylinder Misfire / Computer issue? - JeepForum.com


Nov 28, 2015 | Cars & Trucks

2 Answers

I have a 2005 jeep liberty that's over heats any solutions?


full flush it yet. (AF change out is very limited)
rad tubes clogged, use pyro gun to find this easy.
bad pump. all AF goes acid if IGNORED.
fan belt slips.
Rad fans dead.
thermostat upside down
thermostat bleed hole not up hill , trapping air in block making gauge fail too.
is the block really full of AF or are you reading the liar tank, onside.
check rad levels in the RAD cap neck for full or not. dead cold.

is it is really overheating or only the fibbing gauge , tells you that,?
no steam?
no bursting of AF out side tank
no pinging,?
no loss of power.?
lots and lots of signs , not one stated.......do so please.
A/C trips off line? (it too has over heat detection)

Jul 02, 2014 | 2005 Jeep Liberty

1 Answer

Heat temp varies on 2002 Jeep Liberty


the heater fan is dead. blower.
check the heater fan fuse for BLOWN.

Feb 14, 2014 | Jeep Liberty Cars & Trucks

1 Answer

Jeep liberty 2005 crd start and engine goes off after four seconds


To start with, most models have a fuel pump relay that gives the pump voltage until the computer sees that the engine is running.
Sounds like the computer is not knowing the engine is running, so there is no power to the pump after it starts.
It could also be something with the anti-theft system.
Is the check engine light on ?

Jul 07, 2012 | 2005 Jeep Liberty

1 Answer

2005 jeep liberty has an engine light (yellow)staying on checked it out and checked fuel cap it is tight... now I have a knock or tick in the top of the engine... any help?


oil check oil. when light on dash comes on that means your jeep has a code for ya. take to auto zone and they will read the code for free with a code reader.

Feb 12, 2010 | 2005 Jeep Liberty

2 Answers

Driving up hill 2003 jeep liberty died.


Sounds like you may need a fuel/air mixture adjustment, this is quite common with higher altitudes than what your vehicle is normally running in...

Sep 16, 2009 | 2003 Jeep Liberty

1 Answer

2003 Jeep Liberty check engine and security Light


CK the mass air flow sensor. First sensor on duct coming out of air filter.

Jun 13, 2009 | 2005 Jeep Wrangler

1 Answer

Cuts off, but will restart, then cuts off again


Likely, you have a damaged engine bearing. When there is a problem there it will turn oil pressure light on because bearings keep the pressure inside the crankshaft...It may stop as the bearing overheats and binds, then loosens up a bit allowing a re-start when it gets cooler. Battery sounding dead is likely because the engine is locking up and too difficult for starter to turn.
At this point, it is not a do-it -yourself project ...either you need a lower end rebuild or engine replacement.

May 28, 2009 | 2004 Jeep Liberty

2 Answers

2003 3.7 Liberty check engine light for crank sensor


2003 3.7 Liberty check engine light for crank....what? sensor? You have scanned it?

Mar 06, 2009 | 2005 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

602 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...