Question about 1995 Nissan Pathfinder

1 Answer

93 Pathfinder: Where is cruise control module?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,784 Answers

To access the control module, remove the panel below the steering column. With the panel removed, the control module is visible to the right of the steering column, above the gas pedal.

Posted on Jul 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I troubleshoot the cruise control of a 2003 Alero?


It's probably a problem with cruise control module , located under the hood in engine compartment . Or a bad connection somewhere . Do you know how to do electrical testing ? Is the air bag light lit on the instrument cluster ?

Could have DTC'S - diagnostic trouble code's stored .
DTC P1554
The powertrain control module (PCM) inhibits cruise control operation when certain conditions are not appropriate for cruise control operation. The PCM removes the ground from the cruise control inhibit signal circuit in order to disengage cruise control operation.
DTC P1585
Output driver modules (ODMs) are used by the powertrain control module (PCM) in order to turn on many of the current driven devices that are needed to control various engine and transaxle functions. DTC P1558 set indicates that an improper voltage level has been detected on the signal circuit which controls the cruise control inhibit circuit.
Action Taken When the DTC Sets
• The PCM will not illuminate the malfunction indicator lamp (MIL).
• The PCM will store the conditions present when the DTC set as Failure Records data only.

Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions. However, steep grades may cause variations in the selected speeds. The electronic cruise control system has the capability to CRUISE, COAST, RESUME SPEED, ACCELERATE, and TAP-UP or TAP-DOWN.
The main parts of the cruise control system are:
• The cruise control module assembly
• The function control switches
• The cruise control release switch
• The clutch pedal position switch (CPP), if equipped
• The stop lamp switch assembly
• The vehicle speed sensor
The cruise control system uses the cruise control module assembly to maintain the desired vehicle cruise speed and operation. The cruise control module assembly has an electronic controller and an electric stepper motor to vary the throttle in each different cruise control mode. The electric controller monitors vehicle speed and operates the electric stepper motor. The stepper motor operates in response to the electronic controller, to maintain the desired cruise speed. The electric stepper motor moves a strap that is attached to the cruise control cable which moves the throttle linkage. The cruise control module assembly contains a low speed limit which will prevent system engagement below a minimum speed of 40 km/h (25 mph). The module assembly is not serviceable.

Dec 11, 2016 | 2003 Oldsmobile Alero

1 Answer

My cruise control won't work. How do I fix it in my 96 sunfire


Cruise Control Inoperative
Did you perform the Cruise Control System Check?
--
Go to Step 2
Go to Cruise Control System Check

2

  1. Disconnect the cruise control module connector.
  2. Turn the ignition switch to the RUN position.
  3. Measure the voltage between terminal F of the cruise control module harness connector and ground.
Does the voltage equal the specified value?
B+
Go to Step 3 yes
Go to Step 4 no

3

Measure the voltage between terminal E and terminal F of the cruise control module harness connector.
Does the voltage equal the specified value?
B+
Go to Step 5
Go to Step 6

4

Repair the open in CKT 339 between the fuse block and the cruise control module. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?
--
Go to Cruise Control System Check
--

5

  1. Turn the cruise switch to the ON position.
  2. Measure the voltage between terminal A of the cruise control module harness and ground.
Does the voltage equal the specified value?
B+
Go to Step 7 yes
Go to Step 8 no

Nov 21, 2015 | Cars & Trucks

1 Answer

Cruise control will not engage 2010 xf jaguar


Possible causes. The button, wiring from the button to the PCM, PCM, wiring from the PCM to the cruise control module, cruise control module. Which in your case , the cruise module is the throttle body module. Drive by wire. Have the codes read.

Oct 23, 2015 | 2010 Jaguar XF

1 Answer

I have a 93 Nissan pathfinder, the rear window defroster dosent work,how do i trouble shoot and repair it. also, i cant seem to get the cruse control to work, how do i trouble shoot and repair it. tha


The rear window defroster can be tested by checking for power out of the fuse box to the switch which operates a relay usually 4 pin 2 pins are the controlling side and the other 2 are battery power and the window element wire. Some switches have a led light in them that shows power is completed thru the switch . With a volt meter test wires at rear window some times if to many breaks in the grid stops the system from working. the cruise control has a servo with it's own throttle cable check for broken cable and check for engine vacuum to servo. then test switches on steering column with a ohm meter for proper continuity and test brake light switch.

Mar 23, 2014 | Cars & Trucks

1 Answer

2010 Nissan Pathfinder Cruise Control issues


First I'll assume you haven't read the owners Manuel, Cruise control is not perfect on any vehicle. if coming to a hill put foot on gas to help rpm, going down hill put foot on brake to keep same speed, cruise control operates off of engine vacuum. Speed sensors can be affected by putting on smaller or bigger tires than what is on drivers door.

May 24, 2017 | 2010 Nissan Pathfinder

1 Answer

93 toyota pickup 5 speed, speedometer and odometer work intermit


There is a plastic helical gear in the transmission, where the speedometer cable attaches. Start there. Usually 2-3 bolts that hold it in, when it comes out, some fluid will escape. Check that gear for wear, and broken splines. Then follow the cable up to the cruise control module. Some cars route the speedometer cable to the cruise control transducer, then to the firewall to the instrument cluster. That transducer goes bad. Thats what happened on my 81 olds. The speedometer would bounce around at speeds less than 15 mph. I replaced that transducer and it is steady now.

Nov 30, 2011 | Cars & Trucks

1 Answer

The cruise control light comes on but it does not engage. It's a 1995 pathfinder.


If your light comes on but the cruise control does not engage you may have a vacuum leak some where. When you set your cruise control your vehicle uses vacuum to maintain speed and if you have a vacuum leak this can not happen. Try checking all of your vacuum lines. I hope this helps.

Aug 26, 2011 | 1995 Nissan Pathfinder

1 Answer

Cruise control not working when it was it seammed to make the motor run very ruff when i disengaged it by using brake pedal


If the cruise control makes the engine seem to run very rough until disengaging it, there could be a problem with the engine itself. As, most cruise control systems just pull on the throttle cable to maintain speed on the highway based on setting the speed with the button.

So, I would look into the engine maybe having an issue with spark plugs, or wires, or another tuneup or mechanical issue.


Cruise Control Cable Removal & Installation To Remove:
chev_vent_cruise-cont-cabl-at-tb.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • The cable from the throttle lever and the accelerator control cable bracket gm_mv_ven_cruisecable.gif

    • The cable from the module by rotating the cable counter clockwise at the module
    • The cable from the module band
To Install:
NOTE: Ensure that the module strap is not twisted during cable installation
  1. Install or connect the following:
    • The cable to the module band
    • The cable to the module
    • The cable to the throttle lever and the accelerator control cable bracket
  2. Adjust the cruise control cable.
prev.gif next.gif Cruise Control Module Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following: gm_mv_ven_cruisecable.gif

    • The cruise control cable from the module gm_mv_ven_cruisecon.gif

    • The electrical connector gm_mv_ven_cruisebolt.gif

    • The mounting bracket bolt from the cruise control module
    • The cruise control module from the mounting bracket
To Install:
  1. Install or connect the following:
    • The cruise control module to the mounting bracket
    • The mounting bracket bolt to the cruise control module
      1. Torque to 53 inch lbs.(6 Nm)
    • The electrical connector to the module
    • The cruise control cable to the module

Oct 11, 2010 | 1999 Pontiac Montana

1 Answer

I have a problem with the "cruise control" from my Nissan


Hi, replace the resume/accel switch. I've seen alot of failures on this. If it still doesn't work, the cruise control module is the only thing that can possibly cause this problem. It's located in the left rear quarter panel behind the spare tire and plastic trim.

Mar 15, 2009 | 1992 Nissan Pathfinder

1 Answer

THE AUTOMATIC PILOT DOES NOT WORK


The cruise control is control on the 93-99 VW jettas and golfs by a computer module behind the headlight switch. Its common for these to fail. If you pull out your headlight switch you will see two square boxes, a black box, for the alarm, and a silver box for the cruise control replcae it by removing the cover under the steering wheel and unplugging the silver cruise control computer

Feb 25, 2009 | 1997 Volkswagen Jetta

Not finding what you are looking for?
1995 Nissan Pathfinder Logo

Related Topics:

331 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...