Question about 1991 Chevrolet K1500

1 Answer

Repair horn assy how do you remove the assy - 1991 Chevrolet K1500

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

Are you speaking of the horn? Or the horn relay? Or the horn button? Or the horn button split ring armature? To remove the horn assembly in the steering wheel you will need a steering wheel puller and a U shaped clamp that will screw down to the steering bolt you will need a 3/4 socket with a 3-inch extension and a ratchet. You will also need to picks to pull center snap ring off to get to the parts under the plate for the horn. To remove you will need to buy 2 security nuts tork wrenches #8 I believe, you will have to disconnect the battery before working on it as the bag could explode if you do not have the battery disconnected. After removing the positive side of battery cable wait 5 minutes before proceeding. Then remove the two bolts that hold the front horn assembly and air bag from the rear of the steering wheel next remove horn air bag assembly and disconnect the wire for the air bag. Place horn to the side then remove the 3/4 bolt out from the center, next install steering wheel puller on the steering wheel and put in three bolts and tighten them evenly so that the puller is on straight. Screw center bolt into the steering bolt until the wheel comes loose, remove steering wheel and place it at the side, next use the U shaped clamp to press the center plate down 1/4 inch to be able to clear the snap ring around the steering wheel. With one pick hold the ring in place with the other force it between the steering wheel bolt and work the ring up and out of the grove it sits in. Next work it all the way up till you have it in your hand, and do not lose. Now pull plastic plate off if you put the wheels straight then it will go on the same way you pulled it off because it's keyed mark it with a felt tip pen so you don’t have to hassle with keying it in again. Next remove the plate and there you will find the horn contacts and the round disk that the connectors push against, so if you need more info just ask on this post.

Posted on Jul 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 1994 chevy camaro,my steering column is bad.What range of years will fit?


If your talking about slack in the tilt part ,,, you can tightin it up,,, you will need a steering wheel puller and torx type sockets not sure the size ,,, once you get the steering wheel off ,horn assy out turn signal assy out,, the are 3 torx bolts that tightin it up ,,,remove bolts and use green lock tight on threads,,, reinstall and tightin ,, will never loosin agian if you use green lock tight

May 09, 2015 | 1994 Chevrolet Camaro

3 Answers

I have a 1998 chrysler concorde. The airbag light on the dash stays on and my horn doesnt work. How do i fix this without costing me tons of money?


Could be a wiring problem or the clockspring in the steering column.
You would need to pull the steering wheel and test the circuits.

Mar 26, 2015 | Chrysler Cars & Trucks

1 Answer

How do i remove the ignition switch on a 1987 chevrolet caprice to replace it lost keys?


(pain if you dont have the right tools)

also you are replacing the LOCK CYLINDER, the ignition switch is somewhere else

remove horn button

" steering wheel

" turn signal switch assy

" steering lock plate

" screw holding in lock cylinder

and it\'s not that easy

Oct 25, 2014 | Cars & Trucks

2 Answers

How to repair horn on 1998 honda civic lx


remove wire terminals and wire brush terminals

Oct 26, 2012 | 1998 Honda Civic

1 Answer

How to fix a 1995 eagle vision horn???


There is a horn relay also, but usually it's just a bad horn assy, unplug the horns and check for power to them with a test light while someone is pushing the horn pad!!

Jun 14, 2012 | 1995 Eagle Vision

3 Answers

Horn doesn't work airbag light on


sounds like the clock spring assy in the steering column is bad, Its a common problem for the caravan

Oct 25, 2010 | 2000 Dodge Caravan

2 Answers

Need to replace horn in 2000 F250


The horn is inside the right fender well, the inside fender well has to be removed for access but I believe the bolt for the horn assy. is under the battery tray and that may have to be removed also to gain access to the bolt.

Jul 20, 2010 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

Horn blows when turning steering wheel


You most likely have a broken wire under your steering wheel horn push housing and it's grounding itself during rotation of steering wheel , it may also be a spring broken on the horn push assy and the columb assy may be worth a peep . Good luck

Apr 05, 2010 | 1998 Ford Windstar

1 Answer

I have a 1999 Volkswagen jetta and i am trying to hook up an air horn to my alarm system and do not know the location of easy access wires to the horn of the alarm would you be able to help me find the...


The horn for the alarm is located beside the wiper motor assembly. You'll need to remove the wiper arm assy so you can remove the cowl panel and access the electric horn.

Nov 10, 2009 | 1999 Volkswagen Jetta

1 Answer

Broken horn


Most horns on GM cars are located low in front of one of the front wheels behind the fender. They are usually accessed by either removing the complete headlight assy or going from the bottom of the car and removing the plastin filler panel in front of the wheel.

Jun 21, 2009 | 1997 Chevrolet Cavalier

Not finding what you are looking for?
1991 Chevrolet K1500 Logo

352 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...