Question about 2000 Daewoo Nubira

1 Answer

Looking for diagram of head bolt torque and timing belt of a 2000 daewoo nubira 2.0

Posted by on

  • raul19 Jul 15, 2009

    MY BELT BROKE AND I GOT A REMAN HEAD...

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Daewoo Master
  • 450 Answers

Tighten the cylinder head bolts to 25 NSm (18 lb-ft) and turn the bolts another 3 turns of 90 degrees using the angular torque gauge.

looking for diagram of head bolt torque and timing - 7322e00.jpg

Posted on Jul 21, 2009

  • Steve Hurc
    Steve Hurc Jul 21, 2009


    Install the camshaft gears with the timing marks at

    the front.

    Insert the guide pin of the intake camshaft into the

    “IN” bore.

    Insert the guide pin of the exhaust camshaft into the

    “EX” bore.




×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need timeing belt diagram for 2000 dawoo nubria how to instill


CLICK HERE and HERE for timing belt information on the Nubria

blueextc3221_1.gif

Thanks for using FixYa

Aug 03, 2011 | 2000 Daewoo Nubira

1 Answer

Hi, need head torque settings for a 2000 daewoo nubira 1.6, thanks


In four stages, first with a calibrated torque wrench, then an angular torque gauge.

1st stage 25 nm (18 ft/lb) 2nd stage 60 deg
3rd stage 60 deg
4th stage 60 deg
5th stage 10 deg
order:
10. 6. 2. 3. 7. 9. 5 .1 .4 .8

New bolts ahould be used when head, and/or gasket is replaced.

Thank you for useing FixYa and i hope this answers your question.

Jun 28, 2011 | 2000 Daewoo Nubira

1 Answer

What are the torque specifications and tightening sequence for cam journal and cylinder head for 2001 daewoo nubira 2.0 :(


  1. The torque settings for the cylinder head bolts on a daewoo ...

    www.answers.com > ... > Categories > Cars & Vehicles > Asian Car i need how much pression (torque) for head daewoo nubira 2001 2.0 ... What is the cylinder head torque specs for a 2001 daewoo nubira 2.0 litre engine and ...

Apr 15, 2011 | 2001 Daewoo Nubira

1 Answer

What are the specs on head bolts


2001 Daewoo Nubira 2.0L MFI DOHC 4cyl

The Head Bolt Torque ...

Torque sequence ------------------------- Front | 10 6 2 3 7 | of | 9 5 1 4 8 | Engine --------------------------

Step 1 - Torque to 18 ft/lbs Steps 2 - Turn 90 degrees Steps 3 - turn 90 degrees Steps 4 - turn 90 degrees Recheck final torque in sequence


Hope helps (remember rated and comment this).

May 27, 2010 | 2001 Daewoo Nubira

2 Answers

2000 Daewoo Nubira camshaft position sensor


on the front under timing belt cover ,back cam ,if its not their then back of head about 3inches along from the gear wheel end

Sep 11, 2009 | 2002 Daewoo Nubira

1 Answer

Head bolts


You should really go get a manual for torquing head bolts. Not only to you have to torque them correctly, but there is a pattern as to which bolts you tighten so that you don't warp the head.

Jun 10, 2009 | 2000 Daewoo Nubira

2 Answers

Replacing timing belt on daewoo nubira 2000 model


Instructions Difficulty: Moderate Things You’ll Need:
  • Set of ¼-inch drive sockets ¼-inch drive ratchet Set of ½-inch drive sockets ½-inch drive ratchet Set of 3/8-inch drive sockets 3/8-inch drive ratchet Set of metric wrenches Floor jack Jack stands
Step1 Raise and support the vehicle on jack stands. Remove the intake air temperature wiring, the breather hose and intake air hose. Take off the air cleaner assembly. Step2 Remove the right wheel. Remove the accessory belts. Remove the crankshaft bolt and the crankshaft pulley. Remove the power steering bolts and the timing belt covers. Temporarily install the crankshaft bolt and turn the engine clockwise until the mark on the crankshaft pulley, which is a triangle stamped into the crank sprocket, is aligned with the corresponding triangular mark on the block. Step3 Make sure that the timing marks are aligned on the camshaft sprockets. These are a line on each sprocket that runs through a tooth on each sprocket. These lines should line up in the middle between each sprocket and point toward each other. If they do not line up, turn the crankshaft one more time and they will line up. It takes two turns of the crank to one complete revolution of the cam. Step4 Loosen the water pump bolts; using the 3/8-inch ratchet, turn the water pump clockwise away from the belt and loosely tighten the bolts to keep it there. Remove the timing beltmag-glass_10x10.gif. Make sure the timing marks are aligned and install the new belt starting on the right side from the crank sprocket and working counterclockwise. Keep all the belt tension on the right side away from the tensioner. Step5 Loosen the bolts in the water pump and rotate the water pump counterclockwise to apply tension to the belt. Watch the tensioner, which is above the water pump, and apply tension with the water pump until the pointer on the tensioner lines up with the notch above it. Lightly tighten the water-pump bolts. Step6 Turn the engine two more times and align the timing marks perfectly. Loosen the water-pump bolts and, using the ratchet, apply tension to the belt until the tensioner pointers are aligned. Tighten the water-pump bolts. Step7 Install the timing-belt covers and the bolts in the power-steering pump and tighten. Remove the crankshaft bolt and install the crank pulley and the bolt, then torque the crankshaft pulley bolt to 70 foot pounds of torque. Install all components in reverse order of removal.

Mar 02, 2009 | 2000 Daewoo Nubira

2 Answers

Change alternator on daewoo nubira


first you need to remove the belt . there are only several bolts to remove the alternator . there should be a diagram on the panel by the hood prop rod to show the belt route

Feb 18, 2009 | 2000 Daewoo Nubira

2 Answers

Need a picture diagram of 1999 daewoo Leganza timing belt setting or mars?


need a picture diagram for timing marks nubira 2001 2.0L

Jul 20, 2008 | 2002 Daewoo Nubira

Not finding what you are looking for?
2000 Daewoo Nubira Logo

1,464 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...