Question about 2001 Honda Accord

1 Answer

I have a 1997 accord and had to replace my alternator. The battery cables were removed and I expected to have to put in the security code, but nothing comes up on the radio. It is supposed to show the word code, but I get nothing. I checked the fuses and they are good - any ideas?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,129 Answers

Try installing a cd or pressing the on button several times

Posted on Jul 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1997 honda accord and my guages go dead all the lights on the car shut off when i start it then it only stays runing for a couple of sec then dies i tested my altornader and it failed


if alternator is bad you are not getting enough power for the lights etc, just battery power, and that is for starting vehicle if it has voltage. if alternator is good, it should put out at least 13.6-14.2 volts at battery with engine running.battery with car off, at posts should be 12.6 or better at battery. so if alternator is bad it needs replaced. needs proper voltage for pcm also. good-day !

Nov 12, 2011 | 1997 Honda Accord

2 Answers

I was having problems getting my 1997 jetta to start in the mornings, after getting it jumped, it would be okay. I replaced the battery and was having no problems. On Christmas Day, I didn't start it at...


CHECK ALTERNATOR OUT PUT SHOULD BE 13.5 VOLTS TO 14.5 VOLTS.IF NOT ALTERNATOR IS NOT CHARGING BATTERY.CHECK ALTERNATOR FUSE AND CHECK ALTERNATOR POSITIVE FEED WIRE AND VOLTAGE REGULATOR WIRES.IF ALL IS GOOD ALTERNATOR NEED TESTING AND REPLACED.IF ALTERNATOR GOOD BATTERY CABLES COULD BE OLD CAUSING POOR GROUND AND HIGH RESISTANCE IN POSITIVE CIRCUIT. STARTER SOLENOID FAULTY IF NOT BEEN REPLACED.

Dec 28, 2010 | 1997 Volkswagen Jetta

2 Answers

How do you replace a 1999 honda civic alternator?


8bcf5b0.jpg

Fig. Alternator wiring connector locations




6bd9106.jpg


Fig. Alternator bracket and bolt locations


  1. Note the radio security code and the radio presets.
  2. Disconnect the negative battery cable, then the positive.
  3. Remove the power steering pump.
  4. Detach the wiring from the alternator.
  5. Loosen the through bolt, then loosen the adjustment locknut. Then loosen the adjusting bolt.
  6. Remove the alternator belt.
  7. Remove all mounting and adjusting bolts and then remove the alternator unit.
To install:
  1. Installation is the reverse of removal.
  2. Adjust the alternator belt tension.
  3. Enter the anti-theft code for the radio.

Hope helps (remember rated this).

Aug 12, 2010 | 1999 Honda Civic

1 Answer

1997 honda accord se need to change vss,where


For 1997 Honda Accord 2.2L MFI 4cyl the Vehicle Speed Sensor - Location is located mounted on transmission.

OPERATION
The Vehicle Speed Sensor (VSS) is a magnetic pick-up sensor that sends a signal to the Powertrain Control Module (PCM) and the speedometer. The sensor measures the rotation of the output shaft on the transaxle and sends an AC voltage signal to the PCM that determines the corresponding vehicle speed.



TESTING
  1. Disconnect the negative battery cable.
  2. Disengage the wiring harness connector from the VSS.
  3. Using a Digital Volt-Ohmmeter (DVOM), measure the resistance (ohmmeter function) between the sensor terminals. If the resistance is 190-250 ohms, the sensor is okay.
REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Disconnect the three terminal connector from the vehicle speed sensor (VSS).
  3. Remove the fasteners that secure the VSS to the transaxle housing assembly.
  4. Remove the VSS.
To install:
  1. Install the VSS.
  2. Install the mounting bolts.
  3. Connect the three terminal connector to the sensor.
  4. Connect the negative battery cable.
Hope helps (remember rated this).

Jul 16, 2010 | 1997 Honda Accord

1 Answer

How do i replace an alt on an 97 Grand Voyager?


When you says ALT, I'm assuming that you are talking about ALTERNATOR...

REMOVAL & INSTALLATION
2.4L Engine
  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belt.
  3. Unplug the push-in field wire connector from behind the alternator.
  4. Remove the B+ nut and wire from behind the alternator.
  5. Remove the nut securing the top of the alternator to the adjuster bolt (a.k.a T-bolt).
  6. Remove the alternator pivot nut and bolt, located below the alternator.
  7. Remove the alternator from the vehicle.
To install:
  1. Install the alternator into position on the vehicle's engine.
  2. Install, but do not tighten, the alternator pivot nut and bolt.
  3. Install the nut securing the top of the alternator to the adjuster bolt.
  4. Connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  5. Plug in the push-in field wire connector onto the back of the alternator.
  6. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys, especially the alternator.
  7. Adjust the drive belt and tighten the adjuster/locking bolt to 40 ft. lbs. (54 Nm).
  8. Tighten the pivot bolt to 40 ft. lbs. (54 Nm).
  9. Reconnect the negative battery cable.
  10. Verify the charging rate of the alternator.

3.0L Engine
  1. Disconnect the negative battery cable.
  2. Remove the windshield wiper/motor module assembly.
  1. Remove the accessory drive belt from the alternator.
  2. Remove the bolt securing the top of the alternator to the mounting bracket.
  3. Remove the bolt securing the bottom of the alternator to the lower pivot bracket.
  1. While holding the alternator, unplug the push-in field wire connector from behind the alternator.
  2. While holding the alternator, remove the B+ nut and wire from behind the alternator.
  3. Remove the alternator from the vehicle.
To install:
  1. Hold the alternator in position near the mounting bracket, then connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  2. Plug in the push-in field wire connector onto the back of the alternator.
  3. Place the alternator into position on the mounting bracket, then install the bolt securing the bottom of the alternator to the lower pivot bracket.
  4. Install the bolt securing the top of the alternator to the mounting bracket. Tighten the upper and lower alternator bolts to 40 ft. lbs. (54 Nm).
  5. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys.
  6. Install the windshield wiper/motor module assembly.
  7. Reconnect the negative battery cable.
  8. Verify the charging rate of the alternator.

3.3L and 3.8L Engines
  1. Disconnect the negative battery cable.
  2. Remove the windshield wiper/motor module assembly.
  3. Remove the accessory drive belt.
  4. Remove the bolt securing the top of the alternator mounting bracket to the engine air intake plenum.
  1. Remove the bolts securing the outside of the alternator mounting bracket to the alternator mounting plate.
  2. Remove the bolt securing the top of the alternator to the mounting bracket.
  3. Remove the alternator mounting bracket from the vehicle.
  4. Rotate the alternator toward the dash panel.
  5. Unplug the push-in field wire connector from behind the alternator.
  6. Remove the B+ nut and wire from behind the alternator.
  1. Remove the bolt securing the bottom of the alternator to the lower pivot bracket.
  2. Remove the alternator from the vehicle.
To install:
  1. Install the alternator into position on the vehicle's engine.
  2. Install the bolt securing the bottom of the alternator to the lower pivot bracket.
  3. Connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  4. Plug in the push-in field wire connector onto the back of the alternator.
  5. Rotate the alternator forward away from the dash panel.
  6. Install the alternator mounting bracket in position on the vehicle.
  7. Install the bolt to secure the top of the alternator to the mounting bracket.
  8. Install the bolts to secure the outside of the alternator mounting bracket to the alternator mounting plate.
  9. Install the bolt to secure the top of the alternator mounting bracket to the engine air intake plenum.
  10. Tighten all of the alternator mounting bolts to 40 ft. lbs. (54 Nm).
  11. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys.
  12. Install the windshield wiper/motor module assembly.
  13. Reconnect the negative battery cable.
  14. Verify the charging rate of the alternator.

Hope helps woth this, remember rated this help. Good luck.

Jul 08, 2010 | 1997 Plymouth Grand Voyager

2 Answers

1997 Nisan Pick up alternator, is it difficult to replace


8 or 4 cylinder? 4 ain't that bad about half an hour or so. the 6 is about an hour or more depending on your skill and tools.

Dec 13, 2009 | 1997 Nissan King Cab

2 Answers

I need to replace my alternator


You need to first take off youre serptine belt. Inspect that and generally its a good idea to replace. Next there is a electrical connection on the alternator. DISCONNECT the battery FIRST!!!!!!!!!!!!!!!!!!!!!!!!! then disconnect the connection on the alternator, there are a couple of bolts that attach the alternator to the engine. and then simply bolt on the new one, re-attach the electrical connection and then re-install the (new) belt.

Aug 20, 2009 | 1992 Honda Accord

2 Answers

I have a 97 ford explorer all my lights in the interior came on my battery level went low and the car turned off as though i had no battery but i had just bought a new battery and recently changedle the...


12.6 is to low. It should be reading 13.8 to 14.5 when the alternator is functioning properly. Sounds to me like you got a bad connection or a bad alternator. hope this helps. good luck.

Aug 11, 2009 | 1997 Ford Explorer AWD

2 Answers

Ijust replaced the battery on my 1997 ford and battery is drainin


I've put in hundreds of alternators sometime a new one doesn't work properly you heed to check the voltage output of the vehicle running to see if it's charging or simple remove the negative battery cable while the vehicle is runnig, if it keeps running the alternator is working if it's dies it's not but you need to know the voltage output most vehicles it's 13.5 min.

Mar 23, 2009 | 1997 Ford Contour

1 Answer

How to change an alternator in 1983 honda accord


If your radio is coded, make sure you have the code and know how to re-enter the code in the radio.
  • Remove both battery cables and secure them away from the battery terminals.
  • Detach the E, F and N plug from the the alternator.
  • Slacken the alternator mounting bolts and move the alternator forward towards the engine.
  • Remove the drive belt.
  • Now undo all the mounting bolts and lift the alternator clear of the vehicle.
Re-fitting is just the reversal of the removal.

Nov 23, 2008 | 1983 Honda Accord

Not finding what you are looking for?
2001 Honda Accord Logo

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...