Question about Hyundai Tiburon

1 Answer

84 Eldo,windshield wiper fuse blows when washer used.switch rplcd

I have replaced the wiper switch. I have disconnected the washer motor, and it will still blow the 25 amp fuse. Does the washer motor circuit have to be in-line at all times or system treats it as a short? The other thing I noticed, was I took washer motor apart. It had a rusted out metal piece that appeared to go across both the wire contacts. This didn't make sense to me, because that seemed to be something that would cause a short. But on the other hand, I couldn't get an ohm reading without it making contact like that.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,129 Answers

The wiper motor is drawing to much amperage to do its job replace the wiper motor, but first disconnect the plug to inspect the connections if they are dirty clean the plug's conections with electrical contact cleaner and plug the plug in a few times to work out any corrosion if it is present on the connectors. sometimes sometimes the wiper arms can bind so after removing the wiper motor ensure that they are not binding by moving them by hand if they are offering a lot of resistance adress this issue first (lubricate or replace) to get to the clips on the wiper motor arm connections aquire a 45 degree long neck needle nose pliers the are a very handy tool to own.

Posted on Jul 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHERE IS THE WIPER/WASHER FUSE LOCATED ON 2007 PONTIAC TORRENT


In the under hood fuse box , should have diagram inside the lid . Front wiper's or rear ? Front fuse # 36 - 25 amp. Plus Two relay's PCB hi and Wiper PCB relay . Wouldn't think this being fuse problem . Wiper switch , motor etc... The wiper's are control by a computer . BCM - body control module .

The windshield wiper/washer system consists of front and rear wipers. The front and rear wipers are operative when the vehicle is in accessory or run. The front wipers have 4 different modes: Mist, Intermittent, Low, and High. When the front wipers are in the intermittent mode, there are 5 delay modes to chose from, commanded by the windshield wiper washer switch through the body control module (BCM). The rear wipers has an only one mode.

If the fuse is bad , could have a short to ground or wiper motor pulling to much current (amps) . Fuse's don't just blow for no reason ! Could also have DTC'S - diagnostic trouble codes stored in the BCM .
DTC B3715
DTC B3873
DTC B3875
DTC B3922

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
The BCM controls the windshield wiper motor through two output controls, controlling two different PCB relays which control the desired wiper speed, high or low.
DTC B3922 00: Front Wiper Function Select Circuit

The PCB relay's are non- servicable , replace fuse box . Soldered in Your best bet mit be to take it to a qualified repair shop .

Feb 20, 2017 | Pontiac Cars & Trucks

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

1 Answer

2003 Pontiac Montana wipers not working how to fix


First you need a wiring diagram, free at http://www.bbbind.com/free_tsb.html Then you need a DVOM - digital volt ohm meter to test the circuit . Then if your not familiar with automotive electrical systems testing ,go on youtube an check out Electric Testing Techniques You Need to Know Also having a factory diagnostic trouble shooting chart would also be usefull . You could just start replacing parts , you mite get lucky . The wiper motor is a high fail part , so is the switch ..You could find the fuse is blown ! But fuse's don't usually blow without a reason . Short to ground , low resistance . ( high current flow) Also knowing how they work and what all is involved in making them work.
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor module
• Windshield wiper motor
• Windshield washer pump motor
• FRT/WPR/WSHR 25A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all of the low speed modes. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits and the wiper motor high speed circuit.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.
Windshield wiper/washer system MIST operation is identical to LOW operation except that the MIST switch is a press and release type. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the windshield wiper motor will operate in the LOW mode until the switch is released.

Don't the wipers work in any mode ?
1
Did you review the Wiper/Washer System description and operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Wiper/Washer Systems
2
Turn ON the ignition , with the engine OFF.
Operate the windshield wiper/washer switch through all the switch positions.
Does the windshield wiper/washer system operate normally?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the harness connector of the windshield wiper motor.
Turn the ignition ON, with the engine OFF.
Connect a test lamp from the accessory voltage circuit of the windshield wiper motor to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 13
4
Connect a test lamp from the accessory voltage circuit to the ground circuit of the windshield wiper motor.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 14
5
Connect a test lamp from the signal 2 circuit of the windshield wiper switch to a good ground.
Press the windshield washer switch.
Does the test lamp illuminate?
YES - Go to Step 11
NO - Go to Step 6
Let me know if you make it this far and i will send rest of diagnostic's

Nov 25, 2016 | 2003 Pontiac Montana

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

2 Answers

I have a 2007 mustang an the wipers wont turn off I had 2 pull the fuse to turn them off can u help me


The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
Visual Inspection Chart Mechanical Electrical
  • Windshield washer pump hoses
  • Windshield wiper mounting arm and pivot shaft
  • Bussed electrical center (BEC) fuse 10 (30A)
  • Smart junction box (SJB) fuse 3 (10A)
  • Circuitry
  • Windshield wiper motor
  • Windshield washer pump
  • Windshield wiper/washer switch
  • The wipers stay on continuously
  • Circuitry
  • Windshield wiper motor
  • Windshield wiper/washer switch
  • Go To Pinpoint Test C .
PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY s6b~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH
  • Key in OFF position.
  • Disconnect: Windshield Wiper/Washer Switch C2137.
  • Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Does the windshield wiper/washer switch pass the component test?
Yes
GO to C2 .

No
INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND
  • Disconnect: Windshield Wiper Motor C125.
  • Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:

    Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)

    s6b~tr~en~file=n0011980.gif~gen~ref.gif
  • Are the resistances greater than 10,000 ohms?
Yes
GO to C3 .

No
REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
  • Disconnect all the windshield wiper motor connectors.
  • Check for:
    • corrosion.
    • pushed-out pins.
  • Connect all the windshield wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
You

Feb 20, 2015 | 2007 Ford Mustang Coupe

1 Answer

Windshield wiper fuse keeps blowing


Since you Disconnect the motor also renewed the switch and is still blowing the fuse ,it is obvious that you have either broken wire between the switch and the motor. Try to test the failure by means of a tester circuit. Good Luck.

Aug 21, 2012 | 2003 Mitsubishi Diamante

2 Answers

No windshield washer fluid pumping


1) Fluid resevoir is empty
2) Fluid is frozen
3) Washer fluid hose is disconnected, blocked or kinked
4) Washer switch is faulty
5) Washer pump motor is defective
6) Washer pump fuse is blown

Dec 24, 2010 | 2003 Oldsmobile Alero

2 Answers

Wiper stopped working...what is the problem


Wipers Not Working - Things to Check

To troubleshoot car windshield wiper problems, you need to thoroughly investigate problems with any of its operating parts. Here are some of the things that you need to check to determine why are your car windshield wipers not working.

Check Wiper Motor
The wiper motor is the driving force of the windshield wiper. Feel the motor and listen to a humming sound. If there is no humming, the motor is the problem. Check if the motor is working properly and see to it that its electrical connections are made properly. If you find that the motor is dead and beyond repair, get it replaced immediately.

Check For Break in Connecting Wires
The connecting wires of the motor sometimes go loose and that may cause the windshield wipers to stop working. Also check the battery plug connection which the motor has. Connecting the loose wires properly or fixing/replacing the plug might solve your problem.

Check Wiper Switch
Another wiper assembly part that can malfunction is the wiper switch itself. Check for switch malfunction and if you find that is indeed the problem, get it replaced from a mechanic.

Check for Bent Wiper Arms
Bent wiper arms can cause the operation of the wipers to be hampered. If the wiper arms are bent beyond repair, get them replaced immediately.

Check For Blown Out Car Fuse
A blown up car fuse could be the culprit that has stopped the windshield wipers from working. Check the fuse assembly under the dashboard of the car. Replacing a blown fuse might fix the problem of windshield wipers not working.

Windshield Wiper Sprayers Not Working - Things to Check

Sometimes the windshield wiper sprayer stops working which can be very annoying. The washer mechanism is a self cleaning mechanism for the windshield. Here are some of the things that you need to check in case it is not working.

Check Windshield Washer Motor
The windshield washer mechanism might have been impaired due to the malfunctioning of the wiper washer motor. Check if its working and get it replaced if it is beyond repair.

Check Windshield Washer Fluid Level
Sometimes the washer doesn't work because the washer fluid levels are not filled to requisite levels. Filling in fluid might restore normal functioning.

Check For Broken Washer Hose
The connecting washer hose that connects the reservoir to the nozzle, might be broken or worn out stalling the overall operation. Check the hose for leaks and get it replaced.

Check Washer Nozzle For Clogging
Last thing to check is the nozzle of the washer for clogging. An obstruction in the washer nozzle might be the reason for windshield wiper sprayers not working. Using a pin, clean the clogged nozzle. This might restore the sprayer to the normal working condition.

Jun 07, 2010 | 1998 Saturn SL

1 Answer

Windshield wiper fuse keeps blowing if I try to use the washer button.I replaced the switch. The washer motor at the bottle had a flat metal piece corroded in it. I disconnected the washer motor and it...


Pressing the screenwasher button usually energises a timer relay that provides four or five wiper sweeps so you will see the output wire from the switch does not go straight to the washer motor as in the really old days. The circuit is more complex...

If there is no obvious sign of a short circuit you really should be referring to a wiring diagram for further inspiration...

Aug 19, 2017 | 1984 Cadillac Eldorado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...