Question about 1991 Toyota Pickup

2 Answers

How to bleed clutch system in a toyota 4x4 pick-up 1989?

Posted by on

  • Anonymous Mar 27, 2014

    How do I bleed a clutch system on a toyota quantum

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 77 Answers

The clutch bleed is similar to brake bleeding. Find the bleeder valve for the clutch. It's usually located right by the Bell Housing of the transmission where the clutch fork is. Have extra fluid handy to refill the reservoir and check the fluid level after each bleed to make sure it doesn't get too low or you'll draw air back into the system. Make sure the fluid you use meets specs for your vehicle.
Have another person get in the vehicle and pump the clutch pedal several times and hold it to the floor. Open and close the bleeder valve very quickly. Do this procedure several times until you see a steady stream of fluid gushing from the valve. You should notice the clutch pedal getting firm.
Tighten valve securely, replace dust cover, and top off fluid.

*Note: You can use a can to catch the fluid that is released so you don't have fluid flying everywhere each time you open the valve. Another way to do this procedure is to hook a hose up to the bleeder valve and submerge the other end of the hose into a can of clean fluid to keep air from getting drawn back into the system.

Posted on Jul 15, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 148 Answers

First you need a buddy to help fisrt step is to check the fluid level in the clutch master cyliender located on the top left side of thr fire wall 2nd step locate the slave cyliender on the tranny nornally located on the right side just follow the steal line if its not make sure the bleeder screw will come loose then have you buddy push down on the pedal have them try not to go all the way down only 3/4 if possible then you close the bleeder screw have them release the pedal then you can reopen the screw and have them push the pedal agin

Posted on Jul 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, I have a toyota corolla 2e 1300 1989 model, I recently changed the gearbox and kits for the clutch master and slave Cylinders...... Now I have tried to bleed it to get clutch but it doesn't want to...


Did you bench bleed the MC before mounting it? If you have good pressure then it goes soft again then you still have air in the system or you have a leak that is sucking air into the system or your NEW MC is leaking internally.

Mar 14, 2015 | 1989 Toyota Corolla

1 Answer

How to bleed 89 ford ranger 4x4 clutch


there is a bleeder screw by the transmission slave cylinder that you bleed the air out.just pump the clutch pedal a few times hold the pedal to the floor and have someone crack open the bleeder screw to bleed the air out then close it and repeat.make sure the master cylinder for the clutch doesn`t go low.

Nov 02, 2011 | 1989 Ford Ranger

1 Answer

1986 22r 4x4 pick-up I need tips to replace clutch master cylinder and clutch release cylinder.


Start with the slave (release) cylinder. First take off the line and plug it with a golf tee or a short piece of hose with a bolt in the end. Remove the slave cylinder. Fill the new one with fluid and do the reverse. Then do the same thing with the master cylinder being careful not to lose any fluid. You may need to add fluid and bleed the system when finished.

Mar 18, 2011 | 1986 Toyota Pickup 4WD

1 Answer

I need help changing out the master cylinder in my '94 toyota 4x4 pickup truck. It is a 5speed, i have already changed out the slave cylinder and installed the master cylinder but i still can not get the...


did you bleed the system?? you must bleed the system from the clutch slave. if this has been done, I need more info!! How does the clutch pedal feel, is the clutch slave engaging at all??

Sep 27, 2010 | 1994 Toyota Pickup

1 Answer

Clutch problem


you still have air in the system very hard to bleed is the slave and master dry look under the dash at the master where it comes through the fire wall to see if it is wet some times you need to power bleed them

Feb 02, 2010 | 1991 Toyota Pickup

1 Answer

Need directions to bleed slave cylinder on '89 bronco 2 4x4


brakes or clutch??,if clutch get assistant to work pedal ,pump a few times then hold down ,you push the clutch arm in with a bar and open the bleed nipple at the same time then close the nipple and repeat ,after about 3/4 goes it should have pressure

Dec 22, 2009 | 1989 Ford Bronco II

1 Answer

My 4x4 toyota pick-up was stored for two years without running now my clutch stuck at the end i start my engine when it is engaged in first gear and it run ,i try to push on the clutch or change gear a...


Clutch system works exactly like hydraulic brake system. Check everything for leaks, make sure slave has not rusted and frozen in place and check that master cylinder is not bypassing internally. It's a good idea to bleed it out as well...fluid is hygroscopic and likely has drawn in water from the air over time (not good for system) That applies to brakes as well.

Jul 14, 2009 | 1991 Toyota Pickup

1 Answer

Can not find the clutch on the engine a toyota


the clutch is between the engine and gearbox .take off the gearbox and you will see it between the pressure plate and flywheel.

Jul 14, 2009 | 1991 Toyota Pickup

1 Answer

The clutch system won't work on my 1989 ford f150 4x4 5speed, have tried everything, all new parts, how do you bleed it?


if you have a hydrau7lic clutch you bleed it by having someone in the cab. have them push the clutch in and hold it. open the bleed screw til you have a steady stream with no air. reapeat the proccess . it's the same principle as bleeding brakes

Apr 26, 2009 | 1989 Ford F 150

Not finding what you are looking for?
1991 Toyota Pickup Logo

2,874 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8737 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...