Question about 1999 Ford Taurus

1 Answer

I have a 1999 ford taurus and has a code p0320 and keep cuting off

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 103 Answers

Here is what's more than likely the problem. the cam synchronizer and sensor is bad.it is located in back of intake manifold under injector /engine harness. sensor takes a 7/32 socket to get sensor off and a 10mm socket to pull out synchronizer. The assy is like a distributor and can not be put in in any way,you will need a alignment tool to make sure engine is at TDC and synchronizer is in synchronization with cam. this will cause check engine light and intermittently running bad if at all. they are not too expensive,probably under 200.00 for both pieces. have a ford technician install,they have the right tool from ford to make sure it's aligned properly. you should be out of there for under 400.00. you can request they don't charge you diag and take a gamble by having them install just that. I am only assuming it's a 3.0 ohv. I have done several of these for this concern and this code. good luck!

Posted on Jul 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 ford f150 has exhaust leak bought from dealer in may and code p0320 comes up and smells of burnt oil how dose this get fixed, is it expensive?


Here's the Ford discussion on it:
P0320 2000 Ford F150 Ignition Distributor Engine Speed Input Circuit...
It's not an exhaust issue. P0320 means that one of the ignition coils did not get an electrical pulse to make a spark plug spark.

On certain Ford models, one of the underhood wires rubs against an air conditioner tube and chafes through the insulation causing this fault. You can separate the wire and wrap it with electrical tape and use a cable tie to prevent rubbing. Here's a YouTube video which shows an easy way to fix it.

Oct 02, 2015 | Ford Cars & Trucks

1 Answer

2000 ford f150 Manuel trans. Code p0320 is it a expensive repair? Stutters while in gear 3/4 but doesn't stall. Just started a few days ago


P0320 means that an ignition pulse that's supposed to fire a spark plug was missed. It could be as simple as a chafed wire under the hood. Watch this video:


Ford has some information too:
P0320 2000 Ford F150 Ignition Distributor Engine Speed Input Circuit...

Oct 02, 2015 | Ford Cars & Trucks

2 Answers

1999 Ford Taurus abs system


You can look up any codes & go from there

If no codes-- check for corrosion on abs module harness
connector

Most likely you have a bad wheel speed sensor-- but need
the pcm to first run a check on abs at start up -then work
any codes.

Near impossible without factory manuals

I only have 2004 ford gas eng manuals --but if you have codes
I can work on something

Dec 01, 2012 | 1999 Ford Taurus

1 Answer

I need a diagram of how the plug wires are put on 1999 ford taurus station wagon


1999 Ford Taurus 3.0 liter V-6 VIN "2"

zjlimited_234.gif


1999 Ford Taurus 3.0 liter V-6 DOHC VIN "S"
and
1999 Ford Taurus 3.0 liter V-6 VIN "U"

zjlimited_235.gif


Hope helps (remember to rate and comment this answer).

Mar 07, 2011 | Ford Taurus Cars & Trucks

1 Answer

Need a diagram to replace a belt for a 3.0


1999 FORD TAURUS - V6 3.0L 182ci GAS FI N S - Belt Routing Diagram
1b3b0ad.jpg


1999 FORD TAURUS - V6 3.0L 182ci GAS FI N U and 1999 FORD TAURUS - V6 3.0L 182ci FLEX FI N 2 -
7257c46.jpg


From DAYCO Catalogue.

Hope helped.

Nov 04, 2009 | 1999 Ford Taurus

1 Answer

Egr code still present after changing solinoid and checking valve


Have you had the code reset using an OBD 1 scan tool? It must be reset as the code remains in the computer.

May 03, 2009 | 1999 Ford Taurus

1 Answer

Fault code


P0320 Ignition/Distributor engine speed input circuit
countrycurt0

Sep 05, 2008 | 2000 Ford Focus

Not finding what you are looking for?
1999 Ford Taurus Logo

1,237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...