Question about 2001 Dodge Durango

1 Answer

What are the inlet and outlet muffler measurements on a 4.7 L 2001 Dodge Durango? I have seen it listed as both 2.5 and 3 inches. Which is correct?

Posted by on

  • mmeisenhower Jul 17, 2009

    I crawled under there and measured and it is 2.5 for sure. Thanks for the help.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

2.5", 3" would be for performance exhaust.

Posted on Jul 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I measure the bolt pattern for a 2005 dodge ram 1500


To measure the bolt pattern of any Rim for any vehicle
You measure from the center of the Stud across diaganally
to another stud and if that measure ment is 5 1/2 inches or
4 1/2 inches whatever the tape measure says then your bolt
Pattern is the number of Studs by the measurement which means for example 5 X 5.5 that's your bolt patter and if they ask for
hub that's the round center hole of the rim You measure from inside across to inside edges so if it's 4 inches that's your hub. good luck.

Feb 26, 2015 | 2005 Dodge Ram 1500

1 Answer

Changed thermostsat enginne still running cold


WHEN ITS RUNNING FEEL THE INLET AND OUTLET OF THE HEATER CORE IF THEY ROUGLHY THE SAME TEMP BY FEEL YOU HAVE A BLEND DOOR ISSUE EITHER A ACTUATOR FAILURE OR A BROKEN BLEND DOOR. HAVE SEEN A LOT OF BOTH. IF THE COOLANT IS NOT GETTING WARM YOU MAY HAVE A FAN CLUTCH THAT IS NOT DISENGAGING CAUSING OVER COOLING OF THE COOLANT. HOPE THIS HELPS

Feb 22, 2013 | 1999 Dodge Durango

1 Answer

What fuse do I need to replace for my 99 Durango cigarette lighter/power outlet


it should be listed on the back of the cover for your fuse box, but if not, its a 15a fuse in slot 15. they are all numbered in the block

Aug 23, 2010 | 1999 Dodge Durango

1 Answer

What is a p0307 code on a dodge truck 1500 5.7 hemi 2004 the truck is missing on one cyl.


P0301-P0308....2T catalyst........2004-05 Ram...Cylinder 1-8 Misfire Detected Conditions: Any time engine is running and the adaptive numerator has been successfully updated. When more than 1.5% (300M, Magnum), 2% (Durango, Ram), 2.5% (Durango LEV, Ram LEV), misfire rate is measured during 2 trips, or with 10-30% misfire during 1 trip. 3 good trips required to turn off MIL. Possible Causes: ASD relay output 2 circuit fault Injector control 1 circuit fault Coil control 1 circuit fault Ignition wiring, spark plug, or ignition coil fault Fuel pump inlet strainer plugged Restricted fuel supply line Fuel pump module fault Fuel pressure leakdown fault Fuel injector is damaged or has failed Engine mechanical problems exist PCM has failed. Hope this helps you. Thank You for using fixya.If you like this solution please rate it....Thank You, iluv2fish....Ray

Jun 24, 2010 | 2004 Dodge Ram 1500

2 Answers

Location of oxygen sensor for 2000 dodge durango 4.0 4wd xlt?


There are 2. One is located above the catalytic converter most likely near the exhaust manifold where it attaches to the head. the second and most common one I have found to go bad is the down flow sensor located after the catalytic converter before the muffler on the underside.

Oct 19, 2009 | 2000 Dodge Durango

1 Answer

Where is the catalytic converter located on a 2000 Durango 4.7L


just follow your exhaust from your engine to your muffler. The catalytic converter is between the muffler and the engine. Looks like a miniature muffler.

Aug 15, 2009 | 2000 Dodge Durango

1 Answer

Need to the torque specs for a 1999 Dodge Durango


Head Torque sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs recheck final torque in sequence.

Torque intake manifold: Step 1: 12 inch/Lbs, (hand tight) Step 2: 72 inch/Lbs, (6) Ft/Lbs Step 3: 12 Ft/Lbs
torque intake plenum: Step 1: 24 inch/lb (hand tight) Step 2: 48 inch/lb (4) Ft/Lbs Step 3: 84 inch/lb (7) Ft/Lbs (To torque bolts, start in center using crisscross pattern)

Apr 07, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
2001 Dodge Durango Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...