Question about 1995 Jeep Wrangler

2 Answers

Over reving on start up

My freind replaced a bad water pump on his 1995 jeep wrangler. he replaced it but now when he starts the jeep it revs to about 4000 rpms or over any suggestions

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,615 Answers

Make sure all the connectors are on the throttle body and nothing is binding. Jeeps have a service bullitin about something like this. Try removing the IAC and clean the pintal area or replace the IAC. I have a 93 wrangler and I have had this happen to me. I cleaned it and it worked. Try disconnecting the battery for a few minutes then try it again. This will reset the IAC to MIN. If this allows it to start at a lower RPM then you Isolated the problem. Try tappping on the IAC also. It may be sticking. Either way if anything make a difference then you will prabable need An IAC.Make sure you have no vacuum leaks anywhere. A vacuum leak will hold the idle higher also and the computer will close the IAC as far as possible to compensate.

Heres why you have a high RPM
When you start the car if you have a stuck open IAC or vacuum hose leak the O2 sensor will see this extra air and add fuel to compensate to maintaim a 14.7 to 1 ratio but also the computer will see your foot is off the gas and the throttle position switch is closed. Under this condition the computer will want a precalibrated RPM which is between 660 to about 750 rpm +or- some. It will close the IAC till it reaches this level.

Posted on Jul 14, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 653 Answers

There is no direct connection between the water pump and the throttle. It sounds like in his struggles to replace the water pump, he may have disturbed or damaged the throttle linkage, the throttle body, or MAP sensor.

Posted on Jul 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1995 jeep wrangler. 4 cl.2.5. Anyway its leaking underneath looks like lower hose has a hole afriend thinks it's my water pump i just see water coming down looks like from the clamp


Your friend is probably correct. The pump has a "weep hole" that leaks when the seals have failed. If tightening the clamp does nothing, replace the pump.

May 21, 2010 | 1995 Jeep Wrangler

2 Answers

1995 Jeep Wrangler 2.5L Fuel Pump/Check engine light


Could be one of several items...I'd check the fuel pump relay, auto shutdown relay and the ignition switch itself. I'd bet on it being one of those relays but, we all have been fooled at least once!!! I'd also make sure that body and engine grounding is good and clean. Relays can't work properly without a good ground.

Nov 03, 2009 | 1995 Jeep Wrangler

2 Answers

94 jeep wrangler. Replaced fuel pump relay, fuel pump, cap, rotor


i was having the same problem with my 95 jeep rio grande. i replaced , rotor and cap, sparkplug wires, sparkplugs, pick up plate, ignition coil. come to find out my ecu/ecm was bad . i replaced it and i havent had a problem since.

Jun 05, 2009 | 1995 Jeep Wrangler

2 Answers

Jeep wrangler bucking


how long has this been happing..one tank of fuel or more, could have been bad gas, replace filter,, put gas dryier in fuel tank..if it continues could possibly be transmission related..the reving down doesn't sound like transmission though if tansmission was slipping it would rev up..good luck

Jun 02, 2009 | 1997 Jeep Wrangler

1 Answer

1995 Jeep YJ Wrangler


Check the coolant sensor, cam and crank sensor and make sure they are all plugged in.

Apr 10, 2009 | 1995 Jeep Wrangler

1 Answer

Grinding then starting


sounds like the flywheel may be cracked

Apr 08, 2009 | 1995 Jeep Wrangler

1 Answer

Engine noise


You guessed it, the shaft bearings are shot.

Jan 27, 2009 | 1995 Jeep Wrangler

1 Answer

1995 jeep wrangler


if no check engine light is on, check the egr valve, sounds to me that it is stuck open or the egr silinoid is bad

Jun 21, 2008 | 1995 Jeep Wrangler

Not finding what you are looking for?
1995 Jeep Wrangler Logo

319 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...