Question about 2000 Chevrolet Blazer

1 Answer

Where is the mas air flow sensor on a 2000 chevy blazer? Is it hard to replace? About what does the part cost?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 290 Answers

The MAF is in-line between the air filter and engine intake. They are easy to replace but you may need to buy a "security" bit to get some of the screws out. Auto Zone list a cheaper one for around $100. You can try cleaning the thin wire elements with MAF sensor cleaner.....attached is a picture of the MAFWhere is the mas air flow sensor on a 2000 chevy - 1c5370c.jpg

Posted on Jul 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why does my 2000 nissan maxima looses power while driving


Sounds like the maf sensor. Im assuming its throwing a check engine light? Get it read at AutoZone and look up the code. Go from tjefe

Jun 03, 2014 | 2000 Nissan Maxima

1 Answer

2000 chevy blazer


Have you checked the coolant sensor or replaced it, and also have you looked at the fuel spider, I hear they go bad and cause it too run ruff and rich.

Jun 27, 2012 | 2000 Chevrolet Blazer

1 Answer

My chevy blazer 2000 ha a p0101 code changed the mass air flow sensor still does not want to accelerate


Hi there:
This code is set when the MAF (Mass Air Flow) meter is not sending the PCM the correct information. This can be due to a bad conection of the rubber intake hose between the MAF and the Throttle plate opening, a dirty air filter, a dirty mass air flow or a bad mass air flow.



Most programmer have you tie into the iat sensor in the mass air flow. this can cause the the iat sensor oto short out.


Hope helps.

Jun 20, 2012 | 1998 Chevrolet S-10 Pickup

1 Answer

2000 Corolla hard to start and slow acceleration


most probably the mass air flow if you have not recently had a timing belt done. If you have recently had a belt done seems that the cam is a tooth off, if the belt was never done verify that the belt has not jumped a tooth.

Aug 13, 2009 | 2000 Toyota Corolla

1 Answer

Chevy blazer 97 replaced the fuel regulator and pump and still


mine was doing the same thing, the mass air flow sensor and throttle position sensor were dirty...i changed the tps myself but had the dealer do the mas.

Jun 19, 2009 | 1997 Chevrolet Blazer

2 Answers

Code reading


Hi. this code represents an issue within the mass air flow sensor. it is malfunctioning at this point. the mass air flow sensor Measures the volume and density of air entering the engine, so the electronic control module can determine how much fuel is needed to maintain the correct air to fuel mixture. There are two basic types: heated wire and heated film (grid); both work on the same principle.

A faulty MAF will cause driveability problems resulting from incorrect ignition timing and improper air/fuel ratios.

this device is located Under hood, center, upper engine area, mounted on rear of air intake duct


To replace a MAF sensor:
  • Locate the sensor.
  • Disconnect the negative battery cable.
  • Unplug the wiring harness and vacuum hose.
  • Unscrew the two screws holding the sensor in place.
  • Reverse the procedures to install a new sensor.
Please rate and god bless:)


Apr 28, 2009 | 1996 Chevrolet Impala SS

3 Answers

1999 Chevy Blazer no power while driving, then full power, why?


is it easy to fmove catal. conv. try if its clogged. cheap try dont cost a peny. becareful with gasket. good luk claymister

Apr 20, 2009 | 1999 Chevrolet Blazer

1 Answer

I have a 2000 Chevy Blazer I have replaced


maf sensor, tps sensor,or timing gear

Apr 16, 2009 | 2000 Chevrolet Blazer

Not finding what you are looking for?
2000 Chevrolet Blazer Logo

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...