Question about 2006 Suzuki Forenza

1 Answer

A square with a diagonal line appears instead of the shift (P R N D 3 2 1) please advise... thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 29 Answers

This means your transmission range selector sensor has gone bad. This is a very common problem with Suzuki's. You can buy the part at oemsuzukiparts.com for about $35.

Posted on Jan 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I shift gears on my 2006 Suzuki Forenza the car jerks forward as if I'm driving a stick shift car. A black square with a line diagonally across it flashes


have the trans fluid level checked , when was it last changed , have the OBD codes read as might be a sensor/switch at fault. I would do this very soon in case you do more damage

May 23, 2014 | Cars & Trucks

1 Answer

Transmission shifts sometimes


You ned to be absolutely sure that the transmission shop used the PROPER ATF fluid! since Chrysler needs Chrysler ATF+3 fluid to behave properly. ATF+4 is a newer fluid and can be used if ATF+3 isn't available. Plus, you need to be certain the shop really changed the whole contents of old fluid, since about 45% of it is inside the torque converter, requiring a complete FLUSHING, not only replacing the 5 quarts from the tranmission pan. That is about 9 quarts in all.

Sep 30, 2012 | 1993 Dodge Spirit

2 Answers

1973 chevy c10 pickup 350, truck is an automatic, starts up and goes into reverse and 1st fine but when i accelerate and the transmission shifts from 1st to 2nd the rpms keep increasing but the speed never...


Yeah Brother, those old square bodies are still neat. I have a '74 I put on a 4x4 chassis and 6.2 diesel w/overdrive automatic(700R4). Most likely you have a TH350 turbo trans and on the side front is a vacuum actuated can that operates the shift of the tranny. Any vacuum line connected to the carb or intake manifold will supply vacuum to it. It's originally a steel line with rubber connector tubes on the ends. Check the tranny fluid after warm up, in park, and be sure it has enough fluid in it. Luck Bro.

Jul 07, 2017 | Chevrolet Cars & Trucks

1 Answer

Hi, My Grand Marquis 1997 was diagonized and the code was po71. Could you please advise me on the possible problems and how it could be fixed. Thanks.


This is the ambient air temp sensor. it is located in the air induction system. Between the air filter and throttle. it is a small sensor with one plug. Easy to replace just pull it out. Cost is around $20.00

Jan 21, 2011 | Mercury Grand Marquis Cars & Trucks

1 Answer

I had the Transmission fluid changed 6,000 miles ago. On occasion it shifts / slips "hard" between gears. I'm now told to have the complete system flushed including a new filter. Please advise if...


Check the vacuum lines going from trans to the intake. Sometimes that will cause it to rev real hi and shift real hard. Even a small leak. They prob jast dropped the pan and changed filter b4. That leaves the oil in the lines there. you have to pump it all out to change it all. My trans in my lincoln just went out. So i would say it wouldnt hurt to change it. Put some lucus trans treatment in it to. Couldnt hurt.

Nov 21, 2010 | 1999 Lincoln Continental

1 Answer

Hi i have a 1996 probe trans went bad so i put a trans from a 1996 contour the bell houseing was different so i chained it i but it in and the trans wont shift right if i put it in dive it takes off in 3...


Your shifting module(netural park switch) on the trans has to line up with the mark or slot. Key on car off block wheels, put car in first and see where the module shifts and do the same for all the gears to see if they are lining up. All so check the shifting cable make sure its at the right length.

Feb 14, 2010 | 1996 Ford Probe

2 Answers

2000 S80 Tranny wont shift to overdrive, and after stopping at a stop sign it wont shift to first, stays in 2 or 3, Turn key off and start the car, tranny shifts starts out in first, still no overdrive....


Greetings Idpeters:
Please check your transmission fluid level. After the engine is warm pull the transmission stick and make sure the level is close to the full line and that the transmission fluid is red and not brown. You may have to change your transmission fluid and screen. If you plan to do it yourself I can advise you on how to change it step by step or you can take it to a transmission shop or dealership for a transmission tune-up. Good Luck

Oct 13, 2009 | 2000 Volvo S80

1 Answer

Hello. Could you please advise me what the camshaft torque tightening specs are for a 1993 SEAT IBIZA . Thank you


CAM SHAFT BEARING CAPS 15 FT LBS. DRIVE SPROCKET BOLT 58 FT LBS. CAMSHAFT END PLAY IS 0.006 in. WARNING THIS IS THE 2.8L ENGINE WHEN TORQUEING CAM SHAFT BEARING CAPS YOU HAVE TO TIGHTEN THE BOLTS 2 TURNS AT A TIME IN A DIAGONAL PATTERN TO DRAW THE CAMSHAFT DOWN AGAINST THE VALVE SPRING.

Sep 29, 2009 | 2002 Volkswagen Golf

1 Answer

Warning Light


Hi,

Any developments with your Explorer?

Jul 07, 2008 | 1997 Ford Explorer AWD

1 Answer

BMW 318TI COMPACT SPORT 3 DOOR HATCH


this is a pad wear indicator light this means that your break pads will need to be changed soon. :)

Jul 06, 2008 | 1999 BMW 318 ti

Not finding what you are looking for?
2006 Suzuki Forenza Logo

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...