Question about 1989 Oldsmobile Cutlass Ciera

2 Answers

I cannot find the water bypass part that is located from the radiator to the motor...what is the real name to that pipe

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 297 Answers

It's your heater core lines. the 2 lines that come out of the fire wall on the passenger side under the hood.

Posted on Jul 14, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,129 Answers

There are only three hoses going to the radiator the upper raidiator hose lower raidiator hose and small hose call the overflow reserve tank hose, find the over flow tank or the small plastic tank used to add coolant to then locate and follow it to the radiator.

Posted on Jul 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a hose leaking water it is located just below the connection of the lower radiator hose at the connections of the engine - i need to replace the hose and its in a very hard to reach spot - what is...


FWD car blues...... what engine option?
if you cant reach the clamps with simple accesory parts removal.
then its FWD blues. front wheel drive, ,
id say check the FSM. or alldata.com for how to do this.
there is no magic here, how to reach things, depends on persons size too. so.?????
did you look under the fender for access plates? behind tire>

the parts list on line at honda tell you the names
ever look there, water hose. bypass, heater, etc.>>>.

on some cars some hose are very hard to replace.
some even need the alternator pulled. or other parts .
for sure not the whole engine.

there are only 6 hose (water) small on the engine
3 bypass hose below the Throttle body. &1 at middle of long pipe.
long steel water manifold. pipe.
and 1 larger at from block to heater valve
and 2 larger going to , heater,

did you ever click , the water hose name here?
http://www.realhondaparts.com/rwhonda/jsp/prddisplay.jsp?inputstate=5&catcgry1=ACCORD&catcgry2=1995&catcgry3=2DR+EX&catcgry4=KA4AT&catcgry5=WATER+HOSE+%28+95-97%29&ListAll=All&vinsrch=no&systemcomp=Engine&vinnoT=&trim=&trans=&view=normal

Sep 24, 2013 | 1995 Honda Accord

1 Answer

Starter relay location for 1999her Lexus ES300


Before servicing the vehicle, refer to the Precautions section. Remove or disconnect the following:
Drain engine coolant
V-bank cover
Accelerator cable
Intake air connector
Throttle Body
Upper and lower intake manifold assembly
Rear water bypass joint
Water bypass pipe
Water bypass pipe from the water pump
Wire clamp from the bracket on the water bypass pipe
O-ring from the water bypass pipe
Water bypass pipe bracket from the water bypass pipe
2 bolts holding the starter to the cylinder block
Starter connector
Starter from the cylinder block
Nut, and disconnect the starter wire
Starter

Replacing a starter on 1999 Lexus ES300 was not all that hard. You had metric socket and combination wrenches and a phillip's screw driver. In this video show you how uninstalled the starter and then replaced it in pretty good detail. This starter is used in 1998 to 2001, and so basically you could use the same procedure that is shown there.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 10, 2011 | 1999 Lexus ES 300

1 Answer

2001 oldsmobile Silhouette what is the metal hose that goes around the front of the engine that the coolant goes through called?


water pump bypass pipe or "PIPE THERM BYPASS,(W/O OIL COOLER)" part #507950

http://www.gmpartseast.com/diagrams/large/35U/hoses-pipes-radiator-mu0103902.png

Oct 17, 2011 | 2000 Oldsmobile Silhouette

2 Answers

I need to know the name of the pipe conected to the bottom of the radiator into the motor?


this is called the coolant delivery line/hose. ( or coolant line/hose from the radiator to the water pump ).

c...

Feb 02, 2011 | 1995 Cadillac DeVille

1 Answer

Heating has stoped working and there is a little water in the oil, think radiator may be leaking, does my car just need a new rad


water in the oil will turn the oil brown like mud,is that what you see? if so,then you have a blown head gasket,do not run motor if this is the case as the motor wiil spin a crank bearing or lock up.are you sure about the water in the oil? look for real brown oil just like mud with bubbles on the oil dipstick. if the heats stopped working it may be because the radiator's low on fluid. look in the radiator for low coolant,if you can't see the coolant when you remove the radiator cap,it's low. with engine cool,remove the radiator cap 1st then start the engine. do you see steam and fluid blowing up frome the radiator? if so,you have a blown head gasket in the motor. head gaskets can blow and leak water into the oil or oil into the radiator. or blow and leak into the exhaust sysytem and blow coolant out of the tail pipe. three different ways for a head gasket to blow. usually the head gasket only blows when the engine has been run really hot!!! hope this helps.thank you for choosing fixya .com

Jan 06, 2011 | 1997 Hyundai Accent

1 Answer

The heater is blowing cold air


heater control valve not allowing radiator water to flow through the heater core where the heater blower motor blows the heat that radiates off the heater core into the vehicle cheap fix or you can bypass yourself by replacing valve with piece of 3/4 copper pipe and 2 hose clamps

Jan 03, 2011 | 1998 Dodge Caravan

1 Answer

Need to replace water pump on a 2000 Dodge Durango. Would like any details on how to to it.


3.9L, 4.7L, 5.2L, 5.9L, 8.0L Gasoline Engines
  1. Carry out the "Common Steps" above.
  2. Remove the upper radiator hose.
  3. Remove the fan and shroud assembly.
  4. On engines except 4.7L, remove the four water pump pulley bolts and remove the pulley.
  5. Remove the heater hose pipe mounting bolt, if fitted.
  6. On engines except 4.7L, loosen the bypass hose clamp at the water pump.
  7. Remove the seven water pump mounting bolts and, on the 4.7L, one nut.
WARNING Bolts may be of different lengths. Be sure to note their locations.
To install:
  1. Reverse the removal procedure.
  2. The 8.0L engine uses an O-ring to seal. Use a new one and lubricate it with petroleum jelly before installation of the pump. Also, use sealant on the threads of the heater hose pipe, position the pipe as shown before installing the pump and tighten the nut to 12 ft. lbs. (16 Nm).
  3. On pushrod engines, connect the bypass hose to the pump while installing it.
  4. Tighten the bolts to 30 ft. lbs. (40 Nm) on pushrod engines, 40 ft. lbs. (54 Nm) on the 4.7L engine.
  5. Spin pump to ensure the impeller is not rubbing against the timing chain case.
  6. When installing the heater hose pipe, ensure that the slot in the pipe bracket is bearing against the mounting bolt. This will hold the pipe in as far as possible to prevent leaks.
  7. Tighten pulley bolts to 20 ft. lbs. (27 Nm) on V-6 and V-8, 16 ft. lbs. (22 Nm) on the V-10.

zjlimited_368.jpg

Fig. Water pump bolts differ in length; note check location before installation-3.9L, 5.2L, and 5.9L gasoline engine shown

Hope helps (remember to rate this answer).

Dec 30, 2010 | 2000 Dodge Durango

1 Answer

1997 Dakota v8 water pump replacement steps


Hope this helps!

Common Steps
  1. Disconnect the battery negative cable(s).
  2. Drain the cooling system.
  3. Remove the accessory drive belt.
  4. Remove the lower radiator hose (except Diesel).
  5. Disconnect the heater hose from the pump, if fitted.

WARNING Most cooling system hoses use "constant tension" hose clamps. When removing or installing, use a tool designed for servicing this type of clamp. The clamps are stamped with a letter or number on the tongue. If replacement is necessary, use only an OEM clamp with a matching ID.



f90cf3b.gif
Heater hose pipe O-ring (arrow): twist gently when removing or installing; check condition; lubricate with coolant before installing

CAUTION Always wear safety glasses when servicing contact tension clamps.


  1. Always use a new gasket when installing the water pump. Clean mating surfaces thoroughly before installation.
  2. This would be a good time to replace radiator hoses. At least, inspect them carefully for aging or other damage.
  3. If the heater hose pipe was removed, use thread sealant or equivalent on the pipe threads (if threaded), or lubricate any O-rings with coolant before installing.
  4. Check the accessory belt routing against the plate in the engine compartment before starting engine.
  5. Allow the engine to reach operating temperature and check for leaks.

3.9L, 4.7L, 5.2L, 5.9L, 8.0L Gasoline Engines
  1. Carry out the "Common Steps" above.
  2. Remove the upper radiator hose.
  3. Remove the fan and shroud assembly.
  4. On engines except 4.7L, remove the four water pump pulley bolts and remove the pulley.
  5. Remove the heater hose pipe mounting bolt, if fitted.
  6. On engines except 4.7L, loosen the bypass hose clamp at the water pump.
  7. Remove the seven water pump mounting bolts and, on the 4.7L, one nut.

WARNING Bolts may be of different lengths. Be sure to note their locations.


To install:
  1. Reverse the removal procedure.
  2. The 8.0L engine uses an O-ring to seal. Use a new one and lubricate it with petroleum jelly before installation of the pump. Also, use sealant on the threads of the heater hose pipe, position the pipe as shown before installing the pump and tighten the nut to 12 ft. lbs. (16 Nm).
  3. On pushrod engines, connect the bypass hose to the pump while installing it.
  4. Tighten the bolts to 30 ft. lbs. (40 Nm) on pushrod engines, 40 ft. lbs. (54 Nm) on the 4.7L engine.
  5. Spin pump to ensure the impeller is not rubbing against the timing chain case.
  6. When installing the heater hose pipe, ensure that the slot in the pipe bracket is bearing against the mounting bolt. This will hold the pipe in as far as possible to prevent leaks.
  7. Tighten pulley bolts to 20 ft. lbs. (27 Nm) on V-6 and V-8, 16 ft. lbs. (22 Nm) on the V-10.

f56c5d2.gif
Water pump mounting hardware—4.7L


2ae42b0.gif
Use a prybar to keep the water pump from rotating while pulley bolts are removed


61a0d8b.gif
Bypass hose clamp (arrow) must be tended to before removing the pump


a99aab1.gif
Water pump bolts differ in length; note check location before installation—3.9L, 5.2L, and 5.9L gasoline engine shown


2d58c07.gif
After removing the bolts, pull off the pump and place it in a safe location

Apr 18, 2010 | 1997 Dodge Dakota

1 Answer

Water leaking from under the hood by right side of radiator


check the leak if its coming from loose hose clips, bypass pipes, broken radiator, coolant reservoir or from the water plugs in your engine block..

Apr 14, 2010 | 2003 Jaguar X-Type

2 Answers

I am trying to locate the starter of my 1998 LS 400 pls. help me.


The starter is located under the intake manifold on this engine.

20d8b81.gif

Jun 17, 2009 | 1998 Lexus Gs 400

Not finding what you are looking for?
Cars & Trucks Logo

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...