Question about 1993 Toyota Camry V6

1 Answer

I need to know if the water pump freezing up can jar the timing belt loose. 2000 toyota camry le orgifly@yahoo.com

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

The timing belt runs the water pump. If the pump bearing is bad, yes it could cause the timing belt to jump or even strip some of the teeth from the belt.

Posted on Jul 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ?


Where is the crank position sensor on a 95 Toyota celica gt 2.2

search.aibing.cc/Where+is+the+crank+position+sensor+on+a+95+Toyota...
P1335, No Crankshaft Position Sensor Signal - Engine Running. ... 91 1991 ToyotaCelica GTS Engine Mount Right 2.2L 4 Cyl Genuine. ... 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001 . ... Powered by a 2.2-liter engine, the Celica now had ST and GT trim models. ... in 1986 and a 2.0-liter ...

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ...

www.fixya.com/cars/t26080657-crank_position_sensor_1994_toyota
31 mins ago - It is not behind pully nor in dist all videos show - Toyota Cars & Trucks question. ... Change a crankshaft position sensor on a 2000 eclipse.

toyota camry crankshaft sensor - ABMforum.com

abmforum.com/toyota-camry-crankshaft-sensor.html
toyota camry crankshaft sensor 99 camry crankshaftcamshaft position codes i got a problem with my 97 ... The car 96 toyota camry 2.2 liter 4 cyl. ... 1994 toyota camry 2.2L 257k miles Symptoms Car overheats Top radiator hose hot bottom cold ...

Toyota Camry 5SFE Engine Timing Belt, Water Pump and ...

hubpages.com > Autos > Do It Yourself Auto Repair
Jul 10, 2014 - The Toyota 5SFE motor is a four-cylinder, 2.2 liter, timing-belt-driven, double ..... Remove the lower timing belt cover with the crankshaft position sensor. ..... I've never, ever replaced the harmonic balancer on a 4cyl 5SFE.

1995 Toyota Camry LE 4 cylinder - YouTube

? 2:27
https://www.youtube.com/watch?v=7TW6hlUiHWQ
Sep 6, 2011 - Uploaded by jacasan2000

Feb 03, 2016 | Toyota Cars & Trucks

1 Answer

How do i remove timing belt cover on 2000 toyota camry 4 cylinder 2.2 litre? i notice the securing bolts around the perimeter. do i access some of these from the wheel bay?


See here for info, p26 and 242.

http://www.turboninjas.com/camry/eg1.pdf

This is for an earlier year model, but is for the 2.2L engine.

You will have to remove the crank pulley, timing belt covers and timing belt, for best access. Unless it is fairly new, I would replace the belt wile you are at it.

Oct 13, 2014 | 2000 Toyota Camry

1 Answer

I need timing belt marks for new timing belt on a 1994 Toyota Camry LE 2.2L 4 cylinder


Firstly the no.1 piston should be at TDC (compression).

The upper camshaft sprocket has a smaller hole in the web. This should be lined up exactly with the TDC timing mark behind it on the cam bearing cap. In this position it will be vertically upwards.

At the same time the notch in the crankshaft pulley timing flange should be opposite the 0 degrees mark on the timing marks on the front of the lower belt cover.

Nov 12, 2011 | 1994 Toyota Camry

1 Answer

Sir, I have replaced my water pump,and timing belt on my Toyota Camry Le,97,I have tryed to start it but I cannot start it.what could be the problem. John.


check the timing belt it may not been install correctly out of timing make sure the engine is TDC (TOP DEAD CENTER) . Some cases if the belt is not tensioned right it would slip out of timing.

Dec 07, 2010 | 1997 Toyota Camry

1 Answer

How to change the water pump on a toyota camry le 1994 v6


You will need to go through the proceeder that you would to do a timing belt. Remove the drive belts, upper engine mount and bracket,jack the car up and place a jack stand under the car. Remove the harmonic balancer, then both of your timing belt covers. Drain the radiator,and start unbolting the water pump. Loosen the tensioner for the timing belt and remove the belt. You should be able to remove the remainder of the waterpump bolts and replace the pump. I would also recommend that you check your roller bearings,tensioner for any leaks, and replace them all if you have high miles on your car. Parts stores can get you a kit that carries the pump, belt,tensioner,and pulleys if needed.Hope this helps. Might have left out a step or two, but if something is in the way obviously you will have to move it.

Nov 04, 2010 | 1994 Toyota Camry

1 Answer

Is a 2000 toyota camery 4 cylinder a zero


NO, BUT REPLACE TIMING BELT AT 90k AND WATER PUMP, TENSIONER, YOUR CAMRY WILL SERVE YOU WELL

Jul 24, 2010 | 2000 Toyota Camry

1 Answer

Replacing the timing belt and water pump on a 1995 toyota camry le 4 cyl. need to get the drive shaft pulley off. 1st, right or left hand thread on the pulley bolt? 2nd any easy way to get the bolt loose?


Threads are standard. I use a 1/2" drive breaker bar on the bolt. Position the bar so that if you turn it clockwise it will hit the ground or the car frame. Then I turn the ignition to start for just a moment, cranking the engine over with the starter which will loosen the bolt. DO NOT let anyone hold the bar or stand anywhere near it if you try this technique. I have done it many times with no problems.

Mar 06, 2010 | 1995 Toyota Camry

1 Answer

This 200 Toyota Camry LE does the old click, click


check battery connections my be corroded or battery could be loosing voltage over night

Feb 17, 2010 | 2000 Toyota Camry

1 Answer

My 2000 Camry XLE has 130,000 miles on it. I was thinking of changing the timing belt because I don't know if the previous owner replaced it or not, I do not want to take the chance. Can you tell me please...


Timing belt change interval is 75,000 miles.

It's time to change the T-Belt and water pump now.

Water pump is directly behind the timing belt cover.

It's best to get the water pump done at the same time.


Nov 12, 2009 | 2000 Toyota Camry

1 Answer

2001 Toyota Camry 2.2 L rattle near drive belts.


Hello, there are a couple of possible causes, it could be the water pump going out, it is driven from the timing belt, it may be a timing belt idler pulley or a worn drive belt tensioner

Aug 14, 2017 | 2001 Toyota Camry

Not finding what you are looking for?
1993 Toyota Camry V6 Logo

Related Topics:

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...