Question about 2000 Chevrolet S-10

1 Answer

I need the timing specs for a 2000 Chevy S10 2.2

I need the timing specs

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,230 Answers

Hi there, 

Install a scan tool. 
Start the engine. 
Allow the engine to reach normal operating temperature. 
Perform the following checks:
The A/C is Off, if equipped. 
The gearshift control lever is set in Neutral or the manual selector lever is in Park. 
The parking brake lever is fully engaged.
Connect an inductive timing light (2) to the number 1 ignition coil (1) wiring harness. 
Select the Engine Output Controls feature under Special Functions of the scan tool Diagnostic menu. 
TURN ON the Fixed Spark mode with the scan tool. 
Observe that the Spark parameter on the scan tool data list displays 5 degrees , indicating that the Fixed Spark mode has been activated.
Inspect with the timing light (3) that the crankshaft pulley notch (2) lines up with the timing pointer (1), indicating that the timing is correctly set at 5 degrees .
If the timing marks are not correctly aligned, adjust the ignition timing as follows:
10.1. Loosen the camshaft position (CMP) sensor housing bolt (2). 

Rotate the CMP sensor housing (1) clockwise in order to advance the timing. 
Rotate the CMP sensor housing (1) counterclockwise in order to ****** the ignition timing.
10.2. Tighten the CMP sensor housing bolt (2). 
10.3. Review the ignition timing with the timing light as in step 9. 

Repeat step 11 if the timing marks are not correctly aligned. NOTE: Refer to Fastener Notice in Cautions and Notices. 
Tighten the CMP sensor housing bolt (2) to the correct value. Tighten Tighten the CMP sensor housing bolt to 15 N.m (11 lb ft) .


Inspect with the timing light (3) that the crankshaft pulley mark (2) and the timing pointer (1) are still correctly aligned. 
TURN OFF the Fixed Spark mode with the scan tool. 
Observe the timing marks with the timing light. 
The crankshaft pulley mark should now be approximately 13 mm (0.5 inch) to the left of the timing pointer, indicating normal operation.

Good Luck!!

Thanks

Posted on Jul 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the timing for my 2000 chevy cavillier 2.2


Hello mpacovsky: My name is Roger and I will help you. There are no timing specs for your vehicle. Static timing is set when the timing chain is installed. This is the only timing you can do. All advance and retarding is done through the on board computer. The computer controls all of the timing.
Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Sep 08, 2011 | Chevrolet Cavalier Cars & Trucks

2 Answers

Need torque specs for 2000 chevy malibu 3.1 cyl heads & intake


(step 1 ) the torque specs for the heads are---1998 through 2001 are 37 foot lbs. ( step 2) rotate an additional 90-degrees (1/4 turn). intake manifold bolts ( lower ) step 1-- 62 in-lbs, step 2--115 in-lbs. intake manifold bolts/studs ( upper ) 18 ft-lbs. this is for the 3.1 v-6, have a good day!

Aug 14, 2010 | 2000 Chevrolet Malibu

3 Answers

Ignition timing specs for a 1986 Chevy 454?


Automatic I presume. 8 degrees BTDC @ warm & 700 RPM.
distributor vacuum off & plugged. In drive, & accessories off.
Don't forget parking brake on.

Jul 16, 2009 | 1986 Chevrolet Chevy

1 Answer

Need fuel pressure info


fuel pressure specs are as follows:
5.0 &5.7L 60-66 psi
7.4L 55-62 psi

Jul 07, 2009 | 2000 Chevrolet Silverado 1500

1 Answer

Timing specs


72 chevy 3/4 ton this is the original engine what is the timing setting

Jul 03, 2009 | Chevrolet Blazer Cars & Trucks

1 Answer

Torque specs on Chevy Silverado 2500 rear diff yoke.


There isn't a torque spec since those bearing are pre-loaded. You place the unit on a good known vic and get a breaker bar and you might even have to put an extention on that and you begin to tighten unitil you fell the bearing start to load...a little extra short turn wouldn't hurt at that point.

May 07, 2009 | 1977 Chevrolet Silverado 2500

1 Answer

Torque specs for 2000 chevy silverado truck 4.3 v-6 engine


Not sure what torque spec's your looking for.
Go to www.AutoZone.com, enter your vehicle information and check specifications. You should be able to look up the torque spec's your looking for.
Good luck.
Regards,

May 02, 2009 | 2000 Chevrolet Silverado 1500

2 Answers

Torque specs


the center bolt for cv axle!103ft-lbs,hub bearing assembly bolts!77ft-lbs

Apr 26, 2009 | Chevrolet Blazer Cars & Trucks

Not finding what you are looking for?
2000 Chevrolet S-10 Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...