Question about 1996 Nissan Altima

1 Answer

How do you remove rear wheel bearing on a 1996 nissan altima

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 721 Answers

I'm pretty sure they're pressed,so you need to either replace the hub assemby or press the bearing out using a hydralic press.

Posted on Jul 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2009 altima. I hearing a roaring noise


In my 2005 Nissan Altima I experienced a roaring noise from the rear of the car. It ended up being the rear wheel bearings needed to be replaced. It appears that this is a common problem with Nissan Altima's & Maxima's of varying years even with fairly low mileage. This might be your problem.

May 13, 2014 | Cars & Trucks

2 Answers

Procerure to replace wheel bearing assy 2004 nissan altima 4cyl


Go to YOU TUBE and put in replacing wheel bearing hubs for
nissan altima & watch

There is a lot to see even if on a different vehicle

I doubt you have the tools to do the job

Sep 19, 2012 | Nissan Altima Cars & Trucks

2 Answers

Have owned 2 2006 altimas and both have had roaring noise like a wheel bearing going out in right rear


It may be caused by a bad wheel bearing. To be sure, try to swap the 4 wheels and see if there would be changes in the noise location. If it does change, the noise may be from the tires that are not worn out evenly.

Sep 27, 2009 | 2006 Nissan Altima

1 Answer

How to replace a rear wheel bearing 1996 nissan maxima gle


  • Remove tire
  • Remove brake caliper assembly
  • Remove brake rotor
  • Remove hub cap
  • Remove cotter pin
  • Remove wheel bearing lock nut & washer
  • Remove wheel hub bearing from spindle
to install wheel bearing nut torque to 137 Ib to 188 Ib

Sep 26, 2009 | 1996 Nissan Maxima

1 Answer

Noise from rear wheel area that sounds like bearing noise.


Might want to check your camber adjustments and look into shocks and struts. They could all be worn out but prolly the camber is off causing abnormal road noise and abnormal tire wear

Jun 16, 2009 | 2005 Nissan Altima

1 Answer

Steering wheel vibration and whine noise from rear of car


Yes, and it probably is your wheel bearing. Hearing a sound like a chain dragging is classic. You may also hear a clicking noise or chain dragging noise when turning to the left or right.

Look under the car and see if the rubber boots that surround the axle near the tires are cracked and leaking grease. If so, it is almost a certainty that the bearings are bad as you have lost grease and thus lubrication to the bearings.

Good luck,
bob

May 28, 2009 | 2003 Nissan Altima

2 Answers

Humming


It may be the bearing. located underneath the wheel rotor on the wheel axle. Lift up the car and remove the wheel, brake pads and rotor. remove the rotor and turn the nut that holds to axle in place by removing a small pin. (if there is one) and turning counter clockwise. you will see the bearing under the rotor. Check for missing bearings , dirty oil debris, etc. If it has any of this , replace with new bearing. The exact way you removed it. Do not overtighten the nut. This will cause the bearing to overheat. just tighten enough for the bearing to fit snug with no movement.Make sure you grease up the new bearing good.

Dec 16, 2008 | 2003 Nissan Altima

1 Answer

2003 Altima rear end noise


it is either a tire or you have a wheel bearing going bad. sounds like a bad bearing. you can usually narrow down side by driving and turning the side that is bad will get louder when weight shifts to that side and quieter when weight shifts off

Dec 08, 2008 | 2003 Nissan Altima

2 Answers

How to replace front wheel bearings and CV joints on a 1991 Nissan stanza


I can tell you on a 93 Altima that you have remove the entire wheel knuckle and press it out from the rear. Yeah, the knuckle, remove the strut tower bolts, drive train ( which can be lighty pressed out ), caliper and bracket, and remove the ball joint. There's a snap ring at the back of the wheel knuckle that holds the bearing, then press it out with a socket and a table vice or something to that effect. By the way the going commercial rate if you take it to a shop and have them do it starts at $150 for labor. Worth it, oh yeah.

Jul 24, 2008 | Nissan Stanza Cars & Trucks

Not finding what you are looking for?
1996 Nissan Altima Logo

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...