Question about 1986 Chevrolet El Camino

1 Answer

Car will not start after changing negative battery cable

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,055 Answers

Youve got a bad connection,check the boby and engine ground and the battery terminails

Posted on Jul 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change positive battery cable


START BY REMOVING THE NEGATIVE CABLE FROM THE BATTERY. REMOVE THE POSITIVE CABLE FROM BOTH TERMINALS, REPLACE WITH THE NEW ONE. AFTER THIS ONE IS SOLID IN PLACE AND THE CONNECTIONS ARE TIGHT, RECONNECT THE NEGATIVE CABLE.
SEE IN THE OWNERS MANUAL IF THERE IS A RESET PROCEDURE (BATTERY CHANGE).

Jun 18, 2015 | 1997 Mercury Mystique

1 Answer

Changed battery car won't start 2002 highlander


what made you change the battery from the get go? does your car even crank? are you sure you installed the battery correctly, positive cable to positive post and negative cable to negative post. assuming you installed the battery correctly and your car does not start but does crank it may be a fuel or ignition issue. if your vehicle does not even crank you may have a starter issue or no starter signal from the ignition switch to the starter. lastly and highly unlikely is the vehicle factory immobilizer system may have a failure and is not allowing the vehicle to start.

Aug 29, 2014 | 2002 Toyota Highlander

1 Answer

Change battery on 2005 nissan frontier wont start


Hi, If the problem is associated to you replacing the battery, then it could be a few different things. 1) Is the replacment battery fully charged? If not, charge and retry. 2) Are the positive and negative battery cables connected correctly to the battery? With this you have to be sure that you have a good connection to each battery terminal. Try removing the cables and taking a wire brush to the terminals. Once clean, reconnect them and try to start again. 3) Is the positive cable broken? If broken replace the cable. 4) Is the negative battery cable broken or properly connected to the car? If broken, replace the cable. Good Luck!

Jan 11, 2011 | Nissan Frontier Cars & Trucks

2 Answers

Dead overnight battery short in instrument panel


You will need a amp meter to check this. 1. make sure the battery is fully charged 2. remove the negative cable from the battery 3. with the key out of the ignition and doors closed place one probe on the negative battery cable and the other probe on the negative post of the battery (the battery should be in the car with the positive cable attached to the positive battery post) 4. note the amount of amps your truck is drawing (3 is the norm, 5 or more is considered high) 5. if the reading is high remove one fuse at a time, check the amps again until you find which fuse is drawing the extra amps. 6. Start with the smaller fuses; if you suspect it is a problem with the instrument panel start there. This should help you pinpoint your problem area. Good luck

Aug 26, 2009 | 1998 Ford Explorer

1 Answer

Starter motor vw polo gti after long journey did not click over changed starter motor all ok few weeks later after long journey same problem told by mechanic wiring fault starter motor burnt out


REPLACE THE POSITIVE BATTERY CABLE.BESURE TO BUY SOME FLEXIBLE WIRE CONDUIT.PROTECT WIRE FROM RUBBING CAUSING SHORT.ALSO REPLACE NEGATIVE BATTERY CABLE.DUE TO YOUR CAR BEING PCM CONTROL BY DISCONNECTING NEGATIVE BATTERY CABLE WILL CAUSE STARTING PROBLEMS AND STEERING PROBLEMS WITH NEWER CARS WITH ELECTRIC POWER STEERING.LET VOLKSWAGON DEALER REPLACE CABLES AND STARTER.

Aug 25, 2009 | Volkswagen GTI Cars & Trucks

1 Answer

Battery cables FRYED!


Battery cables can be purchased at any auto parts store. Always remove the Negative cable first. The positive cable connects to the solenoid to the starter. After removing both cables, connect the positive cable to eh solenoid to the starter, and route it up to the battery. If the new battery has protective caps on it, leave them on for now. Connect the negative cable to the ground. Connect the positive cable to the battery (remove the caps) Once secure, connect the negative cable to the battery (be very careful not to touch anything metal) IMPORTANT: Make sure the Positve cable is connected tot eh Positeve battery terminal (indicated by the + sign. The Negative cable connects to teh Negative post indicated by the - sign. I hope this answers your question fully and best of luck to you!
Greg

May 15, 2009 | 1997 Chevrolet Blazer

1 Answer

A month ago I bought A used 2000 elantra it used to start fpr the first try In the same time I changed the engine oil and Trying to put a good battery when I finished it did not start.


Verify (test) the battery is good/charged. Verify good, clean cable connections (positive & negative, correct polarity). Inspect positive and negative cables for loosness (positive cable condition to starter connection - clean/tight) negative cable condition to ground connection clean/tight). Replace/repair/clean/tighten cable(s) as needed. Did you remove/disconnect any components from the engine when you replaced the battery? If so, did you remember to put/reconnect them back?

Apr 22, 2009 | 2000 Hyundai Elantra

1 Answer

Temp guage hot & won't start


Simply replacing the battery can NOT cause the problem you describe. I suggest you check the battery cables (polarity) to be sure the battery is installed correctly... then check the battery cables to ensure they are properly connected and no damage is evident (negative - to negative - and positive + to positive +). Replace cables as needed.

Apr 18, 2009 | 1994 Hyundai Excel

1 Answer

Battery grounding problem for ford taurus 98


Either the ground cable is loose or corroded at block connection . If cleaning this does not help, change the cable!

Mar 14, 2009 | 1998 Ford Taurus

1 Answer

2005 battery replacement


Yes you do need to remove the brace "bar" above the battery. If I am not mistaken, the fuse box also has to be relocated for clearance. One thing you must do before you start is disconnect the negative cable from the battery. The negative cable is the black one. One of the oldest rules when working on any vehicle battery is negative is disconnected first and reconnected last. Since the vehicle is "negative ground" it will make it impossible to short negative to ground. The bolts that hold the bar in place are either 13mm or 15mm. The battery is held in place with a plastic wedge that is held down with a 13mm bolt. The battery cables are 8mm.

Jan 04, 2009 | 2006 Pontiac Montana SV6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...