Question about 2002 Saturn L-Series

1 Answer

How to remove # 2 cooling fan - 2002 Saturn L-Series

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,129 Answers

Remove the radiator to access the fan

Posted on Jul 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the fan relay on 1999 aurora located


Cooling Fan Relay No. 1
Center rear of engine compartment, left of the windshield wiper motor
7 - COOLING FAN #2 Relay
8 - COOLING FAN #3 Relay High Speed Cooling Fan Relay #3
9 - COOLING FAN Fuse
60A
Cooling Fan Relay #1, Cooling Fan Relay #2

Apr 18, 2016 | 1999 Oldsmobile Aurora

1 Answer

Remove and replace 2 electric cooling fans in front of condenser coil


THose are not fun. pretty sure you have to remove the grill and loosen the Radiator to sneak them out.

May 18, 2014 | 1994 Mercedes-Benz C-Class

1 Answer

Cooling fan runs continuously, even after shutting the ignition off


sounds like it could be a relay.

With everything plugged in and the fans running with the key off remove the cooling fan 1 fuse. Do they stop?

If they do not stop remove the cooling fan 2 fuse. Do they stop?

Aug 15, 2012 | 2002 Pontiac Montana

1 Answer

Installing radiator


REMOVAL
1. DRAIN ENGINE COOLANT
2. w/ CRUISE CONTROL SYSTEM:
REMOVE CRUISE CONTROL ACTUATOR COVER
3. DISCONNECT ECT SWITCH CONNECTOR FROM FAN SHROUD
4. DISCONNECT ELECTRIC COOLING FAN CONNECTORS
5. REMOVE RADIATOR HOSES
(a) Disconnect the upper hose from the radiator side.
(b) Disconnect the lower hose from the water inlet pipe.
6. DISCONNECT RADIATOR RESERVOIR HOSE
7. A/T:
DISCONNECT OIL COOLER HOSES
8. REMOVE RADIATOR AND ELECTRIC COOLING FANS
(a) Remove the 2 bolts and 2 upper supports.
(b) Lift out the radiator.
(c) Remove the 2 lower radiator supports.
9. REMOVE RADIATOR LOWER HOSE
10. A/T:
REMOVE A/T OIL COOLER HOSES
11. REMOVE ECT SWITCH WIRE
12. REMOVE ELECTRIC COOLING FANS Assembly is reverse order.

Jan 01, 2011 | 1996 Toyota Camry

2 Answers

2002 jeep grand cherokee larado is over heating. The cooling fanonly runs if I hotwire it. I changed th thermostat. Temp gauge is reading . Could it be the cooling fan relay if so where is it located. The...


Fan relay is located under pass headlight. Remove light assembly, use 2 1/2 " hole saw to drill hole in plastic housing ,3"from back wall, 3'' from left side.This will put you right over relay. Unscrew two bolts,replace. Relay was $40.... dealer wanted$350 to remove front bumper to replace it.

Sep 02, 2010 | 2002 Jeep Grand Cherokee

1 Answer

How do you change the cooling fan



Electric Engine Fan

Cooling Fan Connectors

Removal & Installation
2.2L& 2.4L Engines
  1. Disconnect the negative battery cable.
  2. Remove the hood close out filler retainers.
  3. Remove the hood close out filler panel.
  4. Remove the upper radiator mount bolts.
  5. Remove the upper two hood latch support bolts.
  6. Remove the two lower hood latch support bolts.
  7. Raise the vehicle.
  8. Remove the cooling fan mounting bolt.
  9. Disconnect the electrical connector from the cooling fan. Remove the cooling fan assembly.

To install:
  1. Install the cooling fan assembly.
  2. Connect the electrical connector to the cooling fan.
  3. Install the cooling fan mounting bolt. Tighten the bolt to 53 inch lbs. (6 Nm).
  4. Lower the vehicle.
  5. Install the lower two hood latch support bolts. Tighten the bolts to 20 ft. lbs. (27 Nm).
  6. Install the two upper hood latch support bolts. Tighten the two upper hood latch support bolts to 80 inch lbs. (9 Nm).
  7. Install the upper radiator mount bolts. Tighten bolts to 89 inch lbs. (10 Nm).
  8. Install the hood close out filler panel.
  9. Install the hood close out filler panel retainers.
Removal & Installation
  1. Disconnect the negative battery cable.
  2. Remove the hood close out filler retainers.
  3. Remove the hood close out filler panel.
    CAUTION Be careful when you handle a sensor. Do not strike or jolt a sensor. Before applying power to a sensor:
    0e518e2.jpg

    Fig. Remove the hood close out filler retainers and the hood close out filler panel
    1. Remove any dirt, grease, etc. from the mounting surface
    2. Position the sensor horizontally on the mounting surface
    3. Point the arrow on the sensor toward the front of the vehicle
    4. Tighten all of the sensor fasteners and sensor bracket fasteners to the specified torque value.
  4. Failure to follow the correct procedure could cause air bag deployment, personal injury, or unnecessary SIR system repairs.
  5. Disable the air bag sensor.
  6. Remove the upper radiator mount bolts.
  7. Remove the upper 2 hood latch support bolts (2).
  8. Remove the 2 lower hood latch support bolts (4).
  9. Raise the vehicle.

    581eb59.jpg
    Fig. Remove the cooling fan mounting bolt
  10. Remove the cooling fan mounting bolt.
  11. Disconnect the electrical connector from the cooling fan.
  12. Remove the cooling fan assembly.
To install:
  1. Install the cooling fan assembly.
  2. Connect the electrical connector to the cooling fan.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the cooling fan mounting bolt and tighten the bolt to 53 lb inches (6 Nm).
  4. Lower the vehicle.
  5. Install the lower 2 hood latch support bolts and tighten the bolts) to 20 ft. lbs. (27 Nm).
  6. Install the 2 upper hood latch support bolts and tighten the bolts to 80 lb inches (9 Nm).
  7. Install the upper radiator mount bolts and tighten bolts to 89 lb inches (10 Nm).
  8. Engage the air bag sensor.
  9. Install the hood close out filler panel.
  10. Install the hood close out filler panel retainers.
  11. Connect the negative battery cable.
Hope this help (remember comment and rated this).

Apr 14, 2010 | 2001 Chevrolet Cavalier

3 Answers

The cooling fans stop working


check your sensor that controls the cooling fans.may need to be replaced.

Jan 01, 2010 | 2003 Chevrolet Impala

1 Answer

How do i take out a cooling fan out of a intrepid


YOU MUST REMOVE UPPER RAD SUPPORT TO REMOVE COOLING FANS..REMOVE ALL 10MM,13MM HEADED BOLTS..REMOVE 4 HEADLAMP SCREWS..7MM HEAD..THERE ARE 2 PLASTIC RIVETS THAT MUST BE CUT OFF AS WELL..HOOD LATCH CAN STAY WITH SUPPORT,LAY BACK ON TOP OF ENGINE OR REMOVE IT..MARK LOCATION ON SUPPORT..REMOVE 4 BOLTS FROM FAN ASSEMBLY,UNPLUG IT..IT ALSO COMES OUT EASIER WITH UPPER RAD HOSE DISCONNECTED..1 CLIP ON TOP OF FAN HOUSING AS WELL

Aug 31, 2009 | 2001 Dodge Intrepid

1 Answer

RADIATOR REPLACEMENT


  • At the time of installation, please refer to the following items.
  • Start the engine, and check for coolant and A/T fluid leaks.
  • Check the A/T fluid level.
  1. Drain engine coolant.
  2. Canada: Disconnect relay block (for daytime running light system) from battery hold-down clamp.
  3. Disconnect upper radiator hose from radiator.
  4. Disconnect lower radiator hose from water inlet pipe.
  5. Disconnect A/T oil cooler hoses from oil cooler pipes.
  6. Disconnect No.1 and No.2 cooling fan connectors.
  7. Disconnect No.1 Engine Coolant Temperature (ECT) switch wire connector.

  8. Remove radiator and cooling fans assembly.
    1. Remove the 2 bolts and 2 upper supports. Torque: 12.8 Nm (9 ft. lbs.)
    2. Lift out the radiator, and remove the radiator and cooling fans assembly.
    3. Remove the 2 lower supports.
  1. Remove A/T Oil cooler hoses from radiator.
  2. Remove lower radiator hose from radiator.
  3. Remove No.1 ECT switch.

  4. Remove No.1 cooling fan from radiator. Remove the 2 bolts and cooling fan. Torque: 5.0 Nm (44 inch lbs.)
  5. Remove No.2 cooling fan from radiator. Remove the 3 bolts and cooling fan. Torque: 5.0 Nm (44 inch lbs.)
INSTALLATION
Installation is in the reverse order of removal.

Nov 06, 2008 | 1992 Lexus Es 300

Not finding what you are looking for?
2002 Saturn L-Series Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...