Question about 1983 Buick Century

1 Answer

Need to remove transmission - 1983 Buick Century

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 315 Answers

Let us know how it goes.

Posted on Jul 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have pulled trans pan on 1996 sunfire but still dont see shift silinoids.where are they hiding?


Most of the shift solenoids are located under the "side" pan of the transmission, not the underside transmission pan. The side pan is difficult to access and might best be handled by someone who has removed this type of cover before.

Sep 22, 2015 | Cars & Trucks

3 Answers

How to remove and replace auto transmission ?


Its a big job gave you and example for neon

Jan 18, 2015 | 2001 Chrysler Voyager

1 Answer

How to remove1995 cavalier transmission


The transmission is transversely mounted in these vehicles. The mount that secures the transmission to the body is also supporting the engine. If you want to remove the transmission without also removing the engine you will have to support the engine once you remove the transmission mount. You will need to remove the drivers side wheel, caliper, and rotor. You then need to remove the drivers side CV shaft. You will need to separate the lower ball joint in order to remove the shaft and to provide working room to separate the transmission from the engine. You need to disconnect the Shift cable (automatic) or slave cylinder (manual) from the transmission. You must separate the passengers side CV shaft from the transmission, but you do not need to full y remove it. Ensure that you do not separate the inner CV joint when pulling the transmission free from the inner splines. Remove the flywheel shield plate. If automatic transmission, unbolt the torque converter from the flywheel. Disconnect any electrical connections from the transmission. If automatic transmission, disconnect the hydraulic lines running to the radiator. Unbolt the transmission from the engine at the bell housing. Automatic transmissions will come out fairly easy...manuals you must pull back to disengage the transmission splines from the clutch disc.

Sep 07, 2014 | Cars & Trucks

2 Answers

How to replace theTRANSmisson


you need engine support fixture or engine crane, you need basic mechanic tool set. you need floor jack and need jack stands you have to drop subframe.replacing transmission not easy,you need buy a chilton or haynes repair read through transmission removal page you have to remove other parts to remove transmission.

Oct 24, 2012 | 2008 Ford Taurus X

2 Answers

I need steps of removing a transmission from 1981 chevy tow truck


  • Remove the TV cable or transmission throttle cable from the carburetor or throttle body. Remove the upper bolt holding the transmission dip stick but do not remove the tube. Disconnect the negative cable to the battery. Drain the transmission fluid by removing the transmission pan. Replace the pan after draining the fluid.
    Remove the shift linkage and the wires to the neutral safety switch. Remove the speedometer cable by unscrewing the cap at the point it enters the drive gear in the tailshaft. If it has an electronic speedometer, disconnect the electrical connector.

  • Install the engine support stand above the engine. Remove the CV joints. Remove all electrical connectors from the transmission. Remove the bolts in the torque converter. Place the floor jack under the transmission. Raise the transmission just enough to support it. Remove the transmission mounts. Lower the transmission enough to have access to remove all the transmission bolts. On a rear wheel drive vehicle, remove the bolts in the bottom of the transmission mount. Raise the transmission enough to remove the cross member.
    Once the bolts are out remove the cross member and then lower the transmission. Remove the dip stick tube from the transmission by lifting up. If it is hard to come out tap its mounting bracket with something and it will come up and out. Support the transmission securely on the jack. Using a flat head, separate the transmission from the engine. Lower the transmission.

    hope this helps

    but you can also just pull the motor and trans for better access ive also got an 85 chevy im about to do some work on ganna pull and rebuild the motor which is a first for me so if u know any one i could also get some tips from help would be awsome thank you

Nov 10, 2011 | Honda Cars & Trucks

2 Answers

I have a 2002 gmc sonoma need to replace clutch how do i take transmission out.


Not too big of a deal. Disconnect battery.
Remove driveshaft from vehicle. Disconnect any electrical wiring from transmission. Remove starter. Remove gear shifter. Support transmission on a transmission jack, or a good sturdy floor jack. Remove rear transmission mount, and crossmember. Lower transmission slightly to help gain access to the engine-to-trans bolts. Unbolt slave cylinder and hang it out of the way. Remove engine-to-transmission bolts, and bouncer bars (if equipped) Slowly pull transmission away from engine. If it's stuck, double-check to make sure all the bolts are out, then try raising or lowering the trans a bit with the jack and/or pry in between with a pry bar to help break it loose. Remove transmission from vehicle. DON'T lose the dowel pins! They are needed to line up the engine to the trans properly. Remove clutch pressure plate from flywheel, and remove pressure plate, and clutch plate. If the rear main seal is leaking (behind flywheel) NOW is the time to change it (cheap $10 part) Installation is in reverse of removal. Good luck!!

Aug 22, 2011 | 1995 GMC Sonoma

1 Answer

19how do i take out my transmission on a 1997 plymouth voyager mini van ?


remove the air cleaner assembly to remove the upper bell housing bolts.you need a engine support fixture to support the engine,you have to raise van with a lift to support van,besure to remove crankshaft position sensor from the transmission bell housing.you have to drain transmission fluid in a catch pan,remove both front axles.you need transmission jack support transmission.to do this job you will need a haynes repair manual because you have a list of things need to be removed before removing transmission, you need all basic mechanic tool set.

Apr 03, 2011 | Plymouth Voyager Cars & Trucks

2 Answers

I am wanting to install a transmission in a 1998 jeep wrangler se. 4.0 cyl 2.5 liter I will need to take out the old one first. I've never done it before and any help would be great


Instructions vary depending upon if its a stick or automatic transmission. Your best bet if you haven't ever done anything like that is to get yourself a chilton or haynes manual. Both have text and pictures to help with the job. With hanynes, you may need the transmission manual instead of the regular repair one if its an automatic...check the contents before you buy it.
When doing an automatic, it's advisable to remove the crank sensor from the bellhousing as often they get damaged accidentally when working in there. If you need to remove the flywheel, make sure you mark it's position so you can put it back exactly the same way it was installed.
Make sure you have a flat solid area to work on. Transmissions need to be supported so notheing get's damaged. To do that, you need a place where you can move a jack easily. If you need to work on dirt etc, buy a sheet of 5/8" plywood to put underneath.

Mar 25, 2011 | 1998 Jeep Wrangler

1 Answer

How to remove a transmission?


Hope this is not your first, if it is you picked a tough one to learn on. Here goes:1 disconnect negative battery cable 2 Raise and support the car, a lift is the best tool for the job here, but you can do this on jackstands, they just need to be tall ones at least 2 feet of clearance under the car. 3 Install engine holding fixture, this supports the back of the engine when you remove the crossmember and trans.4 remove left front wheel, seperate ball joint remove drive axle retaining nut then remove drive axle from transaxle by prying at joint closest to transaxle. Do not pull on the outer joint or you will pull the inner joint apart. 5 place transmission jack under transaxle pan. 6 remove bolts from crossmember then remove the crossmember 7 remove inspection cover then remove three torque converter bolts 8 remove transmission cooling lines from fittings on transmission 9 remove shift cable 10 unplug 4 wire plug from front side of transmission 11 remove 6 bolts from bell housing 12 remove speedometer cable 13 remove three bolts from around right hand drive axle, then pry axle loose from transmission. You do not need to remove axle from car, just let it hang.14 pull transmission away from engine far enough to disengage the alignment dowels and finish pulling right hand drive axle from transmission housing then lower the transmission to the floor 15 pull transmission from under vehicle.

Mar 16, 2010 | 1998 Chevrolet Cavalier

1 Answer

HOW DO YOU REMOVE MANUAL TRANSMISSION TO REPLACE CLUTCH


You'll need to remove the axleshafts. Remove the battery and tray. Disconnect the clutch and shifter from the transmission. Unbolt the starter from the transmission. Support the motor and place a jack under the transmission. Disconnect the transmission mount. Remove the bellhousing bolts and unplug any connectors, also remove the insepection cover. Seperate the transmission from the motor, move the transmission back to get the input shaft out of the clutch disc and lower the transmission down.

Mar 15, 2010 | 1993 Saturn SW1

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...