Question about 2008 Toyota Sienna

2 Answers

How do you access the rear tail light bulbs to replace in a 2006 sienna van?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

2006 Sienna taillight.
Open tailgate. Loosen bolts holding tailight assembly. Standing next to the car, pull light assembly toward the side and back of the car. It will feel like you're going to break the light assembly, but you won't. I attempted this last fall (2008), but feelin' a bit uncomfortable pulling on it in different directions, I reassembled it and had the guys at the dealership do it right there in the dealership parking lot. If it was to break, I wanted them to break it! But it didn't break and I saw how to do it next time.

Posted on Jul 22, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 89 Answers

U have to remove the two rear panels inside the boot there might be a couple of screws if not just pull panel sharply off that will give u access to them

Posted on Jul 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace toyota sienna brake light - Model 2000


If you are talking about the High Brake Light at the top of the tailgate:

1.) Take out the two Phillips head screws in the lens.
2.) Carefully pry the lens straight back . The gasket sticks to the paint so be careful not to rip the foam gasket.
3.) The bulb is a 921 replacement. Easily found size.

If you're talking about the brake light in the tail light assembly:

The instructions for accessing the tail light are in the Owners Manual. Basically, you have to remove one or two screw/bolts from the inside of the vehicle, then there are two snap type plastic hole/receptacle in the plastic tail light assembly. Be very careful that you pry on the housing in the proper direction, perpendicular to the entry of the snap in connector, or you will break the plastic bayonet or attachment to the lens assembly.

It sounds harder than it really is once you take a look at it. If you have a manual, it will tell you and show you how to get the rear tail lights off easily without breaking any of the plastic connectors. Hope this helps.

Mar 10, 2010 | 2000 Toyota Sienna

1 Answer

How do I access the brake lights on a 2006 Grand Vitara- I want to replace the bulbs but don't know how to access as their seems to be now access from the inside of the car. I am assuming that the bulb is...


well it could be a fuse for the tail lights, but can also be the bulbs,if you open the rear hatch and look on the side ot the lens there you will see two retainers, may be bolts (10mm) or plastic retainers. remove those and light pops out,

Mar 06, 2010 | 2000 Suzuki Grand Vitara

1 Answer

How do I replace a tail light


Not sure if you mean the whole tail light assembly or only the bulb. For either one on that vehicle it should be the same process, more than likely you will have to remove a few screws inside the rear hatch which should allow the tail light assembly to be pulled out. The bulb connector will have a clip or will need turned a certain way to pull the bulb/connecter out of the assembly. Replace the burnt bulb and reassemble. Since I haven't seen the vehicle, there is a chance that is like some cars and the access to change a bulb is accessed from inside the vehicle inside the rear compartments.

Oct 23, 2009 | 2000 Toyota Sienna

2 Answers

How do I replace the Rear Brake light bulb of 2001 Toyota Sienna?


I have a 2001 Sienna and have had to replace most of my tail light bulbs.

The bulbs that are mounted in the fender (wrap arounds) have acess panels in the van's interior that easily pop out and expose the back of the light assembly.

However, the bulbs that are found in the lift gate are a different matter. You have to remove the whole interior panel to the lift gate to expose the light assemblies. Go to your auto parts store and get a tool to help pop out the plastic retainers from the lift gates metal frame. Don't force the retainers out. Go slowly and gently so that you don't damage the interior panel. If you are really gentle you might even get to reuse the retainers.

Good luck!

Jun 08, 2009 | 2001 Toyota Sienna

1 Answer

Remeove rear combination tail light cover 2006 Nissan XTERRA


thode screws hold the lens or the light assembly? Allow for the whole tail light to come out and the bulb plug will be accessible. I never had the privilage. But how the lens fits will tell you. If the lens goes overthe edges, the whole unit comes out, lens is sealed. Good luck

Jun 03, 2009 | 2006 Nissan Xterra

1 Answer

2003 Toyota Sienna - Need to replace left rear brake light


Hi -
I just replaced my left rear brake light on my 2005 Sienna. I followed the manual directions and removed the two metal bolts from the tail light cover. However the assembly did not come off. I could open it a little and it appeared to be bolted from the inside. I looked online but didn't find an answer. I had already gotten pulled over and I didn't want to go to the dealer so I pulled on the assembly a little harder applying even pressure to the top and the bottom and it popped loose. I didn't yank it. There are two metal pegs that have a little lip on them and thats where you are getting the resistance. Hope this helps.

Dec 02, 2008 | 2003 Toyota Sienna

1 Answer

2003 Sienna tail lights don't work when headlights are on


Look under the dashboard, next to/above the park brake pedal, for the interior fuse box. It has a black plastic cover. Remove the TAIL fuse, and see if it is blown. This should get you fixed up. Hope this helps, and Thanks for choosing FixYa.

Nov 11, 2008 | 2008 Toyota Sienna

1 Answer

Tail light


Hi Melony63k,
Open the rear door and look at the back corner of the body where you see under the carpet some eight mm nuts...take those out and the cluster will come off...you can then replace the bulbs....
Regards Johngee10

Aug 03, 2008 | 2001 Toyota Sienna

1 Answer

How do I access the tail light bulbs of a 2006 Windstar?


open hatch remove screws on inner lipe of light if it has no screws the tail light snaps in bulb in rear of light housing

Aug 02, 2008 | Ford Windstar Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...