Question about 1999 Volkswagen Golf

1 Answer

Abs and brake light won t go off please help - 1999 Volkswagen Golf

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 89 Answers

Brake light switch is faulty replace it. abs light will need to go on a computer to find fault

Posted on Jul 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

ABS and Brake Light p1332 1999 volvo c70


What the problem your ABS/brake light is on .......or your code p1332 witch has nothing to do with your brake ...p1332 is a (vvt) variable valve timing

Feb 21, 2015 | 1999 Volvo C70

1 Answer

My 2006 e200k has come with the abs esp warning and says visit workshop. Thereafter the ABS light stays on. I travel from PMB to Durban and I need to drive back to PMB. I drove from PMB with no proble


If the car hasn't gone into "limp home mode" then you should be fine to drive it but go easy on the brakes as there won;t be any ABS to help assist with heavy braking.

Oct 07, 2014 | 2006 Mercedes-Benz E-Class

1 Answer

1999 Windstar drives fine for awhile then something starts to happen the abs light comes on the trak light comes on the lights won't go hi and low no backup lights the turn signal won't turn o


Just as a precaution, please check the brake fluid reservoir on that model. There is a sensor at the base of the master cylinder which can leak brake fluid over the wiring circuit, and cause the electrics to short out. In some extreme cases this has caused fires in some vehicles. This is why Ford had issued a recall to this particular model in the states at least.

Nov 13, 2012 | 1999 Ford Windstar

1 Answer

Abs light stays on and brakes hard to push


Abs which stands for anti brake system has failed. In most cases replacing the control senor for abs will fix the problem. Where it is located on your car i dont know . Call your local autozone and they will help you out... Hope this helps and Please rate this post.

Aug 14, 2012 | 1992 Dodge Dynasty

1 Answer

Gauges dont work abs light on and heater wont turn off


abs light means anti lock brake system and the light is telling you that they aren't working properly. you still have brakes it just won't be with the anti lock system your vehicle has. you will need to have your brake system checked out.

Jun 11, 2012 | 1993 Chrysler Concorde

3 Answers

What does the abs light on mean in a 1996 chevy Corsica


Its the Auto Braking System.
This is the system that pulses your brake to reduce skidding when braking on gravel, ice, wet pavement...etc.
When this light comes on...more than likely it won't function correctly and your tires will lock up and skid.
Fixing the problem usually requires a brake job / brake replacement all the way around.


Hope this helps...

Aug 17, 2011 | 1996 Chevrolet Corsica

2 Answers

ABS light won't go off recently had both front wheel bearings replaced on a 1999 gmc jimmy - the ABS light came on immediately during a test run, i told the mechanic about it and i was told it would...


There are ABS wheel speed sensors on the front wheels behind the hubs. It is possible if the hub where replaced either the pick up ring mounted to the hub itself was not installed or might have purchase non abs hubs or they just did not switch the wheel speed pickup ring on the new hub. Another thing could be either the wheel speed sensors are mis adjusted or when they replaced the hubs they hung the spindle by the abs wire and either pulled it out of socket or messed up the wires internally. Here is a basic abs system http://www.ehow.com/how_8511860_diagnose-abs-brakes.html if you have any other questions please let me know. Also please leave good feedback.

Jun 23, 2011 | 1999 GMC Jimmy

1 Answer

I replaced a cracked rear tail light with an after market new light. Now the brake light won't work but reverse lights and directional signal do. The bulbs are fine as I've moved them around and...



  • If there are no brake lights period the check the stop switch (brake light switch)
  • This is attached to the upper part of the brake pedal itself. Should be a little wire off of it. When that goes bad the brake lights will not work at all.
  • Please note that the fuse for "brakes" is ABS only and has no bearing on the brake lights themselves working.
Regards, Tony

May 30, 2011 | 2003 Jeep Grand Cherokee

2 Answers

1998 GMC Yukon ABS light stays on from start to off the engine


Hello,
It sounds like the wheel speed sensor may have been damaged in the process of removing the tire. That would cause the abs light to come on. Ususaly when the abs light comes on it is a sign they won't opperate as abs but only as standard hydraulic brakes. I hope this helps. If you have more questions reguarding this or other conserns please ask me. Please remember high ratings are very important to me.

Thank You,
Roy

Aug 28, 2009 | 2000 Chevrolet Tahoe

1 Answer

What do i do once i have the codes for an ABS problem?


Are both the the abs light and the brake light on ? Usually indicates A bad abs module under the hood in front of the master cylinder if the abs brake come on for no reason yousally while brakeing at low speeds you will feel the pulsation for a few second this is usually corrosin on the hub bearing or a bad abs sensor in the wheel.. A tech with a good scanner can trace the problem to one specifiac wheel hope this helps...

May 05, 2009 | 2002 Chevrolet Avalanche

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

299 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...