Question about 1999 Chrysler Sebring

1 Answer

Will not start, 1999 sebring LXi coupe

I have changed the distributor, plugs, wires, furl filter, crank shaft sensor, its getting fuel and will turn over but will not start, it will not start even when I put starting fluid into it.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

Check your timing belt and make sure the timing is on right

Posted on Jul 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2000 Nissan frontier runs great for about 15 minutes then starts sputtering tach starts jumping. Changed distributor cap & rotor button plug wires fuel filter & crank shaft position sensor. What...


I would want to monitor fuel pressure as the engine warms up. But it could also be a coil or ignition module problem, even a relay.
Any chance the check engine light is on ?

Jul 23, 2013 | Cars & Trucks

3 Answers

No spark


First does the rotor turn when cranking engine?? possible timing chain is out or stripped gear..are you sure it has no spark??did you verify this with a high output spark tester ? did you spray starting fluid in the tbi unit ?

Mar 23, 2012 | 2000 Chevrolet Astro

1 Answer

I have a mitsubishi colt, and it has problems starting in the mornings. It turns over, but wont start, when I eventually get it started its very lumpy, and when I push the accellerator the engine almost...


There is no simple answer, there are to many variables. If you have access to a scan tool, pulling the codes should help. Without them its back to old school hunt and peck method. At this point we need to narrow down the problem. You need to test for spark.
  1. Tag and disconnect the spark plug wires from the spark plugs.
  2. Remove the spark plugs and install the spark plug wires to each spark plug.
  3. Ground (do not hold spark plug) the spark plug; check if spark occurs while engine is being cranked.
Crank the engine for no more than 2 seconds at a time to prevent flooding the engine with gasoline.
If you have spark, You will want to make sure you have fuel injector pulse, along with fuel pressure. If you have spark ..simply spray some starting fluid in through the air filter and hold the gas pedal to the floor and crank it over while spraying. If it fires up, you know it is fuel related( fuel pump, regulator, or ECM if no injector pulse) . If you have no spark then look at ignition coil connection and trace through to the distributor( if equipped ). The crank shaft sensor has a tendency to fail on these as well. This should give you a few things to test and check to start you on your way to narrowing it down. If you have no spark then look at ignition coil connection for power and trace through to the distributor( if equipped ). If it is DIS( no distributor). It may be the Crank sensor or the ECU. The crank shaft sensor has a tendency to fail on these as well.
The ECU uses the signal sent from the Crank sensor to trigger the spark and fuel injectors. ( make certain you have checked all fuses)

Apr 06, 2011 | 2006 Mitsubishi Colt

1 Answer

My 2003 OZ Rally Mitsubishi Lancer is not starting properly. The engine turns and turns but wont start. especially early in the morning when its colder. later in the day i will start it again and it will...


There is no simple answer, there are to many variables. If you have access to a scan tool, pulling the codes should help. Without them its back to old school hunt and peck method. At this point we need to narrow down the problem. You need to test for spark.
  1. Tag and disconnect the spark plug wires from the spark plugs.
  2. Remove the spark plugs and install the spark plug wires to each spark plug.
  3. Ground (do not hold spark plug) the spark plug; check if spark occurs while engine is being cranked.
Crank the engine for no more than 2 seconds at a time to prevent flooding the engine with gasoline.
If you have spark, You will want to make sure you have fuel injector pulse, along with fuel pressure. If you have spark ..simply spray some starting fluid in through the air filter and hold the gas pedal to the floor and crank it over while spraying. If it fires up, you know it is fuel related( fuel pump, regulator, or ECM if no injector pulse) . If you have no spark then look at ignition coil connection and trace through to the distributor( if equipped ). The crank shaft sensor has a tendency to fail on these as well. This should give you a few things to test and check to start you on your way to narrowing it down. If you have no spark then look at ignition coil connection for power and trace through to the distributor( if equipped ). If it is DIS( no distributor). It may be the Crank sensor or the ECU. The crank shaft sensor has a tendency to fail on these as well.
The ECU uses the signal sent from the Crank sensor to trigger the spark and fuel injectors. ( make certain you have checked all fuses)

Nov 02, 2010 | 2003 Mitsubishi Lancer

1 Answer

02 Mitsubishi Galant, changed igniton but now wont start


There is no simple answer, there are to many variables. If you have access to a scan tool, pulling the codes should help. Without them its back to old school hunt and peck method. At this point we need to narrow down the problem. You need to test for spark.
  1. Tag and disconnect the spark plug wires from the spark plugs.
  2. Remove the spark plugs and install the spark plug wires to each spark plug.
  3. Ground (do not hold spark plug) the spark plug; check if spark occurs while engine is being cranked.
Crank the engine for no more than 2 seconds at a time to prevent flooding the engine with gasoline.
If you have spark, You will want to make sure you have fuel injector pulse, along with fuel pressure. If you have spark ..simply spray some starting fluid in through the air filter and hold the gas pedal to the floor and crank it over while spraying. If it fires up, you know it is fuel related( fuel pump, regulator, or ECM if no injector pulse) . If you have no spark then look at ignition coil connection and trace through to the distributor( if equipped ). The crank shaft sensor has a tendency to fail on these as well. This should give you a few things to test and check to start you on your way to narrowing it down. If you have no spark then look at ignition coil connection for power and trace through to the distributor( if equipped ). If it is DIS( no distributor). It may be the Crank sensor or the ECU. The crank shaft sensor has a tendency to fail on these as well.
The ECU uses the signal sent from the Crank sensor to trigger the spark and fuel injectors. ( make certain you have checked all fuses)

Jul 01, 2010 | 2002 Mitsubishi Galant

1 Answer

TWO DAYS AGO 94 RANGER (4 CYL) SOHC...STOPPED ON ROAD. CRANKS BUT DOES NOT START. HAS FUEL PRESSURE. CHANGED FUEL FILTER. CHANGED AIR FILTER. CHANGED ONE OF THE DISTRIBUTOR COILS...TWO SPARK WIRES WERE NOT...


If all the coils are giving spark now,then you moat likely have gas fouled plugs now,so change them out with new ones,all 8 of them.If you do not have spark on all plug wires,pull the timing belt cover,and align the cam shaft and the cam,to see if the belt has jumped.If It hasn`t,replace the crankshaft sensor.

Oct 17, 2009 | 1994 Ford Ranger Supercab

1 Answer

I have a 1991 740 volvo, was driving down he street and it died,after i pulled over it wouldn't start


Check if you still getting fuel and sparks, two items need to keep the car running. Check fuses and fuel pump relay, if needing new relays go to the junk yard and get couple of them for nothing. Checking making sure you getting fuel and fuel pump working properly, unplug the the main coil wire to distributor so the car wont start we just want the engine just to turn over. under the hood, locate fuel filter, disconnect the line to or from it, wrap the bottom of the hose with old clothe firmly and to remember to point the house downward away from your face so it wont splash at you. and have a friend turn ignition over just like starting, see if the fuel come out with good pressure. if fuses and relay check out, your crank sensor may be bad, being 91' strong possibility. crank sensor send info to computer telling to send fuel to your injectors. For sparks, make sure you plug the main wire to distributor back. pull one plug wire and get spare plug, plug it and ground the plug and have a friend turn the engine over and see if you getting sparks, do not touch the plug, big shock. No sparks, check the coil if you getting 12v, if yes, than your cam sensor is faulty. The cam sensor work just like the crank sensor but telling the computer to send sparks to the distributor. Common for older European cars, crank and cam sensor tend to become faulty after years of service due to age and heat abuse.

Aug 09, 2009 | 1991 Volvo 240

1 Answer

Stopped while driving replaced fuel filter and pump and crank shaft senor


I suspect you have a bad camshaft sensor. It is part of the distributor. To check, remove distributor cap and rotor (1 screw for rotor) and check for brown dust. If yes, remove slotted wheel and clean optical sensor. If car starts, you need a distributor.

Crank sensor has no affect on system. It is used for back up only.

Can you hear pump run for 5 seconds when you turn key on?

go here for expert villager help and info

http://autos.groups.yahoo.com/group/villagerquest/

May 28, 2009 | 2000 Nissan Quest

Not finding what you are looking for?
1999 Chrysler Sebring Logo

Related Topics:

432 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...