Question about 2003 Toyota Corolla

1 Answer

Bleed brakes on 2003 toyota corolla

I changed front calipers and rear wheel cylinders as well as brakes. I tried pumping brake pedal so I could bleed them. Pedal will not become 'good' pedal for me to bleed them. Since I lost fluid on all four brakes, do I need to do something special (master cylinder, etc)to get a good pedal to bleed brakes?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Toyota Master
  • 905 Answers

I try to help you, firts refill brake fluid container,open purge valve in one wheel front only,wait few minutes when drops fluid, close this valve and open other wheel, same procedure, finally repeat this in each 4 wheels

Posted on Jul 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have replaced 3 disc brake calipers on my 2001 pt cruiser. after bleeding all 4 brakes 3 times, I started the car and brake pedal goes to floor. is my brake booster shot?


Michael:

You must start bleeding the brakes at the wheel farthest from the master cylinder (usually the right rear), then the next farthest from the master cylinder, then the next, then the closest. If your master cylinder is at the left front of the car, start with the right rear, then the left rear, then the right front, then the left front. If you don't bleed the brakes in the correct order, you are just shifting the air in the lines from one line to another. Make sure that you close the bleeder before letting the brake pedal up, and the engine should not be running when you bleed the brakes... Make sure that the emergency brake is off. Make sure that the master cylinder does not run out of brake fluid at any time that you are bleeding the brakes.

Jan 24, 2016 | 2001 Chrysler PT Cruiser

1 Answer

How do I fix the brakes in my 99 Toyota Corolla? I have no brakes and the pedal goes right to the floor.


have you adjusted the rear brakes correctly ( drum brakes)
if not drums then you have air in the systems still
brake bleeding is done starting at the wheel with the longest line and ending at the shortest line
It is a 2 person operation unless you have a pressure bleeder pump attached to the reservoir
your problem is air in the system

Jan 07, 2016 | 1999 Toyota Corolla

1 Answer

I have a low brake pedal on 2003 toyota 4runner


Did you also change the brake pads? Add fluid to top of reservoir?

Was the brake pedal low before you changed the calipers or is this something that developed after you worked on the car? If it was there before the caliper change then it has nada to do with the work you did.

U might have a bad master cylinder.

Nov 12, 2015 | 2003 Toyota 4Runner

2 Answers

I have a 2004 Land cruiser and changed the right rear brake cyl and brake shoes . What is the proper procedure to bleed the rear brake system. Thank you for your help.


  1. Check the fluid level in the reservoir after bleeding each wheel. Add DOT3 fluid, if necessary.
  2. If the master cylinder was disassembled or if the reservoir becomes empty, bleed the air from the master cylinder as follows:
    1. Disconnect the brake lines from the master cylinder.
    2. Slowly depress the brake pedal and hold it.
    3. Block off the outlet plug with your finger, and release the brake pedal.
    4. Repeat 3 or 4 times.

  3. Bleed the brake starting with the one furthest from the reservoir and then the next furthest, etc.
  4. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down.
  5. At the point when fluid stops coming out, tighten the bleeder plug to 11 Nm (8 ft. lbs.), then release the brake pedal.
  6. Repeat until all the air in the fluid has been bled out.
  7. Repeat the procedure to bleed the air out of brake line for each wheel.
  8. Check the fluid level and add DOT3 fluid if necessary.

Aug 07, 2011 | 2004 Toyota Land Cruiser

2 Answers

I changed the front brake pads and now have no pressure when i press the brake peddal. the master cylinder is full but still no pressure. what did i do wrong?


You may not have done anything wrong. You won't have any pressure the first couple of times that you press the brake pedal. Try pumping the brakes a few times. When you change the pads you have to open the caliper all the way up to get the caliper back on. When you press the brake the pads won't go all the way to the caliper on the first couple of times you press the brake. But once you pump the pedal, it should build up pressure. If not you will have to bleed the brakes.

Nov 29, 2010 | 1995 Toyota 4Runner

1 Answer

2003 rav 4, just replaced front calipers and pads, after bleeding the line,peddle was spongie, bled all four lines, peddle still spongie, do I need the engine running to properly bleed the lines, and since...


I would bleed the rears too especially if the brake fluid reservoir drained empty. Also you may need to drive the vehicle to seat the brake pads. Check and see how the pedal feels initially before you road test to make sure you don't need to pump the brakes in order to stop. if you do then re bleed all four wheels.If you don't have to pump the pedal and it just feels spongy then try going around the block a few times and see if the pedal stiffens up after the pads have seated.

Oct 11, 2010 | 2003 Toyota RAV4

3 Answers

Brake fluid is not going thru on new calipers. got new calipers from napa not dealer.


did u bleed the brakes ? there could be an air bubble causing blockage

Sep 29, 2010 | 2001 Jeep Grand Cherokee

1 Answer

How to bleed brakes on 2002 toyota sienna


Here is the procedure from the service manual. I would add just one thing. Do each wheel in this order

  1. right rear wheel
  2. left rear wheel
  3. right front wheel
  4. left front wheel
BLEEDING

HINT: If any work is done on the brake system or if air in the brake lines is suspected, bleed the air from the system.

NOTICE: Do not let brake fluid remain on a painted surface. Wash it off immediately.


a)FILL BRAKE RESERVOIR WITH BRAKE FLUID Fluid:SAE J1703 or FMVSS No. 116 DOT3

b)BLEED MASTER CYLINDER HINT: If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

c)Disconnect the brake lines from the master cylinder. SST 09023-00100 Slowly depress the brake pedal and hold it.

Block off the outlet plug with your finger and release the brake pedal.
Repeat (b) and (c) 3 or 4 times.


BLEED BRAKE LINE

1. Connect the vinyl tube to the caliper or wheel cylinder bleeder plug.
2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down.
3. At the point when fluid stops coming out, tighten the bleeder plug, then release the brake pedal. Torque: (Bleeder plug) Front brake caliper
: 8.3 Nm (85 kgf-cm, 74 inch lbs.) Rear wheel cylinder: 8.5 Nm (87 kgf-cm, 75 inch lbs.)
4. Repeat (b) and (c) until all the air in the fluid has been bled out.
5. Repeat the above procedure to bleed the air out of the brake line for each wheel.

CHECK FLUID LEVEL IN RESERVOIR Check the fluid level and add fluid if necessary. Fluid: SAE J1703 or FMVSS No. 116 DOT3

Jun 25, 2010 | 2002 Toyota Sienna

1 Answer

Got answer to my question about air in brakes but how do you bleed the master cylinder?


to bleed the brake line somebody as to pump the brake pedal
3 to 4 times and somebody opens the bleeder on the brake caliper

starting by the right rear wheel, then the left rear wheel, then front right wheel anf finishing with the front left wheel bleeder.

to bleed the master cylinder is the same principle pump pedal 3,4 times
but this time open the line at the master cylinder starting with the rear hoses

hope it is helpful

Jul 08, 2009 | 1999 Cadillac DeVille

2 Answers

I need to know how to bleed the brakes on a 1999 chevy blazer


Start from right rear, then, left rear, right front, left front. Fill master cylinder. Have helper sit in car, have helper hold brake pedal down. open bleed screw. fluid and air comes out. close screw. release brake pedal. Continue until no air comes out. Move to next wheel. Keep an eye on master cylinder fluid level after each wheel.

Mar 27, 2009 | 1999 Chevrolet Blazer

Not finding what you are looking for?
2003 Toyota Corolla Logo

618 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...