Question about 1993 Ford Mustang

1 Answer

1993 5.0 convertable. Drivers seat leans back on in board side. removed from car and could not find any broken parts. losened covers and inspeced frame aswell.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 103 Answers

See if floor pan is cracked,seat frames do crack on these, inspect better around welds and riveted areas. see back rest frame too for cracks

Posted on Jul 14, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Broken driver's seat G6 2007

Ours finally brok and had to remove it to get it welded... weird flaw

Jan 10, 2013 | 2007 Pontiac G6 GT Convertible

1 Answer

Remove front seat from 2005 ford five hundred

Move the seat all the way forward and remove the two bolts going into the cross bar in the back. Move the seat all the way back and remove the plastic covers where the front feet of the seat meet the floor. Remove the two bolts going into the floor. Lean the seat back and disconnect the electrical connectors.Lean the seat sideways so that the outside part is facing up and remove the nut holding the seatbelt to the seat and take off the seatbelt. The seat is now free to be removed from the car.

Nov 28, 2012 | Ford Five Hundred Cars & Trucks

1 Answer

Front seat of 1993 crown vic is loose or broken

look under seat and u will ee the rails on each side of seat rock seat back and forth to locate wich bolt is loose or broken or if the rail itself is broken if rail broken remove the seat and order or go to a junkyard for the rail

Mar 02, 2012 | 1993 Ford Crown Victoria

1 Answer


Under the seat there is supposed to be a cable that runs from one side to the other. It releases the other side to move. It is come off or broken.

Aug 11, 2011 | 1993 Saab 900

2 Answers

Where is the fuel filter and pcv valve on a 1993 G20 van

PCV valve located under engine cover, top of engine, mounted in passenger side valve cover

Fuel filter is located Under vehicle, passenger side, below seating area, front of fuel tank, mounted on chassis DON'T FORGET TO RATE THIS POST!!

Aug 23, 2010 | 1993 Chevrolet G20

2 Answers

2004 Malibu with broken weld on seat motor

you will have to replace the complete assy. the cheapest way is look for a complete wrecking yard seat, or have yours welded at a local machine shop

Jan 08, 2010 | 2004 Chevrolet Malibu

1 Answer

Pull latch on spare tire carrier is broken

Don't know this car, but should be not very much different:

No entire spare tyre there as common today I believe but a so called home comer.

Fixed back down under in the back boot, with a wooden ply board cover?
One bolt to fix her down is common.
Probably you are talking that you can not open the boot because hatch near driver seart is broken or the lock on your boot. Experienced that.
Then you have to struggle in by clapping rear seats down
Get all out and .
Most unwise is to free/ cut the points to which that boot board is hanging.

Now you can't Move the key to open the boot
to fix any rear lock problem. This problem is not the lock mostly (unless you already tried lubing that lock) but the cable coming from front drivers side that unlatches from the inside. It neds to be made moveable again.
Crawling in is a bit dificult to do so.
If only the handle is broken at drivers side, get access at that point by removing the seat (4 bolts I think, Have to shift that seat a bit to retract all four) Try to get now to that mechanism there and fix or replace what is broken. I doubt that the cable itself to the rear is broken.

If that car is in good shape, undoubtedly (only 2001) better have a mechanic at a dealer do it the fastest cheap way, since he has the fastest trick and the original part. If kept well these cars are to last 200.000 miles and 15 years easily. If you maintain them properly. Before becoming an independent brand, KIA has been an outstanding assembling contractor for bigger brands on the market.

So don't break anything you regret later.
Mostly these problems arise from not greasing, lubricating and cleaning the mechanisme.

May 02, 2009 | 2001 Kia Sephia

1 Answer

Driver side seat back is loose

Sounds like your latch is broken. You can replace the latch, it is spring loaded .Once you remove the trim around the latch and pull the seat cover up you can gain access to the bolts. You will need a torx bit ,I believe a t40 not sure. 13mm and 15mm socket.

Jan 26, 2009 | 1999 Ford Explorer

1 Answer

Driver side front seat back bends

The seat back frame is broken, in most cases it can be welded but all the trim must be removed and the seat dis-assembled down to just the frame, any upholstery shop can do this job for u, about $100-200

Dec 02, 2008 | 2000 Ford Focus

Not finding what you are looking for?
1993 Ford Mustang Logo

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers


Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides