SOURCE: burned out headlight/bulb bmw 1991 325i 2dr
It's a bulb replacement. If it's anything similar to my Audi, there is a cover on the back of the headlight housing that you pop off. Then you can reach in, pull the wire connector off the bulb, and unclip a metal retainer over the bulb, and pull the bulb out. Installation of the new one is the reverse. Just be SURE not to touch the glass part of the bulb. Skin oils can cause a halogen bulb to burn very hot and burn out very quickly. If you do touch the glass, wipe it gently but thoroughly on a cotton cloth to clean it off before you install it.
SOURCE: low beam headlights not working on 2004 Pontiac Montana extended
You headlight lamp have a diffuser mechanism which allows it to flip between the hight beam and low beam feature of the bulb. In fact, you high beam will function even if the low beam is not working.
I would recommend the purchase of the new headlight lamp. It would cost you you any where from $15.00 per unit to get a replacement lamp
SOURCE: my passenger side low beam headlight is out. the
Check the fuse. There are seperate fuses for right and left. You dont mention if the high beam works for that side? If it does, the fuse is good. The GREEN wire at the bulb is the ground for the low beam. If that wire has power, then the ground is bad. If the high beam works, the hi'lo beam switch is good, and there is a problem between that headlight and the Engine Compartment Junction Block
SOURCE: Low Beam Drivers Side doesn't work ... low voltage,
Power for the headlights on the Left side (High and low beam.) comes from the same fuse... The ORANGE wire and the ORANGE/BLACK are the same, they connect in the harness. If you only lack the 12v to make the light work connect them at the headlight assembly.
If your low beam also lacks ground the Left low beam ground is shared with the right low beam ground... Run a wire from left low beam DARK BLUE to right low beam DARK BLUE/WHITE.
If its not working now then your cursed, seek a witch doctor.
SOURCE: Audi A4 2002 Low beams & Right front turn signal stopped working
but on 2002 A4, F20 and F21 are empty! Does anyone has an idea where the headlight fuses located?
http://repairhelpcenter.blogspot.com/2012/01/passenger-side-low-beam-out.html
------------
Low beam HID light goes out?
http://schematicsdiagram.blogspot.com/2012/01/low-beam-hid-light-goes-out.html
----------2007 Dodge Caliber: Low Beam Headlight Not working
http://technoanswers.blogspot.in/2012/06/2007-dodge-caliber-low-beam-headlight.html
-------------Chevy Tahoe: Low Beam Lamps are not working?
http://technoanswers.blogspot.in/2012/04/chevy-tahoe-low-beam-lamps-are-not.html
----------2001 Chevrolet Tahoe: Both Low Beam Lamps Not Working?
http://technoanswers.blogspot.in/2012/04/2001-chevrolet-tahoe-both-low-beam.html
--------------2002 Toyota Tacoma: Low Beams not working?
http://technoanswers.blogspot.in/2012/04/2002-toyota-tacoma-low-beams-not.html
-----------Low beam headlights Modification?
http://schematicsdiagram.blogspot.in/2012/04/low-beam-headlights-modification.html
-----------DRL and Low beams not working?
http://schematicsdiagram.blogspot.in/2012/04/drl-and-low-beams-not-working.html
-----------These will help.Thanks.
332 views
Usually answered in minutes!
The high beam on the drivers side will not light up...I used a meter and it is not gettin power on the high beam side...any ideas...thank you...
Thank you...did that...same thing...where could the problem be in the wirin...also the clear lights in the bumper don't work on high or low beam...I put a meter on them too...no power...are they spose too...are those called ditch lights...thank you...
Ok...did a little research... I have read it could be the dimmer switch...can any one confirm that...also...does any one know what the part # is fur the dimmer switch...thank you...
Why dont you bring 12 volts too light thats not working and if they work then you have too trace wiring back
Evenin...I figured this problem out a couple of weeks ago...then got busy and didn't make it back...sorry...I did some tracin...and made it back to the blinker switch...I puled off and sanded the points...bam...the high beam has been workin ever since...sorry again it took so long with the switch...thank you fur ever ones help...
×