Question about 2005 Chevrolet TrailBlazer

1 Answer

Where is the cam and crank sensor located at?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

4.2 liter engine

Crankshaft postion sensor: Lower left side just in front of the bell housing. 1 bolt holds it in the block.

Camshaft position sensor. Front of engine, just under the valve cover, right side(passenger) mounted diagonally. 1 bolts holds it in the head.

Posted on Jul 14, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
blueextc3221
  • 15935 Answers

SOURCE: Need to find Camshaft position sensor and crank se

CRANKSHAFT SENSOR - Under hood, center, front engine area, rear of crankshaft pulley, mounted in timing cover assembly.

afa767f.gif
CAMSHAFT SENSOR - Under hood, passenger side, upper engine area, mounted on engine in front of camshaft.
4c3af2b.gif
Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on Apr 08, 2009

  • 16 Answers

SOURCE: where are the cam sensor and crank sensors located on my car?

Crank Sensor: Passenger side of transmission just to right and above the differential cover. Has 3 wires:

Light Blue/Dark Blue stripe - Signal
Dark Red - 8v supply
Black/Light Blue stripe - Ground

If the car runs or cranks, you can test this sensor by first checking for power on RED wire with key ON. Should be 8-9.5 volts DC. Furthermore, connect a dwell meter to the signal wire by probing the back of the connector. Dwell reading should be 49-51%. If not, its likely bad.

If you remove the sensor, you MUST replace the paper spacer on the end of the sensor or you risk damaging the sensor or even the torque converter drive plate otherwise. Also make sure O-ring is in good shape and positioned properly.

Cam Sensor:
Facing Engine, it is on the driver side timing case housing, on top of the round part, just to the right of the fuel rail pipe where there is a capped fuel valve.

Has 3 wires:

Tan/Yellow stripe - Signal
Dark Red - 8v supply
Black/Light Blue stripe - Ground

Testing is same as for Crank Sensor.

Posted on May 21, 2009

  • 153 Answers

SOURCE: 95 eagle vision esi, where is the crank sensor

The Crankshaft Position Sensor is mounted on the transmission bellhousing

Posted on Oct 05, 2009

csmock132
  • 4669 Answers

SOURCE: 2001 dodge 3500 van cam position sensor location

Crank sensor is in the bell housing of the transmission. Cam sensor is in the distributor.

Posted on Jul 25, 2010

kalei02EXC
  • 62 Answers

SOURCE: 2005 ford excursion cam sensor location

On my 02 Excursion with the 7.3L Diesel, the Cam Position Sensor is located at the front bottom of the engine on the passengers side. There is one electrical pigtail plug that is attached and one bolt holds the sensor in position. It may be located in a similar location on your 05 Ex. I do not know where the crank sensor is located. I hope this helps.

Posted on Sep 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I find the crank sensor on a 2009 Nissan Titan v8 truck?


i think it's the starter. On most nissans, the starter and the crank position sensor are close to each other. Some nissans have 4 position sensors, between crank sensor, crank angle sensor, cam position sensor, and sensor sensing sensor, oh and cam angle sensor. Oh wait, maybe it's a bad ground. Nope, gotta be the staerter.
25440212-xipalmoknr3fbjmp51kycajc-3-0.jpg

25440212-xipalmoknr3fbjmp51kycajc-3-1.jpg

Feb 17, 2015 | Nissan Cars & Trucks

1 Answer

1999 tahoe crank/cam sensor?


the 5.3 and 6.0 are famous for bad crank sensor. never a problem with cam sensor. the crank sensor is located behind the starter. you need to remove starter to get to it. ther is one bolt holding it in. check the wires going to the sensor because they are so close to the exhaust the get brittle and brake. if the wire is good change sensor and your car will run fine

Mar 21, 2013 | 1999 Chevrolet Tahoe

1 Answer

Location of cam and crank angle sensor in 96 N15


The cam and crank position sensor can be found in the front of the crank on the engine block below or next to the water pump in many applications.
It can also be located on the main crank pully or the flywheel.

Feb 09, 2012 | Nissan Pulsar Cars & Trucks

1 Answer

Where is your cam position sensor located? and where is the crank shaft position sensor at?And could you send a diagrm or something to show?


the cam sensor is located on top of the engine in the front of the left side valve cover. the crank sensor is located on the right side of the engine block just above the starter.

Jul 17, 2011 | 2000 Chrysler Concorde

1 Answer

I NEED TO KNOW THE LOCATION OF THE CAM SENSOR AND CRANK SENSOR ON MY 1999 DODGE INTREPID 2.7 LITER


Cam sensor is right in front under the planum and crank sensor is by the crank harmonic balancer pully. But why do you ask?

Mar 03, 2011 | Dodge Intrepid Cars & Trucks

1 Answer

Where is the cam sensor located on a 99 pontiac grand am 2.4 litre? also where is the crank sensor located?


They are located as follows: the cam sensor on the 2.4 engine is mounted on the side of the front camshaft, right next to the fuel rail you will see the wires following to it and the crank sensor is located right above the oil filter on the engine. Hope this helps

Jan 19, 2011 | Pontiac Grand Am Cars & Trucks

2 Answers

Where are the cam & crank position sensors for a 1999 chevy suburbon 5.7?


THE crank sensor is located at bottom of timing cover on front of engine if you look under engine below crank pulley around oil pan timing cover you will see it. the cam sensor is in the distributor.

Dec 22, 2010 | 1999 Chevrolet K1500

1 Answer

2001 dodge 3500 van cam position sensor location


Crank sensor is in the bell housing of the transmission. Cam sensor is in the distributor.

Jul 25, 2010 | 2001 Dodge Ram 3500 Truck

1 Answer

Location of cam sensor


Cam Sensor is on the top of the Water pump located on the Front Timing cover. the Crank sensor is located rear the engine almost on the flywheel.

May 15, 2010 | 2000 Land Rover Range Rover

2 Answers

2005 ford excursion cam sensor location I need to change the cam sensor and the crank sensors on my excursion and i do not know where they are located


On my 02 Excursion with the 7.3L Diesel, the Cam Position Sensor is located at the front bottom of the engine on the passengers side. There is one electrical pigtail plug that is attached and one bolt holds the sensor in position. It may be located in a similar location on your 05 Ex. I do not know where the crank sensor is located. I hope this helps.

Aug 27, 2009 | 2005 Ford Excursion

Not finding what you are looking for?
2005 Chevrolet TrailBlazer Logo

486 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...