Question about 2000 Isuzu Rodeo

2 Answers

Cannot get the rear discs off my 2000 rodeo for a brake and disc change. everything is off, they will not slide off.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,114 Answers

Sometimes the disc will rust onto the hub. Spray the hub/disc mating surface with penetrating oil. Then a few hits with a dead blow hammer around the disc should free it. If you also spray the wheel lugs, clean them off with brake cleaner after. They should not be lubricated.

Posted on Jul 14, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 28 Answers

Check the specs,sometimes even though the front rotors slide off ,the rear rotors may be of a different design and you may have to take out the center bolt to get them off.If thats not the case then you may need a rotor removal tool.There should be a couple of threaded holes somewhere on the throat of the rotor,the tool will bolt into those holes then there will be a center bolt that you will tighten against the bearing bolt,as you tighten this up it should pop off the rotor.

Posted on Jul 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2000 ford mustang gt v8 make a sweeky noise in the rear tires after even after changing rear brakes and shocks.


The squeaky noise can be several things, but usually it's how your pad contacts the rotor provided it's rear disc. Check the caliper slides, if it's not sliding back and forth, you'll wear the inboard side pad and it will squeak.

Oct 15, 2014 | 2000 Ford Mustang

1 Answer

Rear bearing


Remove the rear wheel, if the vehicle has rear disc brakes remove the brake caliper and brake rotor, If the vehicle has drum brakes , slide the drum off. Remove the 4 hub mounting bolts located on the back side of the backing plate.Using a hammer tap on the hub assembly (near the wheel studs) Reverse the steps to install the new hub assembly.

Jun 11, 2013 | Cars & Trucks

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

There is a knock in the rear brakes which stops when you apply the brakes. I took the passenger side tire off and inspected the brake. The outside pad is loose and the inside pad is so tight against the...


It sounds like the slide pin in your brake assembly has jammed - this is a reasonably common problem. The brakes should 'self-adjust' or centre so that there is even braking force from either side. It may be possibly to remove your brake caliper, unjam the slide, lubricate it and reinstall it. At this point you really need to replace your pads and check your discs for uneven wear and have them machined or replaced as necessary. However, it is far more likely that it will be cheaper and easier to simply replace the caliper (and the pads and discs as required).
Hope this helps, Sherwin

Sep 05, 2010 | 2000 Mazda 626

1 Answer

How do remove rear rotors on 2004 ford sport trac


Caliper removal

  1. Disconnect the brake hose.
  2. Remove the bolt.
  3. Disconnect the rear wheel brake hose (2A442).
  4. Remove the copper washers and plug the brake hose.
  1. s2r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
--------------------------------------------------------------------------------------------
Disc Removal and Installation
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and retract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. s2r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc. For additional information on machining brake discs, refer to Section 206-00 .
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.
---------------------------------------------------------------------------------------------
Installation
  1. s2r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
    NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
    NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
    Install the rear disc brake caliper.
  1. Install the rear wheel brake hose.
    • Connect the brake hose and install the caliper flow bolt.
      • Use new copper washers.
  1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
  1. Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Verify correct brake operation.

Dec 17, 2009 | 2004 Ford Explorer Sport Trac

3 Answers

Rear brake pads wear out every 30000 miles on 2002 3/4 tod hd , rotors are pitted bad


That's to be expected and is completely normal.

Rear brake shoes as fitted to drum brakes can typically last up to 60k miles with periodic adjustments, but you have rear disc brakes and the shoes will typically last half of that.

Also, modern brake pads no longer contain asbestos and are now made using harder metallic compounds; the direct result is that brake discs (US=rotors) are also considered to be consumable items as they are worn down by the harder pads. It's not unusual to have to replace front discs every other pad change and rear ones with every pad change; in both cases the mileage will typically be around 30k miles on most models.

Nov 15, 2009 | 2002 GMC Sierra 2500HD

3 Answers

How do i remove the rear rotor on a 2000 ford explorer xlt


  1. Disconnect the brake hose.
  2. Remove bolt.
  3. Disconnect the rear wheel brake hose (2A442).
  4. Remove the copper washers and plug the brake hose.
  5. Disconnect the brake hose.
    1. Remove bolt.
    1. Disconnect the rear wheel brake hose (2A442).
    1. Remove the copper washers and plug the brake hose.
      syn~us~en~file=dh0472a.gif~gen~ref.gif
    1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
      Remove the rear disc brake caliper (2552).
      1. Remove the brake caliper bolts (2W303).
      1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
      syn~us~en~file=gh0619a.gif~gen~ref.gif
    1. Inspect the rear disc brake caliper for leaks.
      • If leaks are found, disassembly is required. Refer to Caliper in this section.
      syn~us~en~file=gh1478a.gif~gen~ref.gif
    Installation
    1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
      NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
      NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
      Install the rear disc brake caliper.
      syn~us~en~file=dh0528a.gif~gen~ref.gif
    1. Install the rear wheel brake hose.
      • Connect the brake hose and install the caliper flow bolt.
        • Use new copper washers.
      syn~us~en~file=gh0621a.gif~gen~ref.gif
    1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
    1. NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.
      Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
    1. Verify correct brake operation.
  6. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.
--------------------------------
Installation
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
    NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
    NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
    Install the rear disc brake caliper.
  1. Install the rear wheel brake hose.
    • Connect the brake hose and install the caliper flow bolt.
      • Use new copper washers.
  1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
  1. NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.
    Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Verify correct brake operation.

May 06, 2009 | 2000 Ford Explorer

1 Answer

Rear brake rotor replacment


206-04: Rear Disc Brake 2000 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  2. Disconnect the brake hose.
  3. Remove bolt.
  4. Disconnect the rear wheel brake hose (2A442).
  5. Remove the copper washers and plug the brake hose.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.

Mar 28, 2009 | 2000 Ford Explorer

1 Answer

Rear axle is bent


Go-To Car-Part.com
http://www.car-part.com/
Type the year (2000), and make (Honda Passport).
Search for Axle Assy Rear
Ignore 4x4 and focus at 4x2.
You must know the ratio - teeth (41/10 teeth, GT5) or (43/10 teeth, S7C)
(3.2L, 6 cyl, disc), 4x2 (drum brakes), 4.10 ratio (41/10 teeth, GT5)
(3.2L, 6 cyl, disc), 4x2 (drum brakes), 4.30 ratio (43/10 teeth, S7C)
1999 - 2002 Isuzu Rodeo - Honda Passport.
You can get an USED one for $600 plus shipping.
Good Luck.

Jan 04, 2009 | 2000 Honda Passport

Not finding what you are looking for?
2000 Isuzu Rodeo Logo

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...