Question about 1997 Buick LeSabre

1 Answer

Easiest way to change out a alnernator on v6 - 1997 Buick LeSabre

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Just do it. If you find this hard get a mechanice

Posted on Aug 26, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I am going to change my spark plugs on my 1999 pontiac grand am V6 engine. I have the socket wrence and spark plugs. But I need to know the easiest way to change the rear 3 plugs.

There is a tool you can get on the internet or from
a tool supplier, to replace the front engine strut/
support, whatever it's called,you can look that up,&
it pulls the engine to the front,so you can sort of
get to the back plugs

Jun 12, 2011 | 1999 Pontiac Grand Am GT

1 Answer

Changed alnernator 3 times after a week of driving battery goes dead agin

Assuming none of the alternators were bad

Have you done any testing, of anything, at all?

Have you removed the fuses one at a time ,to see
if a module wasn't timing out?

You need an AMP Meter, put in one of the battery
cables, to watch for current load.

Mar 03, 2011 | 2003 Ford Focus

1 Answer

Where is the water pump located and how do u change it on a 1996 oldsmobile cutless ceria sl with a 3.1L v6

That is probably the easiest water pump in the world to change. It is right on the front of the engine. Just remove the serpentine belt, remove the bolts from the water pump pulley and remove the pully, Remove the bolts from the water pump and remove the water pump from the vehicle. Reverse steps to install....Good Luck!

Feb 27, 2011 | Oldsmobile Cutlass Ciera Cars & Trucks

1 Answer

Two problems, when the vehicle sits overnight battery dies. battery is 4 yrs old, and test'd alt'nator/battery. no answers as what to do next

this could be one of two problems one ur alternator may not be charging it or has a low charge to it ot two with youre battery being that old its probalbly sulfated by now which means even if youre alnernator is working properly youre battery wont hold the charge try replacing the battery first tho

Feb 15, 2011 | 1996 Ford Bronco

1 Answer

Need to change the flywheel and what is the best way to get to the top 2 trans bolts? 1995 blazer 4x4 vortec v6

if you dont have a long extension and swivel sockets. the easiest was is from the top side down. sometimes removing the distributor will help gain access. there will be smaller nuts holding brackets on the bell studs you will need to remove first.

Nov 26, 2010 | 1995 Chevrolet Blazer

1 Answer

WhaT IS THE EASIEST WAY TO CHange the back spark plugs on a 2005 chevrolet equinox?

The easiest way to change the back plugs on a GM V6 is to pay someone else to do it. You need good light, good tools, lots of various extensions, swivels, and universals. A good vocabulary of curse words also comes in handy.

Oct 03, 2010 | 2005 Chevrolet Equinox

1 Answer

How do you tell the difference between the two engines?

The easiest way to tell is that on the Duratec 3.0 V6 the spark plugs are mounted in the valve cover into the heads. On the Vulcan 3.0 V6 that are mounted under the valve cover in the heads.

Jun 12, 2010 | 2004 Ford Taurus

1 Answer

I need a spark plug wiring diagram for a 1992 Toyota Camry, 4 cylinder, 2200 motor.

I believe your firing order is 1-3-4-2. You may see a number 1 on the distributor cap on this vehicle. That is the #1 plug wire. The wire hole next to that would go to spark plug 3 etc. Easiest way is to change wires one at a time. Hope this helped.

Mar 29, 2010 | 1992 Toyota Camry V6

1 Answer

Easiest wat to change thermostat on freelander v6 es

there isnt any easier work , these are a burden of my life lol , the manifold is not to bad to remove , take your time when refitting and make sure you dont over tighten manifold bolts

Oct 07, 2008 | 2002 Land Rover Freelander

Not finding what you are looking for?
1997 Buick LeSabre Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts


Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides