Question about 2002 Nissan Sentra

3 Answers

Brakes brake pedal goes to floor,brakes are good

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 40 Answers

You have a leak in the hydraulics either a ruptured brake line or abad master cylinder or rear wheel cylinder.

Posted on Jul 26, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 146 Answers

If your brake linings (pads and/or shoes) are in good condition and your pedal is going to the floor, there is either air in the system or you have brake fluid loss. If your booster was bad you would have a hard pedal. Remove all wheels and check for brake fluid loss. Brake master cylinder could also have a loss of fluid through the seal at the back and filling the booster with brake fluid. Remove the two bolts holding the brake master cylinder and inspect for fluid loss. If no loss of fluid, bleed entire system.

Posted on Jul 26, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Bad power booster

Posted on Jul 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Brakes,pedal goes to floor ?


Check your brake master reservoirr,if empty,then you ha ve a leak.

Oct 22, 2016 | Cars & Trucks

1 Answer

My brake pedal goes to the floor but i did not lose brake fluid


The rear brakes could need adjusted or replaced.. Also the master cylinder could have blown a seal.

Jan 30, 2015 | 1999 Pontiac Sunfire

2 Answers

Brake squishy pedal goes to floor


might be a frozen caliper piston or a lot of air in lines

Apr 13, 2014 | 1997 Subaru Legacy

1 Answer

F350 brake pedal goes to floor, whinning sound


they use the power steering pump to power the brake booster so check the level of the power steering

Oct 14, 2012 | Cars & Trucks

1 Answer

When bleeding brakes have good pedal with engine off. with engine running pedal goes almost to the floor what is wrong


can you here a hissing sound when you push the brake while its running? if so then you have a bad brake booster, need to replace it, the hissing is actually the vacuum that builds within the booster escaping thru the seal in the booster

Sep 09, 2012 | Oldsmobile Intrigue Cars & Trucks

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

Brake pedal goes to the floor


check vacumn and\or connections to the vacumn boost cannister.

Apr 21, 2010 | 1985 Ford F150

1 Answer

Brakes spongy after shop replaced rotors braked pads on 2001 buic


Sounds like air is still in the brake lines, the air sound that you hear is the power assist, but the brake pedal needs to be "high and hard".

if the pedal goes to the floor, that is not good. Sometimes, when pumping brakes for bleeding purposes, the master cylinder gets damaged, as the piston goes past it's normal "travel zone" and gets damged on deposits.....

Now, with that being said, if everything was perfect, brakes are typically not as firm after replacement, due to differences in new pads/shoes and old rotors and drums. Pedal to the floor, however, is never okay.

Doc

Sep 18, 2009 | 1995 Chevrolet Blazer

2 Answers

97 ford e350 brake pedal goes to the floor...


are your rear drums set up? why did you bleed the brakes. when only when you installed new pads?

Sep 11, 2008 | 2002 Ford E350

Not finding what you are looking for?
2002 Nissan Sentra Logo

573 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...