Question about 2003 Ford Focus

1 Answer

How much is it going to cost to have a water pump replaced in my 2003 ford focus?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

It depends on certain mechanic shops. of course the dealer is always way higher. estimated 1 1/2 to 2 hours to put on depending if you have to pull off the timing belt. cost will be estimated about 250.00. call around some mechanic shops and see. some will be different than others.

Posted on Jul 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ho w to reset timing, tensioner let go on DOHC


follow this link to a u-tube video ,also take his advice and change the water pump as well unless its alraedy been done recently
How to replace water pump timing belt on Ford Focus

May 22, 2014 | 2000 Ford Focus

1 Answer

No heat after replacing a water pump on a 2008 Ford Focus


You may still have air in the coolant system. Bleed the coolant and watch to make sure it dont overheat. Also turn the heater to full and set it on high while adding and bleeding the coolant system.

Jul 20, 2012 | 2003 Ford Focus

1 Answer

I need to know how to change a water pump in a 2003 ford focus s/w it has a 4 cyl 16 val ztech eng


To change the water pump you need to remove the serpentine belt, remove the pulley from the water pump, rotate the water pump within the housing and replace it. Reinstall, check for leaks.

Mar 26, 2011 | 2003 Ford Focus

2 Answers

Hi! I have a 2003 Ford Focus se 2.0 with a little over 100k miles. A few weeks ago, it started having a "clicking" sound. I can't seem to tell exactly where it's coming from. I have tried changing the...


I am having the same problem. I don't want to go to the dealer because they will charge me way too much just to look at it. I also have a 2003 ford focus se 2.3 pzev. Clicking sounds happen in first gear only.

Aug 06, 2010 | 2003 Ford Focus

1 Answer

I have ford focus 2003 i want to change water pump


you have remove the accessories belt the plastic covers the spark plugs the valves cover the timing belt the pulleys then the pump.after that all back again retiming the engine etc etc........is very difficult procedure for a user.only an experianced person with special tools can do that.

Apr 24, 2010 | 2003 Ford Focus

2 Answers

Does anyone know when the water pump usally needs changing on ford focus 1.4 2003


Water pumps generally do not need routine replacement. A good sign is leakage og coolant. Any detrimental wear such as a bearing will cause leakage of the seal.If it is a precautionary thought, Change it around 75,ooo miles. FGood luck, Ned

Aug 26, 2009 | 2003 Ford Focus

1 Answer

I replace water pump and i time it just by the manual but wont start on ford focus 2003 2.0L


The design of the ford focus is pretty bad. If you didnt do the timing perfect the pistons will hit the valves. This is called a zero clearence engine. You need to check compression in the cylinders and make sure they are in spec.

May 10, 2009 | 2003 Ford Focus

1 Answer

Water pump


About 8, if you are methodical you should be ok. You will probably have to remove the cam belt. If you do you need a tool to hold the cams-the tool is basically a flat plate +/- 400 mm long and about 6mm thick which slots into the rear of the cams when engine is in the correct position and on tdc.

Jun 09, 2008 | 2003 Ford Focus

Not finding what you are looking for?
2003 Ford Focus Logo

Related Topics:

598 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...