Question about 1997 Infiniti.5 J30

1 Answer

How to replace right brake light? - 1997 Infiniti.5 J30

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Should be able to remoce the panel in the trunk exposing the wiring and area that the bulbs connects. Twisting the bulb will release it. install new bulb and twist back into place.

Posted on Jul 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 99 Toyota camry n brake light is on after changing right front brake caliper


Master cylinder fluid piston has entered into a brake safe mode.
when the high pressure brake system is opened in any way, the brake master cylinder piston reaches to the far end of the master cylinder which trips the brake system warning light.

This brake light condition is due to sudden loss of brake fluid pressure on the right front brake caliper assembly during the replacement.

Left rear brake caliper bleed valve will ned to be "opened" until master cylinder piston travels into the opposite direction which "resets" the brake system warning light.

Dot 4 brake fluid recommened for most, but not all vehicles.
Reference vehicle to owners manual for replacement fluid is replaced under master cylinder brake system cap.

Aug 18, 2013 | 1993 Buick Park Avenue

1 Answer

Brake light and turn signals


check to see if the wire connector is plugged in properly

May 30, 2013 | 2003 Jeep Liberty

1 Answer

1997 nissan pathfinder le 3.3l - Brake lights won't turn off - replaced stop switch and relay combo already. any ideas?


The brake switch will stop all current to the brake lights. As soon as the brake pedal moves just off of its fully up position, the switch makes contact and passes current on to the brake lights. You can operate it by hand to check if everything is right. izzit adjustable? The switch is the last thing in the path to the brake bulbs, so it has to work right, right off the brake pedal!

Sep 29, 2012 | 1997 Nissan Pathfinder

1 Answer

Brake light, reverse light and turn signal issues


Hello. The symptoms you are describing are likely due to a poor ground. Temporarily install a new ground wire by securing a piece of copper wire to the frame with a self tapping screw. Use this ground wire along with the hot wire to see if each of these lights works. If it does, trace the ground wire back to the frame, unscrew it and clean up the metal with emery cloth so you reestablish a good ground.

Jan 28, 2010 | 2003 Ford Windstar

2 Answers

I have a 92 s-10 blazer, brake lights an running lights dont work


i just recently replaced my brake lights and running lights

are you sure you wired everything correctly?
check again especially your grounds

Jul 26, 2009 | 1992 Chevrolet S-10

1 Answer

When braking, green turn signal lights up and right rear brake light does not come on. (have replaced brake light)


Do you have a trailer harness? If so, your harness has a short in it.
Remove it and throw it away; cheaper to replace it than to repair it.

If not, you have a short in the socket at the brake lamp

May 04, 2009 | 2008 Toyota Sienna

1 Answer

Which fuze works the right brake light


If the right brake light is the only one not working, the fuse is okay.
There are not seperate fuses for brake lights and work on a single brake circuit. Chances are the bulb is out. Check the bulb and replace as needed with the same type bulb. If it still is not working after the bulb is replaced, check the power and ground circuits with the correct testing equipment.

Apr 20, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Brake lights blows fuse right away


I had the smae problem, i replaced the tail light circuit board and the problem was solved.

Mar 03, 2009 | 1999 Chevrolet Suburban

1 Answer

Right tail light not working when pressing brake w/ lights on.


There should be at least 2 bulbs in the light assembly. One light is the light that is on when you turn on your headlights with out the brake pressed, the other light only lights up while you press on the brake. Make sure you are replacing the correct bulb. You may have been replacing the bulb that stays on. Your lights may be set up to turn off the light that stays on when the headlights are on while pressing the brakes.

Nov 13, 2008 | 1993 Toyota Camry V6

1 Answer

2005 vw beetle


replace the bulb it is a double bulb so it will still work on tail lights but not brake lights replacing the bulb should correct this

May 25, 2008 | 2005 Volkswagen New Beetle Convertible

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14195 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...