Question about 1995 Mercury Villager

1 Answer

Have a bumping noise in the front, what could it be? I changed the struts already.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,124 Answers

Could be a warn bushing in the front end
or could be a ball joint..
Jack up the front end safely - so the wheels are hanging free..
Wiggle each front tire left to right and look & listen for play & noise..

Hope this helps !!
Rate me good ;o)

Posted on Jul 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front Strut Bushings


He's probably talking about upper strut mounts/bearing plates or the rubber bumpstops under them. Either way, the strut assemblies have to be removed and dis-assembled to replace them. So he is probably figuring on replacing these items as well as the struts themselves, since everything is already apart. unless the van has very, very low miles. I would double check the front sway bar links though. These cause noise on bumps similar to a strut mount, and are notorious for premature failure. Moog makes them with grease fittings to get batter life. Both sides can usually be replaced for around $250 for parts and labor. When I do have one with bad strut mounts, I usually go ahead and figure worst case. I figure struts, upper mounts/bearing plates, bump-stops and bellows, and the sway bar links on any T&C with over 60K. Usually runs between $750 - $850 for parts and labor (including alignment) with a labor rate of $74.50 per hour. If it is your struts and not just the sway bar links, you can drive it for a while before they have to be replaced. Another option is complete strut assemblies from Monroe or KYB. They are completely assembled with all new parts and you can bolt them in youself to save come money. It takes all the specialty tools out of the job. This can be accomplished at home with simple hand tools in the driveway! Either way, check the sway bar links. If in doubt, replace them.

Oct 02, 2012 | 2005 Chrysler Town & Country

1 Answer

Clicking noise in front end of car when going over bumps


Probably the front struts your sway bar links can cause the same noise if they are failing but you should have heard or felt somthing while turning regardless of bumps if the sway bar links were bad. Like the other people said start with the struts.

May 28, 2012 | Cars & Trucks

2 Answers

I have a dodge magnun and have replaced the front linkage to sway


check the frunt break pads if the pads were ever replaced by aftermarket pads they will make a clunk sound going over bumps

Jul 10, 2010 | 2005 Dodge Magnum

1 Answer

When I drive slow over bumps/speed bumps I hear a noise in the right front wheel well. The car does not seem take bumps well but seems to be better going over them at higher speeds. Shocks? Struts?...


It could be a bad Shock/Strut, Ball Joint or a bad CV Axle. Put the car on a lift and try to move the parts around to try to isolate the noise.

Jun 24, 2010 | 2003 Oldsmobile Alero

1 Answer

Front suspension noise-dull rattle-thumping sound,bumpy roads


look at the front lower engine mount. I had similar noise which has been driving me nuts, thought may be thesway bar links, put it on friends hoist and saw that the front engine mount (mounted to bottom of lower radiator support) was cracked and the rubber bushing inside very worn with pieces missing. odd thing is that reving, or putting into gear never caused it to make a noise, just certain bumps. I ordered part from Autozone,hopefully it gets here before the holiday week end is over.
Good luck

May 15, 2010 | 2005 Dodge Caravan

2 Answers

Front driver side suspension knock over bumps


See if you can bounce car and replicate the noise. If you can, you should be able to find it, and put your hand on it. Stabilizer bushing are a place to look, both at the lower a arm and on the frame. If you narrow it down to the strut, it will need to be replaced. The front trans mount also goes bad, try putting it in drive with your foot on the brake and give it some gas and see if the engine moves an excessive amount.

Nov 23, 2009 | 1992 Buick Regal

1 Answer

A popping noise when I hit a bump or hit the brakes


Sounds like you need new front struts since it sounds like it is coming from under your or towards the center of the car it most likely is either the driverside front strut or strut housing. I would take it to a certified safety mechanic asap. It might just be worn struts but it could be alot worse then that. Better safe then sorry.

Jan 08, 2009 | 2001 Chrysler LHS

Not finding what you are looking for?
1995 Mercury Villager Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...