Question about 1994 Toyota Paseo

1 Answer

Im replacing a valve cover gasket,I was needing to know what the torue settings and sequence how to tighten the bolts down

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 92 Answers

Not really a sequence just tighten them evenly and the final torque is 61 in. lbs.

Posted on Sep 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need the torque spec for the valve cover on a 06mercury malin


There is a torque spec for the cylinder head; I don't know of one for the cover.

Jul 14, 2015 | Cars & Trucks

2 Answers

How do you Replace Head Gasket for 2002 Nissan Sentra GXE ?


Big difference between valve cover gasket and head gasket. To replace head gasket, you must dissamble top end of engine and send the head out to be resurfaced and then install new head gasket. If it is a leaking valve cover it is much easier. Simply dissasemble and then clean valve cover and top of head from all debris and remove all old gasket material. Tighten back down in sequence and do not over tighten. these small bolts can be overtightened easily so go in sequence just like when you tighten lug nuts by skipping one as you go around. 10mm bolts require about 10 pounds or less torque.

Jul 18, 2014 | 2002 Nissan Sentra

1 Answer

Need picture of valve cover


Should not matter. Just snug them down all around, then tighten them securely. DO NOT over-tighten. You can bend or break the valve cover or the bolts. Do not get crazy when tightening them. Good luck.

Apr 17, 2014 | 2005 Chevrolet Aveo

1 Answer

Plugs getting wet with oil


Don't know what type motor you've got, but this same thing happened with a DOHC Saturn engine. In the inside of the valve cover there's an O ring in each spark plug hole, they need to be replaced. If this is the problem, you'll want to replace the valve cover gasket as well. Since you'll already have the valve cover off. Also when replacing the valve cover, be sure to tighten the valve cover bolts in the proper sequence and proper torque.

Feb 17, 2013 | Cars & Trucks

2 Answers

I have a 1999 Mitsubishi Galant and need to know how to put on a valve cover gasket. Oil is leaking out and dripping and it's causing it to burn and smoke comes out of the car.


Instructions
    • 1 Allow the car to cool. Disconnect the battery terminal. Remove the right side vent screen top extension. Disconnect the ignition coil with power transistor and its wiring and brackets.
    • 2 Disconnect the left hand side coil wires and spark plug wires. Remove the spark plug wires, valve cover bolts and the valve cover. Unplug the electrical connections from the intake manifold runner control actuator. Unfasten the actuator retaining the screws, right bank heated oxygen sensor front and rear.
    • 3 Remove the heated positive crankcase ventilation (PCV) valve. Remove the heated oxygen sensor plug and the Differential Pressure Feedback EGR (DPFE) sensor. Disconnect the ignition coil with power transistor and its wiring and bracket. Remove the valve cover bolts, the valve cover and the old valve cover gasket. Clean the valve cover seating area with automotive engine cleaner and place the new gasket in the gasket seating area.
    • 4 Replace the parts that were removed and disconnected by reversing the steps. Replace the valve cover gasket and tighten the bolts, in sequence, ensuring not to over tighten. Put back the ignition coil with power transistor and its wiring and bracket, the heated positive crankcase ventilation (PCV) valve, the heated oxygen sensor plug and the Differential Pressure Feedback EGR (DPFE) sensor.
    • 5 Add oil to the car. Start the car and let it run at idle for a while to check for leaks..

Aug 18, 2011 | 1999 Mitsubishi Galant

1 Answer

I need to know the torque specs for the head gasket for a 99 2.2 pontiac sunfire


Install cylinder head bolts finger-tight. New cylinder head bolts are recommended due to stretch of the old bolts.
Tighten bolts in sequence, tighten the long bolts to 46 ft. lbs. (63 Nm) plue 90 degrees. Tighten the short bolts to 43 ft. lbs. (58 Nm)


Install pushrode and rocker arms and rocker arm nuts. Tighten nuts to 22 ft. lbs. (30 Nm).


Install valve cover and tighten bolts to 89 inch lbs. (10 Nm).

Apr 05, 2011 | 1999 Pontiac Sunfire

1 Answer

Replacement of timing belt on 2001 daiwoo legansa


This should give you a clue as to how to replace the timing belt on the camshaft pulleys.prev.gif next.gif Camshaft and Valve Lifters REMOVAL & INSTALLATION 1.6L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Timing belt
    • Crankcase ventilation tube from the valve cover
    • Spark plug cover bolts and the cover
    • Camshaft Position (CMP) sensor connector
    • Spark plug wires from the plugs
    • Valve cover nuts, washers, cover and gasket
    NOTE: Be very careful not to nick or scratch the camshafts.
  4. Hold the flats of the intake camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  5. Hold the flats of the exhaust camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  6. Mark the camshaft cap locations so that they may be returned to their original positions.
  7. Remove the camshaft cap bolts in the sequence illustrated.
  8. Remove the caps and the camshafts. Fig. 1: Loosen the camshaft cap bolts in this sequence using several passes - 1.6L engine 9307zg85.gif
    To install:
  9. Lubricate the camshafts and caps with engine oil.
  10. Install the caps and the camshafts in their original positions.
  11. Tighten the camshaft cap bolts in the sequence illustrated to 12 ft. lbs. (16 Nm). Fig. 2: Tighten the camshaft cap bolts in the sequence illustrated using several passes - 1.6L engine 9307zg84.gif

  12. Measure the camshaft endplay on both camshafts. The endplay should be 0.003-0.009 in. (0.10-0.25mm).
  13. Install the intake camshaft gear. Hold the flats of the intake camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 49 ft. lbs. (67 Nm).
  14. Install the exhaust camshaft gear. Hold the flats of the exhaust camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 49 ft. lbs. (67 Nm).
  15. Apply a small amount of gasket sealer to the corners of the front camshaft caps and to the top of the rear valve cover-to-cylinder head seal.
  16. Install or connect the following:
    • Valve cover, washers and nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
    • Spark plug wires to the plugs
    • Spark plug cover and bolts. Tighten the bolts to 27 inch lbs. (3 Nm).
    • CMP sensor connector
    • Crankcase ventilation tube to the valve cover
    • Timing belt
2.0L and 2.2L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Timing belt
    • Crankcase ventilation tube from the valve cover
    • Spark plug cover bolts and the cover
    • Spark plug wires from the plugs
    • Camshaft Position (CMP) sensor connector
    • Valve cover nuts, washers, cover and gasket
    NOTE: Be very careful not to nick or scratch the camshafts.
  4. Hold the flats of the intake camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  5. Hold the flats of the exhaust camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  6. Mark the camshaft cap locations so that they may be returned to their original positions.
  7. Remove the camshaft cap bolts in several passes of one half turn each in the sequence illustrated.
  8. Remove the seal ring from the camshafts. NOTE: Make sure the camshafts detaches evenly from the bearing seats in the front guide bearing.
  9. Remove the caps and the camshafts. Fig. 3: Remove the camshaft cap bolts in several passes of one half turn each in the sequence illustrated - 2.0L and 2.2L engines 9307zg38.gif
    To install:
  10. Lubricate the camshafts and caps with engine oil.
  11. Install the caps and the camshafts in their original positions.
  12. Tighten the camshaft cap bolts in the sequence illustrated to 71 inch lbs. (8 Nm). Fig. 4: Tighten the camshaft cap bolts in the sequence illustrated using several passes - 2.0L and 2.2L engines 9307zg37.gif

  13. Measure the camshaft endplay on both camshafts. The endplay should be 0.0015-0.0056 in. (0.040-0.144mm).
  14. Install the intake camshaft gear. Hold the flats of the intake camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 37 ft. lbs. (50 Nm), retighten the bolt an additional 60 degree turn and finally an additional 15 degree turn.
  15. Install the exhaust camshaft gear. Hold the flats of the exhaust camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 37 ft. lbs. (50 Nm), retighten the bolt an additional 60 degree turn and finally an additional 15 degree turn.
  16. Install or connect the following:
    • Valve cover, washers and nuts. Tighten the nuts to 71 inch lbs. (8 Nm).
    • CMP sensor connector
    • Spark plug wires to the plugs
    • Spark plug cover and bolts. Tighten the bolts to 27 inch lbs. (3 Nm).
    • Crankcase ventilation tube to the valve cover
    • Timing belt
    • Negative battery cable

Feb 04, 2011 | 2001 Daewoo Leganza

2 Answers

Valve cover is leaking oil on my 2000 1.9 TDI Passat. Have changed the gasket but still leaking badly. Have been told to change whole cover but VW want £120,00 Any ideas?


will try to help.if it's only the valve cover leaking,i'm guessing they sold you the rubber one that says ne rtv sealant needed. take your back off, try not to break the rubber seal when removing!clean the top of head where gasket goes. clean the valve cover really good!clean the grooves out that the gasket slides into. buy some blue trv glue, apply a thin coat to top of head, let it setup while you apply another thin coat to valve cover, let set 10mins. apply gasket to valve cover making sure to push the gasket into the grooves on valve cover. don't worry about neatness. let the valve cover set on a hard surface with the gasket against the hard flat surface[such as a garage floor,or clean driveway] after10 more minutes install the valve cover,make sure and take your time. place valve cover onto motor,than hand start each bolt to insure thay are going into the prope bolt holes. after you have each bolt hand started, start at center of valve cover snugging the bolts down to motor. do not crank down or apply excessive force when tightening those bolts. you should see some of that blue rtv glue coming out around the valve cover when applying torque to the valve cover bolts. only secure them snug at first. let car set for 15mins. start car and look for leaks around the cover, do not over tighten those bolts but you may need to look for a leak, go to bolt closest to leak and turn it 1/4 at a time until leak stops. but if you do this step by step, you'll not have a leak issue. you may have pinched the gasket when you replaced it. hope this helps and thank you for choosing fixya.com

Dec 27, 2010 | Volkswagen Passat Cars & Trucks

3 Answers

Oil leaking from valve cover gasket


Oil sending unit is it hard to replace?

Aug 15, 2010 | 1993 Plymouth Sundance

1 Answer

What is the valve cover torque sequence for a 2000 nissan altima


No spec for torque. Bolts have shoulders. Replace gasket. Tighten the 2 center nuts first and just tighten the rest until they stop. You can tighten one and jump across the valve cover and do the other, but not necessary.

Sep 27, 2008 | 2000 Nissan Altima

Not finding what you are looking for?
1994 Toyota Paseo Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...