Question about 1999 Daewoo Lanos

2 Answers

Immobiliser is not turning off and not allowing the engine to start

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Daewoo Master
  • 450 Answers

Is it a stick immobiliser?
If your vehicle does not start and the LED continues to flash while the Ignition is 'ON', this means that the Immobiliser system has not recognised the transponder stick.
Simply turn the Ignition 'OFF' then back 'ON' again. If the Status LED continues to flash, move the transponder stick closer to the key barrel until the LED stops flashing and turns 'OFF'.
If the transponder stick on the key ring does not disarm the immobiliser or the
transponder stick is misplaced, you can override the system by entering a 5-digit override number. Each vehicle has a unique 5-digit override number. This number is recorded on the
customer’s owner’s manual. If the customer loses their owner’s manual / override number, the number can be found by locating the vehicle’s Daewoo Stock Number (D.S.N). The customers override number is the last 5 digits of their D.S.N.
immobiliser is not turning off and not allowing - 9748811.jpg
Overriding the system using the example 5 digit code 2,1,0,6,2
Important Note: 10 flashes of the Status LED represent the number ‘0’.
1. Remove the Transponder from the Key Ring.
2. With the system armed (LED flashing slowly) Turn the ignition ON/OFF 5 times, with the final position being off.
3. The LED will turn solid red for 2 seconds and then begin to flash.
4. When the LED flashes twice (2), turn the ignition ON. (number 2 was entered)
5. Turn the ignition OFF and wait for the LED to flash once (1) and then turn the ignition ON. (number 1 was entered)
6. Turn the ignition OFF and wait for the LED to flash ten (10) times and then turn the ignition ON. (number 0 was entered)
7. Turn the ignition OFF and wait for the LED to flash six (6) times and then turn the ignition ON. (number 6 was entered)
8. Turn the ignition OFF and wait for the LED to twice (2) and then turn the ignition ON.(number 2 was entered) The LED will turn solid red, which means the system is now overridden and the vehicle can be started. If an incorrect number is entered in, wait 11 flashes then start the procedure again.
NOTE: This is a one-event override. Once the ignition is turned off, the vehicle will passively immobilise after 30 seconds. If your 5 digit override number does not override the system, the chances are that you entered the wrong number. If this is the case, you’ll need to re-enter the override number
and try it again.

Posted on Jul 15, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If I override the alarm and the vehicle still does not start, what then ?, I have checked the battery terminals and they are  fine, with out taking out the battery and replacing it, it seems to have a good charge as the lights stereo and electrical system do not die when you turn the key. would you have any suggestions as to the next step ?

Posted on Jul 28, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 111 Answers

SOURCE: I OWN A 2001 JAGUAR

Hi, usually the problem is the` reader` which is the device which takes the information from the
ignition key and sends it to the ecu.
This reader is situated in the steering columm ( not sure exactly where ).
Have the key checked as the code in the key could be currupted.
Hope i have shed some light on this problem.
John ( South Wales UK )

Posted on May 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a isuzu 2002 trooper and from i replace the battery the engine turn over but it wont start


replacing the battery energises the immobiliser so it will not allow the engine tom start. Try using a scanner to reset the immobiliser

Oct 30, 2014 | 2002 Isuzu Trooper

3 Answers

How can you bypass an antitheft system on a 2002 tdi jetta?


If it is not a new key fob, it sounds to me like the immobilizer is activated. So, all the lights on the dash are working now? Is there a flashing key on the dash lights? One of the resets that works is put the key fob in, and turn ignition on without starting it, and leave it 15 minutes. And try again.

Jul 25, 2014 | 2002 Volkswagen Jetta TDI

1 Answer

Renult megane immobiliser is not turning off and not allowing engine to start


There is a manual override switch inside the car that can turn it off.
Consult the alarm/immobiliser fitment centre for exact details.

Jun 15, 2014 | 1999 Daewoo Lanos

1 Answer

Mercedes key remote


you probably will not start the car as the immobiliser needs the key battery to transmit the code to allow the immobiliser to work correctly. Fit a new battery in the key fob and have it reprogrammed to the engine CPU.

Jan 10, 2014 | Cars & Trucks

1 Answer

My ford sierra does not turn over, immobiliser wont allow it to start


Very common story, your electrical system took a shook and has forgotten its memory, that means it thinks that it is stolen, no shortcuts sorry, it has to go to a dealer, if you ring them they may be able to come to you
Merry Christmas

Dec 14, 2013 | 2001 Volkswagen Golf

1 Answer

Hit pot hole in magna veranda 94 car stopped...now immobiliser will not work and start


I would be checking for a loose battery terminal ( from the bump) or a damaged battery. The immobiliser normally will not allow spark and normally does not stop the cranking action of the engine. If it is an auto a broken isolator switch for the park/ neutral position will also causes the fault

Dec 10, 2013 | 2002 Toyota RAV4

1 Answer

1998 terrano immobiliser fault wont start


hi, i have nissan terrano wen i switched on engine light flash and start engine its start then go of.nissan terrano patrol engine

Sep 06, 2012 | Nissan Sentra Cars & Trucks

1 Answer

I OWN A 2001 JAGUAR S-TYPE V8 AND WHEN THE ENGINE TURNS OVER, THE IMMOBILISER LIGHT STAYS FLASHING AND WILL NOT ALLOW THE CAR TO START. THE AA ADVISED ME THAT THE IMMOBILISER IS NOT TELLING THE ECU TO...


Hi, usually the problem is the` reader` which is the device which takes the information from the
ignition key and sends it to the ecu.
This reader is situated in the steering columm ( not sure exactly where ).
Have the key checked as the code in the key could be currupted.
Hope i have shed some light on this problem.
John ( South Wales UK )

May 04, 2011 | Jaguar S-Type Cars & Trucks

Not finding what you are looking for?
1999 Daewoo Lanos Logo

2,458 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...