Question about 1989 Nissan Pulsar

Open Question

Clutch cable for 89 Nissan pulsar nx

How to replace clutch cable for 89 Nissan Pulsar nx ?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 176 Answers

SOURCE: My friend recently got a nissan 87 pulsar nx, but

Your local auto parts store can get you the repair manual. As far a an owners manual, possibly from the Nissan dealer, or there are some available online.

Posted on Nov 08, 2009

Ad
  • 171 Answers

SOURCE: 1988 Nissan Pulsar will not engage clutch. Engine

You need to replace the clutch and pressure plate --your clutch is worn out. Plus other parts like throw-out bearing ,pilot bearing and may even need the flywheel machined flat.
You need to take it to a shop or if you are mechanicaly minded could do it your yourself,

Posted on Nov 15, 2009

alicantecoli
  • 22156 Answers

SOURCE: instructions on replacement of a Nissan Pulsar N13 transmission?

manual or auto

Posted on Dec 19, 2009

  • 593 Answers

SOURCE: Clutch cable just fixed and just started to stick to floor again

Check each end of the cable, there should be a clamp that holds the cable casing in place. If the
clamp became loose, when you step on the peddle
it would pull the cable and case not the clutch fork.
And the result would be, what you have now.
I hope this was of some help.

Posted on Jan 28, 2010

  • 57 Answers

SOURCE: 83 nissan pulsar NX

Check he mas air flow censor, 02 censor and the throttle position sencer. Assuming you have done all the required maintenance on the vehicle like the air filter, oil, spark plugs, wires, cap and roter.

Posted on Feb 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1988 nissan pulsar n13 keeps getting stuck in first gear


YOUR CLUTCH CABLE MAY NEED ADJUSTING,HERE'S A LINK ON IT,

Feb 12, 2014 | 1988 Nissan Pulsar

1 Answer

1988 nissan pulsar nx idles rough


The Pulsar starter is located centrally, underneath the engine close to the passenger compartment."According to my car, the E16i engine, it is on the drivers side of the engine below/behind the distributor.


Performance chips of BMW.

May 31, 2012 | 1988 Nissan Pulsar

1 Answer

How do you take the stock shift knob off of an 89 nissan pulsar nx


it should unscrew if it dont have align screws on side of knob

Jan 23, 2011 | 1989 Nissan Pulsar

1 Answer

I have a 1987 Nissan Pulsar NX. the problem is, when I try to shift into reverse, it grinds pretty bad. I tried adjusting the clutch rod but it didn't help. Do you have any ideas? Thank you.


I thought these had a hydraulic clutch. Bleed it at the slave cylinder. Its a bleeder screw just like on the brakes. Takes two people

Aug 13, 2010 | 1987 Nissan Pulsar

1 Answer

83 nissan pulsar NX


Check he mas air flow censor, 02 censor and the throttle position sencer. Assuming you have done all the required maintenance on the vehicle like the air filter, oil, spark plugs, wires, cap and roter.

Feb 08, 2010 | 1983 Nissan Pulsar

1 Answer

Clutch cable just fixed and just started to stick to floor again


Check each end of the cable, there should be a clamp that holds the cable casing in place. If the
clamp became loose, when you step on the peddle
it would pull the cable and case not the clutch fork.
And the result would be, what you have now.
I hope this was of some help.

Jan 28, 2010 | 1990 Nissan Pulsar

1 Answer

1988 Nissan Pulsar will not engage clutch. Engine


You need to replace the clutch and pressure plate --your clutch is worn out. Plus other parts like throw-out bearing ,pilot bearing and may even need the flywheel machined flat.
You need to take it to a shop or if you are mechanicaly minded could do it your yourself,

Nov 15, 2009 | 1988 Nissan Pulsar

1 Answer

My friend recently got a nissan 87 pulsar nx, but doesn't have a manual for it... where would a person get one of these?


Your local auto parts store can get you the repair manual. As far a an owners manual, possibly from the Nissan dealer, or there are some available online.

Nov 08, 2009 | 1987 Nissan Pulsar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...