Question about 2005 Lincoln LS

1 Answer

Rear lower break light, how to remove the light assembly to install a new bulb. I can remove the carpet like cover, and pull out the hole cover, but getting to the bulb seems impossible. Does the steel cover come off, or is there a nice neat way to break into it.>?

Posted by on

Ad

1 Answer

You remove three or so nuts and remove the light assy/housing. The steel cover as you put it is your body

Posted on Oct 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change bulb right rear turn signal on a 92 town car


Quoting from link:

https://itstillruns.com/replace-lights-lincoln-town-cars-7660993.html



Tail Lights, Stop Lights and Rear Turn Signal Lights

Turn the Town Car's engine off, and open the trunk. Remove the trunk retainer if your Town Car is equipped with one. Put on the gloves.
Pull the carpet away in order to access the tail lamp assembly. Remove the three nut-and-washer assemblies with a socket wrench.
Remove the desired bulb socket by turning it counterclockwise, and then pulling it straight out of the assembly. Pull the old bulb out of the socket, and install a new bulb. All three lights use 3457AK-type bulbs.
Place the socket back into the assembly, and reinstall the three nut-and-washer assemblies. Place the carpet back into the vehicle, reattach the trunk retainer if necessary, and close the trunk.

https://itstillruns.com/replace-lights-lincoln-town-cars-7660993.html

Apr 23, 2018 | Lincoln Town Car Cars & Trucks

1 Answer

How to change high mount brake light bulb in a 2002 lincoln navigator


Instructions
    • 1 Open one of the rear doorsicon1.png of the LS. Position yourself on your knees in the back seat, facing the rear deck or rear dash.
    • 2 Remove the cover from the high-mount brakeicon1.png light assembly, by hand. Pull the cover toward the front of the vehicle. Do not pull extremely hard, or you will break the clips that mount through the deck from the trunk.
    • 3 Pull the old light bulbsicon1.png out of the high-mount assembly. Wrap the new bulbs in a paper tower prior to picking them up. Insert new bulbs into the assembly, by hand. Do not touch the bulb lenses with your hands directly.
    • 4 Install the high-mount cover onto the rear deck and push the cover toward the rear glass to lock it in place.


Read more: http://www.ehow.com/how_10060583_replace-upper-brake-bulb-2001-lincoln-ls.html#ixzz30cNQ559F

May 03, 2014 | Cars & Trucks

2 Answers

Have no users manual and i'm not sure how you would replace the light bulb on the brake light


Change the Rear Brake Lights
  • Open the trunk and twist the retaining wing nuts off the studs holding the carpeted trim cover in place on the back side of the tail lamps.
  • Pull the carpeted trim cover out of the way and pry the plastic caps out of the holes with the screwdriver tip.
  • Unbolt the nuts holding the tail-lamp assembly in place using the socket set.
  • Pull the tail lamp assembly away from the body of the Stratus. Grab the socket for the bulb in question and twist it counterclockwise to remove it. Pull the old bulb out by hand and insert the replacement bulb. Reinstall the socket in reverse of removal.
  • Push the tail lamp assembly back into position and tighten the nuts back down onto the retaining studs using the socket set. Pop the plastic caps back into the holes, pull the carpeted trim cover back into position and reinstall the plastic wing nuts. Close the trunk.

Jul 21, 2011 | 2006 Dodge Stratus

1 Answer

Need to change out a broken tail light cover for a 2002 mercury sable


Replacing tail/brake/turn signal/backup lamp bulbs (page 59-60 of owners manual)

Sedan

The tail lamp, brake lamp, turn

signal lamp and backup lamp bulbs

are located in the same portion of

the tail lamp assembly. Follow the

same steps to replace either bulb.

1. Make sure headlamp switch is in

OFF position and open trunk and

remove two plastic mushroom nuts,

three push pins and the plastic

cover from inside the trunk to

access the lamp assembly.

2. Carefully pull the carpet away to

expose the lamp assembly hardware.

3. Remove four nut and washer

assemblies and the lamp assembly

from the vehicle.

4. Remove the bulb socket by

rotating it counterclockwise, then

pulling it out of the lamp assembly.

5. Pull the bulb from the socket and
push in the new bulb.

6. Install the bulb socket into the lamp assembly by rotating it clockwise.

7. Install the lamp assembly on the vehicle with four nut and washer

assemblies ensuring the washers on the nuts are flush with the body to

prevent water from entering the trunk.

8. Carefully push the carpet back in to place and install the plastic cover
inside the trunk with three push pins and two plastic mushroom nuts.

May 31, 2011 | Mercury Sable Cars & Trucks

1 Answer

How do I get to the back up light on a 1988 Delta 88?


  1. Most rear lamps can be accessed from inside the trunk. Open trunk and look for access past the carpet.
  2. By pulling back the carpet or removing the large plastic carpet retaining nuts, you can see the back of the light assembly.
  3. If you can reach the bulb from inside the trunk, you don't need to remove the lens assembly to replace the bulbs. But, if you can't reach the bulb and connector assembly, you may need to remove the lens assembly.
  4. If necessary, remove the tail light panel screws and the lens assembly.
  5. You can now simply turn the bulb connector assembly counterclockwise and remove it from the lens housing.
Fig. 8: Once the carpet is pulled down, you can see the retaining wingnuts which must be removed to access the rear bulbs


tecnovative_48.jpg
Fig. 9: Carefully pull the rear light assembly away from the vehicle for access to the bulbs


tecnovative_49.jpg
Fig. 10: Depress the bulb and socket retaining tabs, turn the socket . . .


tecnovative_50.jpg
Fig. 11: . . . then pull the bulb and socket from the rear of the lens


tecnovative_51.jpg
Fig. 12: Carefully press the bulb in and twist it approximately 1⁄8 turn counterclockwise to remove it from the socket


tecnovative_52.jpg

Jan 31, 2011 | 1988 Oldsmobile Delta 88

3 Answers

Tail lights do not work on a 2000 lexus rx 300 bulbs are fine, all other lights work fine


You may have a fried fuse. Look in your owners manual to find out which fuse it is in the fuse box diagram. If that is the problem make sure to use the same amperage fuse to replace the burned one with. I fried fuse is usually a sign that you have a short somewhere. But they can also fry for other reasons such as excess moisture somewhere. Sometimes they just burn from age and fatigue. It may solve it to just replace the fuse, but if there really is a short, the new fuse will fry too.

Dec 29, 2010 | 2000 Lexus RX 300

1 Answer

How do I replace the heating fan on my 2000 Kia sportage


Blower Motor
Removal & Installation
To Remove:


  1. Evacuate and recover air conditioning refrigerant.
  2. Remove battery.
  3. Disconnect and cap A/C lines at evaporator tubes.
  4. Remove blower motor assembly drain.
  5. Remove glove box.
  6. Remove 5 screws and right hand instrument panel lower trim panel.
  7. Remove screw that attaches upper center console to gain access to left
    instrument panel lower support.
  8. Remove left and right bolt and remove instrument panel lower support.
  9. Detach control cable from inlet duct.
  10. Disconnect blower motor electrical connector.
  11. Pull carpet back and remove hole cover plate.
  12. Remove 2 bolts at top of blower motor assembly.
  13. Remove 2 nuts that attach bottom of blower motor assembly to mounting studs
    on bulkhead.
  14. Remove blower motor assembly.

To Install:


  1. Install blower motor assembly.
  2. Install 2 bolts at top of blower motor assembly.
  3. Install 2 nuts that attach bottom of blower motor assembly to mounting studs
    on bulkhead.
  4. Install hole cover plate and replace carpet.
  5. Connect blower motor electrical connector.
  6. Install instrument panel lower support and install left and right bolts.
  7. Install right hand instrument panel lower trim panel and 5 screws.
  8. Install glove box.
  9. Install blower motor assembly drain hose.
  10. Connect evaporator lines at bulkhead.
  11. Evacuate and charge air conditioning refrigerant.
  12. Install battery.

Oct 29, 2010 | 2000 Kia Sportage

3 Answers

Access for replacing brake light bulbs: Is it from the trunk or under the rear bumper?


you can access the bulbs from the trunk, remove the covering from the inner back of the rear.

Feb 18, 2010 | 1988 Buick LeSabre

2 Answers

Replace rear window brake light bulb


I just had to do this, and it isn't all that easy or quick. First, gently work the gray, carpet like cover loose from the area around the tail light ,(this may give you a little trouble). Once you have done this, you will see three silver nuts. These must be unscrewed. The lower left nut must be accessed through a hole next to where the trunk lid fits. (The screws are permanently attached to the lens housing so will not drop into obscurity when the nuts are removed). After removing the nuts, GENTLY work the lens housing away from the car. You may need a screw driver to unseat the housing, but just be gentle.

You will find three bulbs inside the lens. The brake light bulb is on the lower right side. Simply pull the old bulb out and insert the new one.

Just reverse these directions to reassemble the housing.

May 04, 2009 | 2002 Lincoln LS

1 Answer

How do I replace a taillight lens on a 1991 Geo Storm?


Rear Turn Signal, Brake and Parking Lights


STORM COUPE
  1. Disconnect the negative battery cable.
  2. Lift the luggage compartment floor carpet toward the front of the vehicle and remove the spare tire cover panel.
  3. Remove the ten plastic retaining clips from the rear end trim panel.
  4. Disconnect the luggage compartment lamp electrical connector.
  5. Remove the luggage compartment trim panel and the rear end trim panel.
  6. Disconnect the rear combination lamp assembly electrical connector. Fig. 1: Rear Turn Signal, Brake and Parking Lights — Storm
84256028.gif
  1. Remove the seven nuts and the rear combination lamp assembly from the vehicle.
  2. Disconnect the rear combination lamp electrical connector.
  3. Remove the four bulb sockets from the rear combination lamp assembly and remove the four bulbs from the sockets. To install:
  4. Install the four bulbs to the sockets and install the four bulb sockets to the rear combination lamp assembly.
  5. Connect the rear combination lamp electrical connector.
  6. Install the rear combination lamp assembly to the vehicle and the seven nuts.
  7. Connect the rear combination lamp assembly electrical connector.
  8. Install the rear end trim panel and the luggage compartment trim panel.
  9. Connect the luggage compartment lamp electrical connector.
  10. Install the ten plastic retaining clips to the rear end trim panel.
  11. Install the spare tire cover panel and the luggage compartment floor carpet.
  12. Connect the negative battery cable.

Mar 21, 2009 | 1991 Geo Storm

Not finding what you are looking for?
2005 Lincoln LS Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

fordexpert

Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...