Question about 1990 Peugeot 405

1 Answer

Which way does fan belt go on pullys - 1990 Peugeot 405

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 580 Answers

Writing side out.

Posted on Jul 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reroute the drivibg belt or fan belt


Hi,just inline the crankshaft to the top dead centre marks,then check that the camshaft marks line up,if they dont line up then turn the crankshaft pully again untill the camshaft marks line up,slacken the timeing belt pully adjuster take belt off and replace with new one,tighten the pully adjuster back up,now put a spanner on the crakshaft pully and turn clockwise untill the top dead centre marks and the camshaft marks inline if they dont then slacken the ajusting pully inline marks again and try again,if marks do inline ok then you are ready to start the car.
hope this helps good luck.

Feb 25, 2015 | Cars & Trucks

Tip

How to replace a fan belt without a diagram


if your trying to repalce a fan belt without a diagram you can use 2 very simple things to make your self a diagram and its ok if you dont know what all the pulley go to or what they do. take a peace of paper and a pen or pencil and starting with the pullies draw a few differet circles i would start with the bottom pully cause its the crankshaft pullie make your circle and then move on to the next pullies now when your done with that draw the way that the belt goes i will latter on try to add a example of what im talking about.

on Dec 05, 2010 | Chevrolet Chevy Cars & Trucks

1 Answer

I cant get the old radiator fan off cuz the pully spins


Try tightining the fan belt. if that doesnt work try to jam a screw driver behind the pully without ruining it while looseing the pully. remember bolts comming off turn counter clockwise.

Nov 20, 2010 | 1998 Chevrolet Blazer

1 Answer

Want to fit fan belt cant find the proper way


You have to find the tension pully. using a 3/8 socket wrench. not the socke but the actual wrench. place the square end of the wrench into the notch on the pully and either push or pull (depends on the v-belt system) and it should move. place your v-belt around the pully's according to the diagram under your hood leaving your tension pully to be the last one the belt goes on. Move that tension pully as mentioned above and place it the belt on the pully. The diagram under the hood should also show you where that tension pully is located.

Oct 04, 2010 | Ford Fusion Cars & Trucks

1 Answer

How to instal fan belt on 85 cadilac eldorado


You need to locate the tension pulley and by moving it with a wrench you will have enough slack to finish the job BE CAREFUL it can require a lot of power to release the tension

Mar 10, 2010 | 1985 Cadillac Eldorado

2 Answers

My serpintine fan belt came off as I started the motor; w/o air conditioner, but it does have power steering- the new belt seems to be too long, even though I had brought in the old one and followed the...


All it takes is for one part of the belt to be in the wrong position for it to appear to be too long. Check the diagram again. There is often a diagram in the owner manual as well as under the hood.

Oct 15, 2009 | 1989 Chevrolet G20

1 Answer

How to tighten my 306 dt 98 fan belt


you need to take off the drivers front wheel and plastic cover infront of the engine.
then you need to crack off two allen key type bolts holding the braket and tensioner pully in place, that is positioned just right of the crankshaft pully. Once the whole unit is slack you have to loosen the adjuster that is visible underneath the tensioner braket to take the tension off the belt. Once the belt is loose enough take it off and reverse process avoiding overtightening new belt. [It needs a little give to avoid damging bearings in the pully]

Sep 01, 2009 | 1990 Peugeot 405

2 Answers

How do i change the fan belt


well has soon as you loosen and take out the alt the belt will become loose then put alt on it will slide down to put belt around and then pull up on alt and tighten it up

Jan 25, 2009 | 1988 Mazda B2200

1 Answer

REMOVAL OF THE SERPENTINE BELT AND THE FAN BELT


you should look for spring loaded tension pully .in this pully you will find a square hole put a 1/2 inch drive ratchet (no socket) into this hole & apply pressure until belt loosens don't forget remeber the way belt came off

Jan 06, 2009 | 1995 Nissan Maxima

Not finding what you are looking for?
1990 Peugeot 405 Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...