Question about 1995 Pontiac Grand Am

1 Answer

New ignition wont fire at all

I just bought a new ignition for it and installed it and now the power comes on in the car, but the ignition does not fire at all. what is wrong?is it something with the computer? please help.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

Gm has an old factory theft deturant system, disconnect the battery for at least five minutes and reconnect should reset the system to enable you to start it. If it will still not continue ensure the ignition is the right one and everything is installed correctly and in the right sequence order

Posted on Jul 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wont hit a lick is firing fuel system wont run unless u hot wire and the spot for relay is dead and has new engine brain still nothing.


Try changing the electronics on your ignition switch. All of the power to the rest of your car goes through your ignition switch and if the switch is bad the car won't start because power is not getting to where it needs to be. I am almost positive that if you replace the ignition switch electronic your car will run fine. I hope this helps

Aug 26, 2011 | 2002 Kia Sportage

1 Answer

The dash gauges all work , fuel pumps are both good , the fuel pumps wont come on and the truck trys to fire when i turn the ignition on but wont , could this be a fuel regulator


did you check the fuel pressure pump on the frame rail for power and ground? have you verified no ignition spark to the spark plugs? have you checked for fire from the coil to the distributor cap? does the check engine light come on when you turn the key on? have you check for injector pulse and power at the fuel injectors? if the fuel pump won't come on and you have no ignition fire and no injector pulse, all of these systems are triggered by the ECM.

Aug 12, 2011 | 1990 Ford F150

1 Answer

1995 s-10 blazer 4.3 vortec wont start. have 57 psi at intake. wont fire with eather, new gm spider. advance auto fuel pump. filter.


well if the spyder is installed correctly, and will hold at least 45PSI, then it sounds like an ignition problem, make sure it has fire at all cyl's. I would check and make sure all injectors have a good pulse signal, and double check the ignition system.

Jan 28, 2011 | 1996 Chevrolet Blazer

1 Answer

Key does not come out, car wont start


The key is bounded up in the ignition cylinder from a bent lock tumbler
A new replacement ignition cylinder is the only remedy that will fix this problem

May 29, 2010 | 2004 Cadillac SRX

1 Answer

I have a 1992 dodge stealth base and i hooked up a chip to the mass air flow sensor but i didnt wrap the wires up after installing the chip the car shut off when i shut my hood and grounded the wires out.....


You may have actually damaged the MAF sensor itself. Inside the mass airflow sensor are a couple of very delicate resistors which can almost immediately be ruined if the wires get shorted to ground while the ignition key is turned on.

Feb 25, 2010 | 1991 Dodge Stealth

2 Answers

Daewoo lanos 2000 car is misfiring and wont run properly firing on cylinders 1 and 4 misfiring


have you changed the ignition wires? perhaps firing order crossed? if not coil pack or ignition wires faulty how do you know it is not "FIREING" on 1 & 4 have you tested it with a spark tester tool???

Dec 23, 2008 | 2000 Daewoo Lanos

Not finding what you are looking for?
1995 Pontiac Grand Am Logo

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...