Question about 1990 Nissan Pulsar

1 Answer

97 pulsar eratic tacho operation - 1990 Nissan Pulsar

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 580 Answers

Replace your tachometer cable it is stretched, twisted, or snapped.

Posted on Jul 13, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a desiel pilote the rev counter does not work it is built on a boxer chasis

if you have a cable operated tacho or there is a cable to an electronic box that provides the pulse for the tacho the check that the cable is operational and is in the drive gear.

Aug 12, 2014 | Cars & Trucks

1 Answer

Tacho on 95 pulsar

Replace the hall effect sensor in the transmission.

Apr 15, 2014 | Nissan Pulsar Cars & Trucks

1 Answer

Eratic tachometer, then the car suddenly stops running

The tacho is fed from the ignition system, so you should expect a problem with either connections to the ECU or a failed ECU.

Mar 24, 2013 | 1997 Honda Civic

1 Answer

My 97 monte wont start on its own. very hard start, we have changed the oxygen senser, egr, plugs wires dont know what to do any ideas

OK so the problem is the timing chain and gear set. factory timing gears are nylon coated, so wear out in time. the eratic idle indicates wandering timing, controlled by timing gear set. suggest new ones that do not have nylon gears.

Mar 17, 2013 | Chevrolet Cars & Trucks

1 Answer

1999 Nissan pulsar tacho jumps even when just on accessories. Need help!!!! I've uploaded a video of it . Any help much appreciated

Couple things could happen
You might have some wiring that might be frayed or the sensor inside the distributor might be bad that's what reads the tach it's called an optical sensor you need to replace the whole distributor most Likly that's your problem

Nov 30, 2012 | Cars & Trucks

1 Answer

How to use Vag Tacho 3.01+ Opel Immo Airbag scanner

Read the operating and use instructions, we do not have them.

Apr 20, 2012 | Cars & Trucks

3 Answers

Dashboard instrument cluster faulty - fuel gage, odometer, tacho and trip counter not working on my nisan n13. Fuel gage shows pessimistic eatimat of fuel in tank. Odometer stopped one year ago when the...

N13's are terrible for this problem, the odometer stops because of a faulty little nylon cog that has to be replaced, the tacho and gauges in n13 dashed die as well but as far as I know that's because of faulty electronics, if it was just the odometer problem you couldv'e bought the cog off ebay (and with a little mechanical knowledge) you could've taken the dash apart and re installed it yourself but because the other electronics are dying I advise you take it to a dash repairer or you can try getting out a soldeing iron and try to replace all the faulty connections yourself.

Feb 20, 2010 | 1990 Nissan Pulsar

1 Answer

My 89 pulsar speedo amd tacho imtermittently work.

remove the cluster and check the connections in the back for speedo, try unpluging and reconnecting if not replace the cluster.

Jan 11, 2010 | 1989 Nissan Pulsar

1 Answer

Nissan Cube, Cannot Find Coil Negative has free online repair manual and is free to register Just follow the plug wire. What plug wire did you have it on? Should have it on #1 cylinder wire.

Apr 15, 2009 | 1990 Nissan Pulsar

1 Answer


its the red and white wire behind the guages

Mar 19, 2009 | 1989 Nissan Pulsar

Not finding what you are looking for?

Open Questions:

See all 1990 Nissan Pulsar Questions

1990 Nissan Pulsar Logo

Related Topics:

270 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides