Question about 1995 Lincoln Town Car

1 Answer

How to remove p/s pulley on 1991 lincoln town car 4.6

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 106 Answers

You will need to remove the power steering pump from the car as the pulley is pressed on.
You will either need to take it to a mechanic or purchase the tools to do it yourself.

Posted on Aug 03, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to remove power steering pump.

You have to use a socket(1/2 inch or 13 mm) threw the pulley to remove the pump. But I think you have to drop the alternator out the bottom. Remove the frame bolts. Good luck.

Jul 12, 2015 | 1991 Lincoln Town Car

1 Answer

A/c clutch replacement on 2004 Lincoln Town Car

pull the belt, should be three bolts on the pulley itself. once extracted pulley puller to remove hammer new one on with dead blow or rubber mallet assuming you get complete pulley set already assembled with clutches (highly recommended) replace belt

May 18, 2012 | 2004 Lincoln Town Car

1 Answer

My 1991 Lincoln town car sat for awhile. Now when driving smell a burning electrical smell and when braking it pulls to the left. Any idea what the problem is?

You have a lot of rust on all your brake components

You will need to completely strip all 4 brakes & remove
all rust and lube necessary parts

Don't misunderstand my point here

You do not necessarily need new rotors or brake pads

You may want to however, replace the flexible rubber
brake hoses, as they may have collapsed inside and
your brakes do not release,thus the brake pad smell

Also you could have rusted and frozen caliper pistons

The rust,the flex hoses & possibly the calipers, are your
problems,and the cause of the bakes not releasing

Mar 06, 2011 | 1991 Lincoln Town Car

2 Answers

Fan clutch removal 1991 town car w/ 4.6L?

using a fan clutch removal tool

undo all of the bolts holding the fan clutch in and remove, very simple task, but using a special tool can expedite the process

Mar 01, 2011 | 1991 Lincoln Town Car

2 Answers

How do I install a serpentine belt on my 1991 Lincoln Town Car?

Welcome to



Regards, Lee Davidian

A Four Thumbs up ^^^^ is appreciated for answering your question. And please take the time to rate me by leaving a testimony. Thank you, Lee Davidian

Oct 17, 2010 | 1991 Lincoln Town Car

1 Answer

Need spark plug calbration for 1991 lincoln town car and firing order

For 1991 Lincoln Town Car 4.6 liter SOHC V-8 VIN "W" check Firing Order...


Year: 1991
Engine: V8 - 4.6L - FI - - GAS
Spark Plug Champion:
Part Number RS14YC6 OE GAP .054" (Original Equipment Manufacturer and/or Original Equipment Equivalent)

Hope help with this (remember rated this post) Good luck.

Feb 22, 2010 | 1991 Lincoln Town Car

1 Answer

How Can I remove the sterring pump from a Lincoln 1990 Town Car?

You are going to need a special tool to remove and install the pulley, you can maybe rent one from you local auto parts store. Once the pulley is off just remove the bolts and disconnect the hoses. The inside of the pump shaft is threaded for the installation tool, make sure you get the tool fully seated before you attempt to install the pulley. The hub of the pulley should be flush with end of the shaft when you are done.

Dec 20, 2009 | 1990 Lincoln Town Car

1 Answer

What is the plasic pully on a 1991 lincoln town car engine?

is it just a pulley on its own not attached to any gear apart from its bracket? if so that there is your belt tension pulley its how you remove or tighten the belt by ajusting the screw at the back and moving it

Oct 29, 2009 | 1991 Lincoln Town Car

1 Answer

Where is the air compressor located in a 1991 Lincoln Town Car?


The compressor is located in a compartment in the left front wheel hub. To access it you have to remove the air cleaner and the washer fluid reservior.


Jun 28, 2009 | 1991 Lincoln Town Car

1 Answer

I need to change the power stearing seal in my 1993 ford lincoln.

if the power steering pump to bracket bolts are behind the pulley you will need a special puller to remove the pulley and once the pulley has been remove there are three mounting bolts you be able to see if you have a autozone need you there you can rent the special puller you need and then take it back and get you money back also try this website to see if they have your car listed it if they do you be able to get pictures and diagrams showing you how to repair it as well i also have a 93 Lincoln Town Car i hope i have been some help to you Michigan Man

May 05, 2009 | 1993 Lincoln Town Car

Not finding what you are looking for?
1995 Lincoln Town Car Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts


Level 3 Expert

79024 Answers


Level 3 Expert

5676 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides