Can automatic transmission with no reverse, 2nd or 4th gear be fixed without rebuild?

If it grinds when trying to shift, it is the synchronizers. Rebuild. If it pops out of gear. there is a plastic part at the top of the transmission that wears out. It fits around the ball of the shifter. It is two pieces. You'll have to remove the floor plate and pull it up to access the bolts to remove the shifter and replace those plastic pieces.

Pull the transaxle & rebuild it or install a reman

Can't fix slipping

For Automatic transmission problem,Check the list of help links below.click the link below:----Automatic transmission troubleshooting:----

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html

---------
Automatic transmission shift lever issues?-------

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

-----------
AUTOMATIC TRANSMISSION FLUID LEVEL? --

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

--------------

AUTOMATIC TRANSMISSION FLUID AND FILTER?

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

-----------
Transmission fault light on car dash?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html

--------
Transmission shifting problem?

http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html

--------
Transmission Slips out of 2nd gear?

http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html

-----------
OD light flashing and transmission fluid leaking?

http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html

----------
Why Transmission fluid leaks near radiator?

http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html

----------
transmission fluid leaking?

http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html

-------------
****** wont go in reverse?

http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html

-------------
Automatic transmission will not go into reverse?

http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html

----------
Transmission is making buzzing noise?

http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html

-----------

This will help.

Thanks.

possible stripped 2nd gear syncromesh. Used or rebuild transmission required

This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Trans shifts into gear harshly, car feels sluggish off the line, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Hi:

Your transmission has 3 shift rails...
1st - 2nd
3rd -4th
5th- Reverse

If your 3rd gear doesn't work , you have an internal transmission problem, such as a syncronizer, or similar fail... There is not much you can fix, without removeing the transmission.

• No 3rd or 4th gear: “3-4” clutches are worn out. R&R. The car is safe to drive (in 2) until you can get it fixed.
• Trans shifts into gear harshly, car feels sluggish off the line, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.
• No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : Shift A solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Check to see if your transmission is in the limp mode, which would only give you 2nd, 3rd and reverse gears. No 1st or 4th gear.

I had the same problem but eventually lost reverse. Had to get a new transmission... $2,300.00

im not telling you what to do because it could be a bad transmission and an easy fix but I cant tell without looking at it , but if its a hard fix just go to a reliable junkyard and get another

Is it missing reverse 2nd and 4th? If so it has a broken reverse reaction shell. They aren't too hard to replace