Question about 1998 Honda Prelude

1 Answer

Yes on cover - 1998 Honda Prelude

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 175 Answers

Yes on cover...... What does that mean? I think you need to be a little more descriptive than that.

Posted on Jul 13, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Is there a way to check the timing belt placement without removing the timing belt cover?

Make,model and year and engine? Yes,some have an inspection hole,and others you just need to remove the top cover or the bottom cover. don-ohio

Jan 04, 2017 | Cars & Trucks

1 Answer

Is there a fuse for this car, if so, where is it located, also, there is a clear plastic cover covering the ignition fuse, how is it removed?

Yes, there are fuses for all cars, ignition fuse cover has clips either side that need depressing and pull the cover at the same time.

Oct 08, 2015 | Cars & Trucks

1 Answer

My windshield wipers on my 2000 Pontiac Montana won't stop as soon as I turn it on they start going I have tried turning it off of course but they just keep going

The switch is bad or the wiper motor cover ,electronics !
  1. Turn the ignition switch to RUN.
  2. Turn the wiper switch to OFF.
  3. Disconnect the wiper/washer switch connector C201.
Do the wipers park? yes or no ?
if yes Replace the wiper/washer switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle .
if no
Measure the voltage from connector C201 (vehicle side), terminal E2, to ground with a DMM.
Does the voltage measure greater than the specified value?
1.0 V yes or no ?
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
Did you complete the replacement?
Go to Step 9


  1. Reconnect the wiper/washer switch connector C201.
  2. Disconnect the wiper motor connector.
  3. Measure the voltage from the wiper motor connector, terminal D, to ground with a digital voltmeter.
Does the voltage measure greater than the specified value?
1.0 V
Go to Step 8
Go to Step 7


Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
Did you complete the replacement?
Go to Step 9


Repair the short to voltage in CKT 113. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 9


Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Wiper/Washer System Check

if yes

Apr 20, 2015 | 2000 Pontiac Montana

1 Answer

Can a turbo make the engine use oil and smoke.

Yes a turbo with faulty oil seal can and will use oil and smoke, and yes the valve stems will have rubber covers but usually only blows smoke each time you start the engine, but will then disapate after running or normal driving

Sep 09, 2014 | 2004 Chrysler PT Cruiser

1 Answer

Air blend door actuator

ask a question, the above is a statement.
My blend door is stuck open or closed, or? can i fix it, (yes) can i get it fixed (yes,) can i buy the parts (yes) who sells them(acura) and how would i proves its bad, not guess, (yes, we can)
see, ask a real question.
The FSM covers this 100% and some help at
they cover HVAC. the FSM even does the step by stem thing...

Oct 15, 2013 | 2003 Acura 3.2TL

2 Answers

Do I need to remove pulley to change timing change cover gasket?

If you mean the crank shaft pulley then yes you have to remove to remove the timing cover.Hop[e this helps.Good luck.

Mar 04, 2011 | GMC Savana Cars & Trucks

2 Answers

I pulled a spark plug to change plugs and the spark plug wire boot was all wet from oil. The other three plugs were fine. The rest of the engine looked fine apart from the regular dirty engine look. No oil...

yes, the valve cover gasket is the only thing that can cause this, and yes, you have to remove the cover and put a new gasket in to fix. Please let me know if you have more questions.

Sep 09, 2010 | 1996 Saturn SL

2 Answers

2001 jaguar S type v 6. I need to replace the valve cover gasket. Does any one have the torque sequence and torque values for the bolts?

Felpro brand gaskets are the best in the world, not sure about the intake, if it is in the way then yes remove it.

Sep 29, 2009 | 2002 Jaguar S-Type

1 Answer

I bought replacement wire wheel cover for a

yes there should be a code in glove box for locks & key get it go back to dealer get one new lock

Aug 25, 2009 | 1992 Buick Roadmaster

Not finding what you are looking for?
1998 Honda Prelude Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides