Question about 1993 Mercury Grand Marquis

1 Answer

How do you remove door panel?

How do you remove the rear door panel to push the window up?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

First remove the screws from the panel the only one thats hard to find is the one in the cubby once you remove these take a flat head and pop lose i losing the top and just pulled mine off it will still be attached so you have to undo the window/lock harness and then the light at the bottom and also the trunk release and gas tank release soon as you take these off you should be good to go

Posted on Sep 26, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 295 Answers

SOURCE: how remove the rear inside door panel on a 2001 oldmobile aurora

The inner door panel is held in by clips and screw.
Look at the door near the door handle there should be screws holding it in and along the outer edge of the door. Once loose, and the door handle removed or the arm rest removed. The door panel then prys out , because of the clips that hold it on. Then pops out by applying pressure to the panel upward to the top of the door. The clips always break because of the design and plastic.

Good luck

Posted on Mar 21, 2009

p_murfy
  • 63 Answers

SOURCE: window dropped into rear door panel. How do I remove the panel & repair

the window regulator has failed. the door panel has to be removed first which requires removing the trim piece that is on the grab handle (extremely hard to remove without breaking) there are three of four screws that hold the door panel on. once the door panel is off, the vapor barrier has to be removed. don't tear it, it is there for a reason to keep water out of the vehicle. make sure you reseal it properly with window weld. once the vapor barrier is removed you will need to unclip the window glass from the regulator. i typically will take and break the tab that holds the window. once the window is loose, move the glass all the way to the top of the door. now remove the regulator, swap the motor over, and reassembly. i would recommend taking the vehicle to a bmw dealership, around $650 for the complete repair and the dealership will stand behind their repairs

Posted on May 03, 2009

  • 1986 Answers

SOURCE: rear door panel removal

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1986 Answers

SOURCE: How to remove rear door panel on 2001 continental?

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1986 Answers

SOURCE: Remove right rear door panel 2003 Buick LaSabre

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove 2010 Honda cicic rear door panel


You'll need a special cheap metal tool from the auto parts store made of thin metal to push the spring clip from the window crank and door handle, then use it to get behind the door panel at the edges and pop the pins that are attached to the panel out of the holes they go into in the door itself.

Sep 23, 2014 | Cars & Trucks

1 Answer

How to replace town and country door handle


Hi,

Follow instruction below:

Raise the window up completely. Remove the screws from the armrest using a screwdriver. Lift the window switch out of the door panel by prying up rear of the switch and the pulling the switch to the rear, dislodging it in the front. Lift it up and unplug the electrical connectors.

Insert the flathead screwdriver between the door panel and the door and pry out all the trim fasteners from the door on both sides and the bottom. Remove the panel. Peel the moisture barrier back exposing the rear of the door.

Push the door latch actuator rod retainer off the rod, releasing it from the door handle. Remove the two 10 mm nuts securing the outside door handle to the door. Pull the door handle out of the door.

Install the new door handle by holding it in place and installing and tightening the inside nuts. Insert the door latch rod into the door handle lever. Swing the retainer down and push its lock over the rod.

Place the moisture barrier back into place. Install the door panel and push all the trim fasteners into the holes in the door. Install the two screws into the armrest and tighten. Install the window switch by plugging in the electrical connectors. Push the window switch into the hole in the door panel and press the rear of the switch down to lock it in place.

Best regards.

Oct 29, 2010 | 2000 Chrysler Town & Country

1 Answer

How do you remove the inside door panel backseat right side of a mercury grand marque 1996


Door Panels REMOVAL & INSTALLATION 1989–91 Vehicles
  1. Disconnect the negative battery cable.
  2. On 1990–91 vehicles, remove the speaker grille.
  3. Remove the retaining screws from the door inside handle cup.
  4. If equipped with armrest courtesy lamps, remove the lens, detach the bulb and wiring assembly from the pull cup and remove the pull cup.
  5. Working through the pull cup opening, disconnect the remote lock rod from the lock knob.
  6. Remove the retaining screw and the remote mirror bezel nut from the power window regulator housing switch plate, if equipped.
  7. Raise the plate to expose the window switch and power door lock switch and disconnect the switches.
  8. Remove the retaining screws from the armrest finish panel.
  9. Remove the retaining screws from the armrest and remove the armrest.
  10. Using a suitable trim pad removal tool, carefully pry the trim panel plastic push pin retainers from the door inner panel. NOTE: Do not use the trim panel to pry the clips from the door inner panel. Replace any bent, damaged or missing push pins.
  11. Disconnect the radio speaker wiring, if equipped.
  12. Remove the trim panel and watershield. To install:
  13. If the door panel is to be replaced, transfer the plastic push pins to the new panel. Make sure that the watershield is positioned correctly to the door sheet metal. Remove the door pull handle from the old panel and transfer to the new one.
  14. Position the door panel loosely to the door belt opening and route the wiring harness through the appropriate access holes in the panel.
  15. Connect the radio speaker, if equipped.
  16. Align the plastic push pins on the door panel to the holes in the door sheet metal and press the pins into place.
  17. Install the armrest and route the window regulator, remote mirror cable and power lock harness through the access hole.
  18. Install the armrest finish panel.
  19. Install the power window regulator switch plate housing to the armrest connecting the power window switch, power door lock switch and remote mirror bezel nut, if equipped, prior to securing the retainer screw.
  20. Connect the lock remote rod to the lock knob retainer boss. NOTE: Make sure that the remote rod is fully seated into the retainer boss, then function manually or with the power switch to ensure smooth operation of the lock knob.
  21. Install the bulb and wiring assembly.
  22. Install the lamp lens, if equipped, and the pull cup.
  23. On 1990–91 vehicles, install the speaker grille.
  24. Connect the negative battery cable. Fig. 1: Front door panel — 1990–91 vehicles 84170064.gif
    Fig. 2: Rear door panel — 1989–91 vehicles 84170065.gif
1992–98 Vehicles
  1. Disconnect the negative battery cable.
  2. If removing the driver's door panel, remove the nut from the outside rearview mirror control switch.
  3. Remove the window regulator switch housing by gently prying up, starting at the front. Fig. 3: Front door panel — 1992–98 vehicles 84170066.gif
    Fig. 4: Rear door panel — 1992–98 vehicles 84170067.gif
    Fig. 5: Remove the window regulator switch housing by gently prying up, starting at the front 89600p08.jpg

  4. Detach all connectors from the switch housing.
  5. Remove the door inside handle cup.
  6. Remove the push pin from the door trim panel upper front extension and remove the screw.
  7. Remove the lower self-tapping screw retaining the door trim panel to the door inner panel. Fig. 6: Detach the switch housing electrical connector and remove the housing 89600p09.jpg
    Fig. 7: Remove the door inside handle cup 89600p01.jpg
    Fig. 8: Remove the screws from the door panel in the front and on the upper extension 89600p02.jpg

  8. On Grand Marquis, pry up the screw covers from the door pull handle and remove the screws and handle.
  9. Lift the door panel upward and snap out the panel. Fig. 9: There are also retaining screws located in the map pocket as well as . . . 89600p03.jpg
    Fig. 10: . . . along the bottom edge of the door panel 89600p04.jpg

  10. Disconnect the necessary wire harnesses and remove the panel. To install:
  11. Connect the wire harnesses to the door panel, as necessary.
  12. Install the door panel by pushing in and down until it snaps into place.
  13. Install all self-tapping screws retaining the door trim panel to the door inner panel.
  14. On Grand Marquis, install the door pull handle, tighten the screws and install the screw covers.
  15. Install the push pin covering screw on the panel upper front extension.
  16. Install the inside door handle cup.
  17. Install the window regulator switch housing and install the nut on the outside rearview mirror control switch, if removed.
  18. Connect the negative battery cable. Fig. 11: Lift the door panel upward and snap out the panel to remove it from the door 89600p05.jpg
    Fig. 12: Rotate the door marker lamp bulb and remove it from the door panel 89600p06.jpg
    Fig. 13: Detach the connectors for the trunklid and fuel door release switches 89600p11.jpg
    Fig. 14: Slide the relay connector off of the door panel and remove the door panel from the vehicle 89600p17.jpg
prev.gif next.gif

Aug 26, 2010 | Mercury Grand Marquis Cars & Trucks

1 Answer

How do I remove rear door panels


Take the screw out of the inside door ahdnle trim bezle . the bezle will pull out. the there is a cover behind the door pull handle pop that cover off and remove 2 screws . remove the power window switch if equipped or the window crank handle.The door panel isheld in place with push retainers use a door trim panel tool to remove push retainers from the door and lift the trim panel up off top edge of the door

Feb 20, 2010 | 2004 Chevrolet Malibu

1 Answer

How do i replace left door mirior


remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation
  1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
  1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
  1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
  1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
  1. To install reverse Removal procedure.
------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove front door trim panel (23942). Refer to Section 01-05 .
Trim Panels, Door Front—Town Car
Removal
  1. Snap out two door pull strap retaining screw covers. Remove screws.
  1. Remove three screws on front and rear side and center of front door trim panel (23942).
  1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

    Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
  1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

    Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
  1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
  1. Remove the door trim panel.
  1. Disconnect two electrical connectors.
  1. Remove nut from outside rear view mirror mounting base.
  1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
  1. Remove screw from outside rear view mirror base.
  1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
  1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-

Nov 05, 2009 | 1996 Lincoln Town Car

2 Answers

Where can I read, for free, how to remove the drivers door panel and remove and replace the window regulator. I see these questions on this site but there are NO ANSWERS. What's with that? 1998 Cadillac...


GM Cadillac Deville_Fleetwood_ELD_Seville 1990-1998

Door Panels - REMOVAL & INSTALLATION

FRONT DOOR

7b8295a.jpg

Fig. Front door panel-1990-91 Deville and Fleetwood

f86aba7.jpg

Fig. Front door panel-1992-98 Deville and Fleetwood

ea63dcb.jpg

Fig. Carefully pry up the power window switchplate and . . .

5e6e08a.jpg

Fig. . . . gently remove it from the door panel

42aebbe.jpg

Fig. Remove the door pull strap retaining screw covers by gently prying them off

342330d.jpg

Fig. Remove the door pull strap retaining screws

b4ba006.jpg

Fig. Gently pull the inside door handle panel down and . . .

6a6b4b0.jpg

Fig. . . . release the rod from the handle

435710f.jpg

Fig. Carefully lift up the door panel to release the . . .

aa0d077.jpg

Fig. . . . retaining pegs on the door panel

9275228.jpg

Fig. Do not pull the panel too far away from the door, as some components still have wiring harness connected

a232e57.jpg

Fig. Detach any necessary wiring connectors and remove the door panel from the vehicle
  1. Disconnect the negative battery cable.
  2. Insert a flat-bladed tool between the door panel and the rear edge of the power window switch plate to disengage the retainer from the panel.
  3. Slide the power window switch plate forward, then label and detach the wiring connectors.
  4. Remove the power door lock switch plate retaining screw. Remove the switch plate and detach the wiring connector.
  5. Remove the pull handle retaining screws.
  6. Using a thin-bladed tool, carefully pry the courtesy lamp lenses off. Remove the courtesy lamp bulb.
  7. Pinch the courtesy lamp retainers and pull out the lamp socket holder. Detach the courtesy lamp wiring connector.
  8. Remove the door panel retaining screws.
  9. Using tool J-2459B or equivalent, disengage the door panel fasteners from the holes in the door. Detach any remaining wiring connectors and remove the door panel.
To install:
  1. Position the door panel close to the door and attach the wiring connectors.
  2. Align the door panel fasteners with the holes in the door. Push in on the door panel to install it to the door.
  3. Install the door panel and pull handle retaining screws.
  4. Install the courtesy lamps and switch plates.
  5. Connect the negative battery cable.

I really hope help you with this (remember rated it) Good luck.

Oct 12, 2009 | 2001 Cadillac DeVille

1 Answer

Need to remove left rear door panel


  1. If equipped, remove the window crank handle by using a retaining clip removal tool.
  2. Remove the door handle bezel by inserting a flat trim removal tool between the door panel and handle bezel to release the locking tabs.
  3. Remove all door panel electrical connectors .
  4. Remove the door panel push pins and trim screws. Lift the door panel up and out to release the door panel locking tabs.

May 22, 2009 | 2006 Chevrolet Silverado

1 Answer

Window regulator replacement


Window Regulator, Rear Door, Explorer Removal
  1. Remove the rear door trim panel and watershield. Refer to Section 01-05B .
Trim Panel, Rear Door, Explorer, Hi-Series Four-Door Removal and Installation
  1. Remove the two screws retaining the rear door trim panel (27406) located above the door handle.
  1. Remove trim cup at the door handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.
  1. To remove window regulator switch plate (14524) , use notch located at lower end of plate using a screwdriver to lift and remove.
  1. Remove window regulator switch plate from rear door trim panel pulling wire harness from rear door trim panel .
  1. From bottom of window regulator switch plate , remove two screws and disconnect connector from window regulator control switch (14529) .
  1. At each plastic clip location, pry the rear door trim panel away from the door inner panel using the door trim panel removing tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent.
  1. Remove panel, lift slightly to remove flange at the top of rear door trim panel from trough in the glass weatherstrip. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the rear door trim panel to the door inner panel, firmly loading clips into slots provided on rear door trim panel .
    33c9359.gif
  1. If equipped with power windows, disconnect the wire from the regulator.
  1. Remove the rear door window glass as described in this section.
  1. Remove the window guide, if equipped, (nuts and washers). Remove guide from door belt opening.
  1. Remove three 1/4-inch rivets attaching motor bracket (electric) to inner panel and two 1/4-inch rivets attaching regulator lower bracket to inner panel. Use drift punch to knock out center pins for each rivet. NOTE: Use care not to enlarge sheet metal holes in the door inner panel when drilling.
  1. Using a 1/4-inch diameter drill, drill out the remainder of the rivet.
  1. Remove two upper regulator attaching nuts.
  1. Remove regulator from the front door (20125) .
Installation
  1. Lubricate regulator mechanism with Multi-Purpose Grease D0AZ-19584-AA or equivalent.
  1. Install regulator into access hole in inner panel.
  1. Position regulator using upper regulator studs and tabs on motor mounting bracket (electric) or cup mounting plate (manual).
  1. Install rivets attaching regulator to door inner panel (1/4-20 x 1/2-inch bolt and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used as alternates).
  1. Install two upper regulator attachment nuts.
  1. Install door glass as outlined under Door Glass Installation.
  1. Adjust glass as outlined under Adjustments .
  1. Reconnect wire to regulator, if equipped.
  1. Check operation of window regulator.
  1. Install door watershield and trim panel. Refer to Section 01-05B .

Apr 11, 2009 | 1994 Ford Explorer Limited

1 Answer

I have a 1998 Ford Explorer.


  1. Remove the rear pivot arm; refer to Pivot Arm—Rear . 7981ec7.gif
  2. Remove rear pivot arm.
    1. Lift the pivot arm nut cover.
    1. Remove the nut.
    1. Remove the pivot arm.
  1. Remove the liftgate door trim panel; refer to Section 501-05 . Remove the (A) liftgate handle to liftgate screws and the (B) liftgate handle. Remove the liftgate trim panel screw access plug. Remove the screw.
  2. Remove the liftgate door trim panel.
    1. Use Windshield and Molding/Trim Removal Kit to remove the liftgate door trim panel from the liftgate window opening.
    1. Push the liftgate door trim panel toward the top of the liftgate and remove the liftgate trim panel. 9e75e00.gif
  1. Position the watershield aside to gain access to the rear wiper motor.
  1. Remove rear wiper motor.
    • Disconnect electrical connector.
    • Remove three retaining bolts.
    • Remove rear wiper motor.
good luck.

Jan 10, 2009 | 1998 Ford Explorer

1 Answer

97 VW Jetta right rear power window off track


There should be six or seven allen wrench screws around the edge of the door panels. Loosening these releases the retaining clips inside. You will then want to remove the manual window crank if you have one by laying two fingers flat on the door panel and pushing the ring around the base of the crank sideways. You might have to rotate around this as it only pushes one way. Next you will have to remove the two large golden screws directly under the door panels handle. If you have rear door panel speakers you will have to politely pry off the speaker grill with a flat blade screwdriver and remove the speakers four screws and the wire clip from behind the speaker. You will also have to unscrew the door lock post. Then you should be able to lift the door panel up to release the top lip of it from the door.

Dec 29, 2008 | 1997 Volkswagen Jetta

Not finding what you are looking for?
1993 Mercury Grand Marquis Logo

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

fordexpert

Level 3 Expert

5522 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...