Where is the crankshaft position sensor located?

Question edited for clarity.
Question moved to model category.

Crankshaft position sensor location - Colorado Fans

coloradofans.com https://www.coloradofans.com > threads > crankshaft-...
Dec 16, 2009 - Hey everyone.. do ya know where the crankshaft position sensor is located on our engines? It would be a big help if someone could point me ...

Crank Positioning Sensor Relearn - Colorado Fans
Oct 7, 2006
No start after replacing Camshaft Position Sensor
Mar 2, 2012
Camshaft Crankshaft sensor ' Chevy Colorado & GMC Canyon
Feb 22, 2015
Colorado won't start after replacing the Camshaft Actuator ...
Sep 11, 2012
More results from www.coloradofans.com
..

https://www.google.com/search?q=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&rlz=1C1CHBF_enUS982US982&oq=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&aqs=chro -------------------https://www.google.com/search?q=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&rlz=1C1CHBF_enUS982US982&oq=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&aqs=chrome..69i57j33i299l3.7225j0j7&sourceid=chrome&ie=UTF-8#kpvalbx=_VCj-YqCEB6GpptQPza2F-AU28

The role of the crankshaft position sensor is to determine the position of the crankshaft, the crankshaft angle. It is usually with a camshaft position sensor work together - to determine the basic ignition timing. Car Diagnostic Tool

Hi Rusty, There's two links below showing the position of 2005 Ford Explorer Crankshaft Position Sensor and the 2008 ford edge camshaft sensor location. It seems like they're all in the same position, I hope this helps.....CHEERS
..
2005 Ford Explorer Crankshaft Position Sensor Location

2008 ford edge camshaft sensor location

For testing crank sensor,check the help link below:---How to test Crankshaft Position Sensor? http://fordrepairhelp.blogspot.in/2012/03/how-to-test-ford-focus-crankshaft.html
----------

• How to test Crankshaft Position CKP Sensor?

---------------
Crankshaft Position Sensor Operation?

----------------
Replace Camshaft position sensor and Crankshaft Position Sensor? http://technoanswers.blogspot.in/2012/06/2005-dodge-durango-replace-camshaft.html
----------
GMC Crankshaft Position (CKP) Sensor Replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-crankshaft-position-ckp-sensor.html

------------
These details will help.
Thanks.

The check engine light doesn't have to come on with a bad crank sensor ,your vehicle has two , one for lower rpm an one for higher speeds . A&B
The two crankshaft sensors are located on the front bank (BANK 2) of the engine block between cylinders 4 and 6. Crankshaft position A sensor is located in the upper crankcase and crankshaft position B sensor is located in the lower crankcase. Both sensors extend into the crankcase and are sealed to the engine block with O-rings. The crankshaft position sensors are not adjustable.

The crank sensor is located on the engine near the flywheel axis of the crankshaft.

Crankshaft Position Sensor Removal & Installation To Remove:
Location of the crankshaft position sensor on the 2.4L engine
Location of the crankshaft position sensor on the 3.0L engine
Location of the crankshaft position sensor on the 3.3L and 3.8L engines
NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.

1. Disconnect the negative battery cable.
2. Raise and safely support the vehicle.
3. Disconnect the crankshaft position sensor electrical connector.
4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.

To Install:
NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.

1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
2. Connect the crankshaft position sensor electrical connector.
3. Lower the vehicle.
4. Connect the negative battery cable.

Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

can u please tell me where on my 2004 chrysler pacifica is the crankshaft sensor located?

7X Crankshaft Position (CKP) Sensor
Lower rear of engine
4
25
--
24X Crankshaft Position (CKP) Sensor
Right hand side of engine, at end of crankshaft, behind harmonic balancer
7X Crankshaft Position (CKP) Sensor
Lower rear of engine
4
25
--
24X Crankshaft Position (CKP) Sensor
Right hand side of engine, at end of crankshaft, behind harmonic balancer
Right hand side of engine, at end of crankshaft, behind harmonic balancer