Question about 1997 Plymouth Breeze

2 Answers

1999 Plymouth Breeze - rear brakes locking up

Burning up shoes about every 50 miles,
changed wheel cylinders
replaced master cylinder
adjusted e-brake so there is no tension on cables

is the next step to replace rear brake lines? Just the rear portion that has rubber hosing or all the way back?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

You have a proportioning valve stuck. From the master the brake lines will run down the wheel well to another valve then out to the front calipers and rears when the prop valve sticks or freezes it then causes the rear or front system to lock up or not proportion the system evenly. 2. If that is not the case you may have contamination in the lines or the rubber brake hoses whick allow fluid to pass through it will not allow it to return almost acting like a back check valve therefore keeping you brakes on.

Posted on Jul 13, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Plymouth Master
  • 412 Answers

HAVE A LOOK AT REAR FLEXHOSES..THE BRACKET THAT HOLDS THEM TO BACKING PLATES MAY HAVE RUST BUILDUP WHERE IT GOES AROUND HOSE..IT IS SQUEEZING HOSE AND NOT LETTING FLUID RETURN PROPERLY WHEN BRAKE IS RELEASED..YOU CAN TRY SPREADING THIS AREA WITH A SCREWDRIVER OR REPLACE HOSES..I HOPE THIS HELPS

Posted on Jul 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Rear drums smell like something is burning and are hot.


remove the drum and inspect you job. small shoe on front big shoe on back.brake lube on the backing plate.lose the adjuster and inspect,lube the adjuster, give more free play on your parking brake cable 3 click is the normal before lock the wheel. Inspect the master cylinder for overfeel, remove any fluid over the max level. inspect the fluid for contamination(burn smell or oily)flush the system. lift the Jeep and pump on the brakes,if the wheel is locking open the bleeder screw.if brake fluid is under pressure,replace the hoses.
good luck

Oct 24, 2014 | 1999 Jeep Cherokee 4WD

1 Answer

Brake pedal


Did you ensure that the master brake cylinder was topped up properly whilst you bled the back brake shoes?

If you did so and the brakes are free of air in the lines, then you still have to adjust the brake shoes to their operating position. Secure vehicle from movement. Jack back wheels of the ground, support with jack stands. Remove the rubber grommets that covers brake adjustment wheels. Turn star wheel adjuster with special adjustment tool or a wide blade screw driver. Lock the wheels with the adjustments, push in brake pedal until you have pressure, back off adjustments until wheel runs freely. you should have plenty of pedal now. Make sure master is at the right level at all times.

If you don't have pedal now then I would suggest you still have air in the brake lines.. If you pump the brakes until you have pressure and the pedal feels spongy , then you still have air in the line somewhere. Bleed until air is removed.

Mar 21, 2014 | Isuzu Rodeo Cars & Trucks

1 Answer

1999 Ford E350 van problem: brake pedal is soft; have replaced master cylinder, rear wheel cylinders, rear brake shoes and drums, front calipers, rotors and discs; have bled master cylinder before...


Good question, on the antilock system is a bleader too and bleade it the same way you bleade the caliper. After all is done adjust the rear brakes, they should have a drag to them.

Feb 23, 2011 | 2007 Ford E-350 Super Duty Length XLT

1 Answer

Corolla 2000 brakes, I did change master cylinder,


System may have air in it bleed from farthest wheel to closest.
If rear shoes are out of adjustment re adjust them
Possible but most pads require a "bedding in" 20 stops 50 to25mph or so.

Jul 28, 2010 | 2000 Toyota Corolla

1 Answer

"I just had a new brake booster Master Cylinder rear wheel cylinders and rear brake shoes installed, I drove 3 miles and the back brakes locked up. What can this be? 1998 chrysler sybring


Sorry to but in BUT

is this a high mileage car from what you discribe new Servo, Master Cylinder, Cylinders and rear brakes.????

Try the rear flexible brake pipe/s OLD RUBBER DELAMINATES well worth the swop. For the cost

360 Volvos used to be good at this one only after a brake fluid change

Old British Mechanic

May 08, 2009 | 1998 Chrysler Sebring

1 Answer

1999 nissan quest rear brake shoes need changing


help is here:
http://autos.groups.yahoo.com/group/villagerquest/

Drum Removal
  1. Remove the rear wheel and the tire assembly. Refer to Section 204-04 .
  1. Retract the brake shoes and loosen the brake adjuster screw.
975565f.gif
  1. Remove the brake drum.
----------------------
May require big hammer to loosen drum from axle flange. Hit between the the lugs, not on them.

------------------------------------------------------------------------------
#10 is access plug to back off adjusting wheel.

f9f31b5.gif
Item Part Number Description 1 2261 Rear wheel cylinder 2 — Dust boot (part of 2128) 3 2197 Wheel cylinder piston (part of 2261) 4 — Cup (part of 2128) 5 2204 Wheel cylinder piston cup spring (part of 2128) 6 — Wheel cylinder housing (part of 2261) 7 — Brake shoe hold-down pin 8 — Access hole (part of 2212) 9 — Rear brake bleeder screw (part of 2261) 10 — Access hole plug 11 — Rear wheel cylinder bolt 12 2212 Rear brake backing plate 13 — Rear brake backing plate bolts 14 2N790 Parking brake lever clip 15 — Spring washer 16 — Secondary brake shoe and lining (part of 2200) 17 — Brake shoe hold-down spring (part of 2B514) 18 — Lower retracting spring (part of 2B514) 19 2A637 Parking brake lever 20 — Parking brake lever pin 21 2A177 Brake shoe adjusting lever 22 — Adjuster lever pin (part of 2A177) 23 — Primary brake shoe and lining (part of 2200) 24 — Upper retracting spring (part of 2B514) 25 2041 Brake adjuster screw

--------------
Shoes Removal

Take a picture and remember how each part goes and attaches
  1. Remove the brake drum, refer to Drum in this section.
  1. Remove the upper retracting spring.
  1. Remove the lower retracting spring.
  1. Remove the self-adjuster.
38bcaa0.gif
  1. Remove the hold-down springs.
  1. Remove the parking brake lever clip and the parking brake lever.

Apr 17, 2009 | 1999 Nissan Quest

1 Answer

I need a schematic for the rear brakes on an F150 super cab with 4.6L automatic trans 4wheel drive


Drum, Rear Brake System Standard Rear Brake
9969082.gif
Item Part Number Description 1 2069 Brake Shoe Hold-Down Spring Pin 2 — Rear Wheel Cylinder Retaining Bolt (2 Req'd) 3 — Washer (2 Req'd) 4 — Anchor Pin (Part of 2211) 5 — Wheel Cylinder 6 2028 Brake Shoe Anchor Pin Guide Plate 7 2A637 Parking Brake Lever 8 2296 Brake Shoe Retracting Spring (Short) 9 2296 Brake Shoe Retracting Spring (Long) 10 2200 Rear Brake Shoe and Lining (Secondary) 11 — Washer 12 2106 Parking Brake Lever Pin Retainer 13 — Brake Shoe Adjusting Lever Cable Guide 14 2A642 Primary Brake Shoe Parking Brake Lever Link 15 2A601 Parking Brake Link Spring 16 2068 Brake Shoe Hold-Down Spring 17 2A176 Brake Shoe Adjusting Lever 18 2048 Brake Shoe Adjusting Screw Socket 19 2047 Brake Shoe Adjusting Screw Nut 20 2041 Brake Adjusting Screw 21 2049 Brake Shoe Adjusting Screw Spring 22 2200 Rear Brake Shoe and Lining (Primary) 23 2A178 Brake Shoe Adjusting Lever Cable 24 2211 Brake Backing Plate
Heavy Duty Rear Brake
6dcb5d2.gif
Item Part Number Description 1 — Rear Wheel Cylinder Retaining Bolt 2 00538 Lock Nut 3 2212 Rear Brake Backing Plate 4 2262 Rear Wheel Cylinder 5 2A642 Primary Brake Shoe Parking Brake Lever Link 6 2A601 Parking Brake Link Spring 7 2A637 Parking Brake Lever 8 2106 Parking Brake Lever Pin Retainer 9 — Parking Brake Lever Bolt 10 — Secondary Shoe Assembly 11 2A179 Brake Shoe Adjusting Lever Cable Guide 12 2068 Brake Shoe Hold-Down Spring 13 — Adjusting Lever Pin 14 — Adjusting Lever Return Spring 15 2A176 Brake Shoe Adjusting Lever 16 2047 Brake Shoe Adjusting Screw Nut 17 2049 Brake Shoe Adjusting Screw Spring 18 2041 Brake Adjuster Screw 19 — Primary Shoe Assembly 20 2068 Brake Shoe Hold-Down Spring 21 2200 Rear Brake Shoe and Lining 22 2035 Brake Shoe Retracting Spring 23 2A178 Brake Shoe Adjusting Lever Cable 24 2092 Brake Adjusting Hole Cover 25 2069 Brake Shoe Hold-Down Spring Pin
The rear drum brakes:
  • Have internal shoes that expand against the brake drum (1126).
  • Are a single-anchor type.
  • Are actuated by one rear wheel cylinder (2262).
  • Have two pistons in the rear wheel cylinder (2261). One exerts force against the upper end of the primary shoe; the other exerts force against the upper end of the secondary shoe.
  • Adjust rear brake shoes and linings (2200) automatically.
  • Need manual brake adjustment if the adjusters are not operating properly or after the rear brake shoes and linings have been replaced.
When the brake pedal is applied, hydraulic fluid pressure forces the pistons in the rear wheel cylinder outward, moving the rear brake shoes and linings against the brake drum.
The rear drum brake system includes the parking brake mechanism. Refer to Section 206-05 .

Apr 04, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Right rear brake has slow brake fluid leak.It's a 99' Ford Taurus


leaking fluid will not cause a brake to lock up unless the wheel cylinder is leaking and caused the brake shoe to swell. If so, you need a new wheel cylinder.

Mar 01, 2009 | 1999 Ford Taurus

Not finding what you are looking for?
1997 Plymouth Breeze Logo

1,136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...