Question about 2004 Dodge Ram 1500

1 Answer

I had a new under dash harness replaced about 2 years ago because my a/c wouldnt shut off with the key in the off position. now it is doing the same thing except the a/c will not work unless you wiggle the harness and then the harness gets hot so i turn it off . whats wrong ? Thank you !!!!

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check the plug to the blower motor to see if it is melting. There is a service bulletin on it

Posted on Aug 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i replace a ignition lock cylinder on a


Not really a job for a non-mechanic. Column covers off, switches out of the way, wiring disconnected, column dropped down under the dash, bolts chiseled out, big job.

Sep 12, 2014 | 1999 Pontiac Grand Prix

2 Answers

1991ford van won't shut off


It will when it runs out of gas....just trying to lighten the situation up. Sorry..

Seriosly, are you saying that when you turn the ignition switch to the off position the engine continues to run?

May 29, 2014 | Cars & Trucks

1 Answer

I was having problems with my starting, when I got a jump it started... Then the other day it wouldnt do anything at all and my key got stuck in the ignition... along with making a clicking noise. So we...


I suspect you mechanical ignition switch if faulty. This is located on top of the steering column by the drivers feet. Disconnect battery to prevent activation of airbag .Remove the panel under the steering wheel and the nuts or bolts holding the column to the dash. Lower the column and you will see a rectangular box mounted on top that has a wiring harness on the driver side and a metal rod out of the top. This is the mechanical switch that I believe is bad. Mark the location with a scribe or sharp metal point along 2 sides. Remove mount screws, unplug harness, and carefully remove metal rod from bottom of switch. Install metal rod in new switch, making sure the rod moves freely and does not bind up. Remount switch, aligning with the marks you made on the column. Put key in lock cylinder and test operation of the switch by turning fully to the start position, watching that metal rod for movement and return of switch to normal operating position. If you have it aligned correctly you will see the rod move as you turn the key to the start position and move as you release the key. Plug in the wire harness and and reinstall column, then panel and reconnect battery.
Hope this helps!!

Dec 11, 2010 | 1997 Oldsmobile Achieva

1 Answer

1990 cadillac seville wont start, it say starting disabled, what can i do to try and make this go away?


sounds like your going to have to replace the ignition tumbler,that is if your key has the small chip in it mounted in rubber,if you would like to disable it for good you can just buy another cylinder with key and plug it into the harness under the dash that runns up to your current tumbler and just put the key in the on position in the new tumbler and just tuck the whole thing up under your dash and the car will think the key is in the ignition and disable the alarm and your normal key will just start the car as normal,hope this helps

Oct 12, 2010 | 1990 Cadillac SeVille

1 Answer

My car alarm goes off when I unlock, then open the car door. (with key, since the fob was lost more than a year ago). When the alarm stops and I try to start the car the alarm goes off again. Cannot...


You will need to find a push button or valet switch (hidden somewhere under the dash), This will help you in turning off the alarm. Once you find this button, turn the ignition key to the run position, do not try to start the vehicle, and push down button for about 3 to 5 seconds this will shut alarm off. Good Luck.

Jun 23, 2010 | 1998 Volkswagen Golf

2 Answers

Ignition switch does not turn on my 2001 c320


2001mercedes-benz320 will not start after losing power and died.

May 31, 2009 | 2001 Mercedes-Benz C-Class

1 Answer

Losing Power/ignition 2005 Jetta GLI


Check out the vwfixx.com forum online. One guy has a step by step procedure on removing the ignition, says it takes about a half an hour.

Apr 02, 2009 | 1998 Volkswagen Jetta

1 Answer

Car was stolen broke the ignition


REMOVAL

  1. On models equipped with airbag, disarm airbag as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
  2. On all models, disconnect battery ground cable.
  3. Remove ignition switch as described under STARTING AND CHARGING SYSTEMS/COMPONENT REPLACEMENT AND REPAIR PROCEDURES/IGNITION SWITCH.
  4. Remove key light case from lock body, if equipped.
  5. On 1989 Accord models, place ignition lock cylinder in the ACC position.
  6. On except 1989 Accord, place ignition lock in the I position.
  7. On all models, position suitable punch into hole on lock cylinder housing and depress pin, then remove lock cylinder from housing.
INSTALLATION

  1. On 1989 Accord models, install ignition lock cylinder as follows:
    1. Place ignition lock cylinder in the LOCK position.
    2. Rotate key until it is almost at the ACC position, then insert lock cylinder until pin contacts housing.
    3. Rotate key to ACC position, then push pin in and insert lock cylinder into housing until pin clicks into place.
  1. On except 1989 Accord, install ignition lock cylinder as follows:
    1. Place ignition lock cylinder in the O position.
    2. Rotate key until it is almost at the I position, then insert lock cylinder until pin contacts housing.
    3. Rotate key to I position, then push pin in and insert lock cylinder into housing until pin clicks into place.
  1. Install ignition switch and connect battery ground cable.
SRS wire harness is routed near the ignition switch.

CAUTION:
  • All SRS electrical wiring harnesses are covered with yellow outer insulation.
  • Before disconnecting the SRS wire harness, install the short connector on the airbag.
  • Replace the entire affected SRS harness assembly if it has an open circuit or damaged wiring.
IGNITION SWITCH
  1. Remove the steering wheel, then remove the steering column covers.
  2. Disconnect the 7-P connector from the under-dash fuse box.
  3. Insert the key and turn it to "0."
  4. Remove the 2 screws and replace the base of the switch.

Feb 13, 2009 | 1992 Honda Accord

2 Answers

2004 alero


If the security light is flashing when that happens, you need to turn the key to the ON position, and let it sit for 10 minutes, so it can reset the security code. Start it up as normal and let it idle for 5 minutes.

Nov 04, 2008 | 2004 Oldsmobile Alero

Not finding what you are looking for?
Cars & Trucks Logo

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...