Question about 2006 Jeep Liberty

1 Answer

My ABS, BAS ESB and Stability lights are all on. How do I reset these?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Its the speed sensor in one of the wheels. mine was left rear.

Posted on Aug 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to turn off eps bas traction control abs lights


when repair is done the warning light will reset

Aug 24, 2015 | 2006 Jeep Liberty

2 Answers

Esp bas light is staying on on my chrysler 300 what is that and how do i fix


See a repair shop that does brakes. Be prepared to pay for a diagnostic fee to find problem.
That's an ABS light.

Nov 11, 2014 | Chrysler 300 Cars & Trucks

2 Answers

ABS/ Traction control light/BAS & brake light on in 2008 dodge grand caravan


It is safe to drive. You need a scan tool to get a code out of it. Could be as simple as a wheel speed sensor going bad. All of these lights will work together normally. The traction control uses the ABS to gain traction, and the Brake Assist System is part of the stability control. Also uses the ABS.

Oct 03, 2012 | 2008 Dodge Grand Caravan

1 Answer

Code c 2204 esb bas light stays on


Hi there:


DTC C2204 - Dynamics Sensor Internal

This light is on most likely due to a speed sensor failure. Either the rear one in the rear diff housing or the right or left front speed sensor. You will need someone with a full level scan tool to scan the ABS module to find which sensor it is and then replace that sensor accordingly.

The location of the Dynamic internal sensor: It is located in lower part of the centre console . exactly on the right side of the air bag module.




REMOVAL


1. Disconnect and isolate the battery negative cable from its battery post.
2. Remove the instrument panel center stack console.



6_27_2012_8_53_28_pm.jpg


3. Roll back the front floor carpet from under the instrument panel toward the rear of the vehicle for access to components.
4. Remove the fasteners (2), then instrument panel center support brackets (2). There is one bracket on each side of tunnel structure.

6_27_2012_8_54_35_pm.jpg

5. Disengage the right intermediate floor distribution duct (2) from the stud located on the floor support (3) and move it aside as necessary to access the dynamics sensor.

6_27_2012_8_55_44_pm.jpg

  1. Disconnect the wiring harness connector (3) at the dynamics sensor (2).
  2. Remove the screws (1) mounting the dynamics sensor to the mounting bracket on the floor pan tunnel (4).
  3. Remove the dynamics sensor (2).




6_27_2012_8_56_21_pm.jpg


Hope this helps.

Jun 27, 2012 | Dodge Charger Cars & Trucks

1 Answer

Asb esb light


abs light on after 7 miles switch off drive another 7 mi,les back on,merc a 160. advise please. done most thing s on Lofftys cd

Feb 16, 2010 | 1997 Audi A8

1 Answer

Abs bas and esb lights wont go off.


you need to use a diagnostic abs computer

Aug 11, 2009 | 2006 Jeep Liberty

1 Answer

ABS light on fronm start up. Had problems witht he


just a guess on this but but have you tried resetting the computer for the switch?

Jun 27, 2009 | Jaguar XJ8 Cars & Trucks

1 Answer

ETS light stay on all the time.


ABS--BAS--ESP
The Electronic Traction System uses you ABS tu assist in stability

Most likely cause is the 'stop lamp switch'
It is a electric switch located on the brake pedal inside the car, about half way up on the brake pedal.
Pretty cheap too, I think the switch is only like $25 bucks.
2 connectors on the switch and then it turns out.
hope that helps

Jun 26, 2009 | 1996 Mercedes-Benz C-Class

1 Answer

I have a 2006 jeep liberty and three lights are staying lit and


You need to take the jeep to a dealer or a good mechanic who can retreive the codes out of the computer. You may have a module problem but I will not guess without knowing the codes.

Feb 11, 2009 | 2006 Jeep Liberty

Not finding what you are looking for?
2006 Jeep Liberty Logo

Related Topics:

955 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...