Why is no fuel getting to the injectors?

Silverado 1500 or 2500 or 3500 or HD? no pickup told
not told the job you are doing>??
remove them all ,or scope them or just what, no job told
no end goal or task told. sorry can guess it.

like most V6/8 now , it is a sandwich.
the service manual covers all,l buy it rent it.?
toss dice and land on 1500
the rail on this engine, fuel rail like all , intake manifold injectors used;. all injector held down by both rails. left and right
now the steps to off them if is the job,
pull the isolator seen photo 1, far below.
1: pull left rail and right rail
Remove and discard the fuel injector retainer clips by installing EN-51097 injector retaining clip installer and spreading both sides of the clip evenly.
Always use NEW fuel injector collars supplied with injector when installing the new injector. If reinstalling the injector, it is not necessary to remove the collars unless the collars are being replaced.
Replace the injector seals as needed. Refer to Fuel Rail and Injectors Cleaning and Inspection.
Note
Inspect the injectors to be sure that they are clean and free of debris prior to installation. Do NOT lubricate the injector seals. Rebuild the fuel injectors whenever the injector has been removed from the fuel injector rail.


now I will past the other page rails off per the manual read to you.
just bank 1, i am to lazy to post both
step 1 rail off bank1.
Note
Inspect the injectors to be sure that they are clean and free of debris prior to installation. Do NOT lubricate the injector seals. Rebuild the fuel injectors whenever the injector has been removed from the fuel injector rail.

1. Remove the fuel pump insulator. Fuel Pump Insulator Replacement
2. Remove the fuel injector intermediate pipe position?1. Fuel Feed Intermediate Pipe Replacement - Position 1
3. Clean the cylinder head pocket around the injectors of any dirt or buildup.
4. Disconnect the electrical wiring harness connectors from the fuel rail.
5. the fuel rail fasteners are retained in the fuel rail by keepers and may be difficult to remove.Remove the fuel rail fasteners?(1) securing the injector rail?(2).
   Install two sets of EN-49248 remover?(3).
6. Install one remover in each of the fuel rail fastener bores.
7. Remove by turning each section of the EN-49248 remover an even amount to pull the fuel rail and injectors out evenly.
8. CAUTION
9. Remove the fuel rail assembly carefully in order to prevent damage to the injector electrical connector terminals and the injector spray tips. Support the fuel rail after the fuel rail is removed in order to avoid damaging the fuel rail components.
10. Cap the fittings and plug the holes when servicing the fuel system in order to prevent dirt and other contaminants from entering open pipes and passages.
11. 1. Simultaneously lift both ends of the fuel rail?(2) and remove the fuel rail assembly from the cylinder head.
12. Remove and DISCARD the fuel injector seals.
13. Some vehicles were not originally equipped with fuel injector dust seals. A NEW seal must be installed when the injectors are removed.
    Remove and DISCARD the fuel injector dust seal (1).
14. NOTE
    Note
    Whenever the fuel injectors are removed from the cylinder head or fuel rail, they will need to be rebuilt. Fuel Rail and Injectors Cleaning and Inspection
    If replacing the fuel injection fuel rail, remove the fuel injectors. Fuel Injector Replacement

Installation Procedure, skipped me. the service manual lists 4 tools
per

Special Tools

1. EN-49248 Injector Rail Assembly Remover
2. EN-51105-1 Injector Seal Installer and Sizer
3. EN-49245-3 Fuel Injection Seal Installer Sizer
4. EN-49245-4 Fuel Injection Seal Installer Sizer

this is first. pull the isolator.

this one step is the GET TO ANSWEREd
Injector work 10x more complex and special tools needed x4

How much pressure and volume is getting to the rail? Could have a restricted like. Also check the injector connectors to make sure that the computer is sending the pulse to fire to the injectors.

If the pump kicks on, then it should be getting to the rail.
Sounds like an immobilizer issue (Not powering the injectors).
Disconnect a hose from the fuel rail inlet point (put it into a bottle or tub) and check if fuel is pumping during cranking.
If you get fuel at the rail, check immobilizer or ECU.

sounds like an electrical problem .pump isnt coming on .turn on key listen for fuel pump to come on for 10 seconds then shut off on its own. If you dont hear the pump then its probley fuel relay . next check wires are plugged into fuel pump. lots of cleaning ?? is the fuel rail screen plugged ???? disconnect before rail if the pump comes on next. turn on key check for fuel pumping out line .

it sounds maybe a transmission problem try some stop slip for it. then also you could try a fuel injector cleaner. if that doesnt work then it might be the speed senor

lets say you have power and fuel is pumping it goes from pump to fuel rails in one long line if fuel is at port on rail then ck injectors for hot and ground hot with key on ground with engine turning injectors get ground from ecm ,if no ground ck for bad ground wires then ck ecm ,. if no power to pump ck fuse and fuel pump relay and wire system. some times replacement parts are bad.

FIRST NEED TO RELIEF FUEL PRESSURE REMOVE GAS CAP RELIEF GAS PRESSURE IN FUEL TANK.THEN REMOVE FUEL PUMP RELAY THEN START ENGINE UNTIL IT DIES LACK OF FUEL,CRANK ENGINE OVER FEW MORE TIMES MAKE SURE FUEL OUT OF FUEL LINES. THEN YOU NEED TO REMOVE AIR CLEANER CROSS OVER TUBE ABOVE FUEL RAILS. DISCONNECT LINES AT THE ENDS OF THE FUELS RAILS ASSEMBLY. MARK AND DISCONNECT THE FUEL INJECTOR WIRE HARNESS CONNECTORS. REMOVE THE FUEL RAIL RETAINING BOLTS, DISCONNECT THE VACUUM LINE FROM THE FUEL PRESSURE REGULATOR. REMOVE THE FUEL RAIL ASSEMBLY FROM THE ENGINE. IF YOU HAVE AUTOMATIC TRANSMISSION REMOVE THE THROTTLE PRESSURE CABLE AND BRACKET TO REMOVE THE FUEL RAIL ASSEMBLY.TO REMOVE FUEL INJECTORS JUST REMOVE CLIPS THAT RETAIN FUEL INJECTORS IN FUEL RAIL. BESURE GO TO DEALERSHIP BUY NEW FUEL INJECTORS O - RINGS.APPLY A SMALL AMOUNT OF ENGINE OIL TO THE O - RINGS TO AID IN INSTALLATION. TORQUE FUEL RAIL BOLTS TO 100 INCH LBS.

You said, 'fuel injectors are not injecting fuel into fuel rail' but it's my understanding that the fuel rail gasoline is supplied by the pump, and the fuel injectors just pulse to allow fuel to get to the cylinders. I would check out the fuel delivery problem further. Check for pressure in the fuel rail that is within specs.

If not, then the pump or fuel pressure regulator may be the problem. Check the fuse for the fuel pump. If good, then the pump may be bad in the tank.

Good luck on this.

YOU HAVE TO RELIEVE FUEL SYSTEM PRESSURE.REMOVE THE INTAKE MANIFOLD COLLECTOR.REMOVE VACUUM HOSE FROM THE FUEL PRESSURE REGULATOR.REMOVE FUEL HOSES FROM THE FUEL RAIL.REMOVE FUEL RAIL BOLTS AND INJECTOR HARNESS CONNECTORS.REMOVE INJECTORS AND FUEL RAIL AS AN ASSEMBLY.REMOVE INJECTORS FROM RAIL BY PUSHING THEM OUT.REMOVE DISCARD FUEL INJECTORS ORINGS REPLACE WITH NEW ORINGS LUBRICATE NEW ORINGS WITH CLEAN ENGINE OIL.YOU HAVE TO BUY ORINGS FOR FUEL INJECTORS AT THE DEALERSHIP.BESURE TO TAKE OLD ORINGS SO WILL GET THE RIGHT SIZE ORINGS.

i have an 88 chevy truck, not getting gas to come out of injectors.. getting gas all the way through the lines all the way up to the tbi but not out of injectors. pressure gage check done! new fuel regulator done! . u can put gas in the throttle body and it fires right up.??